Related Manuals for ATN ThOR-HD 384 2 - 8x
Summary of Contents for ATN ThOR-HD 384 2 - 8x
- Page 1 ThOR-HD Series THERMAL SMART HD RIFLESCOPE M A N U A L THOR-HD USER’S GUIDE (REV. 4, AUGUST, 2017) AMERICAN TECHNOLOGIES NETWORK CORP .
- Page 2 The instructions in this manual are for informational use only and subject to change without notice, this manual is not to be construed as a commitment by ATN Corp. ATN Corp. assumes no responsibility or liability for any errors or inaccuracies that may appear in this book. ©2017 ATN Corp. All rights reserved.
-
Page 3: Table Of Contents
TA B L E O F C O N T E N T S FEATURES ........4 APPLICATION . -
Page 4: Features
Record videos and photos onto a microSD card. Never again forget to record that perfect shot with ATN’s patented RAV (Recoil Activated Video). Use ATN’s Smart Range Finder to quickly range in on your target and allow the ballistic calculator to make instantaneous corrections to your POI (Point of Interest) on the fly. -
Page 7: Preparing The Device
4. Ensure that all optical surfaces are clean and ready for use. NOTE If any accessories are missing or broken contact ATN’s Customer Ser- vice. INSTALLATION OF BATTERIES The Thor-HD will operate on four AA-type Lithium batteries. -
Page 8: Firmware Update
In the event of a power failure during an update. The device may crash, corrupting its system files. It will need to be sent back to the ATN factory for service. DO NOT USE an additional source of power during firmware update! Update the new firmware as follows: 1. -
Page 9: On/Off
ON/OFF To TURN ON the device, press and hold the POWER Button until you see the ATN splash screen. To TURN OFF the device, press and hold the POWER Button until the “Shut down... -
Page 10: Mounting Your Scope
3. Tighten the fixing screws. NOTE Fixing screws may need to be tightened after con- tinuous shooting. ATN rec- ommends using “Loctite” to ensure screws do not loosen up during shooting. COMPASS CALIBRATION When the compass needs to be calibrated, the word “CAL”... -
Page 11: Interface
I N T E R FAC E HOMESCREEN The Homescreen will first appear when you switch on the device. It consists of Scales, Status Bar icons and different Information Widgets. SCALES • The E-Compass Scale shows yaw angle based on e-Magnetometer data. •... -
Page 12: Main Operations
Display widgets can be viewed in the System Set- tings. To enter System Settings, click on the ENTER button from Homescreen and access the Shortcut Carou- sel. Select the wrench icon with RIGHT or LEFT buttons and push ENTER button to enter the menu. -
Page 13: Shortcut Carousel
NOTE Your recording will automatically stop when the memory card is full or the battery is out of power. SHORTCUT CAROUSEL The ENTER button opens the menu and closes it down when pressed again. SHORTCUT CAROUSEL The Carousel will allow you to access a number of Shortcuts for quick access to your scope’s features. -
Page 14: Using System Settings
ENVIRONMENT Allows for input of various environmental data to improve ballistic cor- rection, such as wind speed and direction. SYSTEM SETTINGS Allows access to various system options and adjustments. Grouped switches consist of the following: WiFi module GPS module Bluetooth Ballistic RAV (Recoil module... - Page 15 On the left side of the Tab Bar you will find the Exit drop-down (select with arrow icon). Pressing the ENTER button will bring you back to the Home- screen. Movement between the tabs is carried out using the LEFT and RIGHT buttons Each tab includes subcategories.
-
Page 16: Functions
F U N C T I O N S PHOTO MODES From the Homescreen: press the LEFT button to TAKE A PHOTO. Depending on the selected mode you will make one or several photos. You can choose from the various photo modes in the System Settings. NOTE You must have a microSD card inserted in the device for these features to work, and all files will be stored on the microSD card. -
Page 17: Recoil Activated Video
To make changes: 1. Choose a Photo/Vi- deo Tab in System Set- tings. 2. Use the UP or DOWN buttons to select Time Lapse Settings. 3. Press the ENTER but- to enter the mode settings. While you are in this mode, the Time Lapse wid- get appears. - Page 18 1. Press the RIGHT button to Activate RAV from the Homescreen in order to Start Video recording. 2. Press RIGHT button again to stop Video recording. NOTE It may be best to turn OFF the Microphone in conditions of extreme wind.
-
Page 19: Rangefinder
While you are in this mode, the RAV widget appears and then after starting record the Time Counter appears. After activating the RAV function in the Shortcut Carousel, return to the Homescreen. Continue the activation process by pressing the Right button to activate the Video. - Page 20 take the readings (it will take a number of readings so try to keep your weapon steady); 2. put the arrow-mark under the target and press the EN TER button 3. if satisfied with the value, press the LEFT button to go back to the Homescreen, or repeat steps 1 and 2 if necessary.
-
Page 21: Zeroing
This allows you to create two separate profiles to fine tune your shooting solu- tions for both shorter and longer range shooting. In order to change the profile name to what you want, download and access the ATN Obsidian app. The app will allow you to connect your Phone/Tablet to your scope. - Page 22 NOTE You will need to obtain a target which thermal is able to see. ATN sells Ther- mal Targets, or you can use any of the following items: Cold or Hot water bottle, hand warmers, or foil based tape. To zero your rifle with the ATN device, you should follow the next few steps.
-
Page 23: Ballistic Calculator
NOTE In order to fine tune your zero. Select Zero Reticle once more. Press the ENTER button and select Zoom. Zoom in all the way and fire the weapon. If your POI is not where you had aimed. Move the Red reticle to the POI and Exit &... - Page 24 To edit a Profile you should select it (highlighted in red), press ENTER but- and choose the ac- tion you want to be done: Load, Copy (Duplicate) or Delete the selected profile. ENVIRONMENT There are a number of Environmental elements that may be entered to in- crease the precision of your shots.
- Page 25 The Ballistic Calculator will make your adjustments for you but only after you have entered the range to your target. Your sight offers several ways to accomplish this task. RANGEFINDER Select the Flag Icon from the Shortcut Carousel. Pressing the ENTER but- will take you to the Main Screen of the Range- finder feature.
-
Page 26: How To Perform A Nuc
• choose one of the presets or input the height manually; • accept the height with ENTER button and go back to the Main Screen. DISTANCE ENTRY If you are using other means such as a Laser Range Finder you may enter the distance man- ually using the Distance Entry shortcut. -
Page 27: Reticle Style Adjustment
button and select Zoom. Use the UP and DOWN buttons to zoom in and out on to the neutral pixel in order to isolate it. Once you have isolated the neutral pixel, press the ENTER button to escape from the zoom function. 7. -
Page 28: System Settings
You can change Reticle Color depending on cir- cumstances. Movement between the colors is carried out using the LEFT and RIGHT but- tons . Then press EN- TER button to accept your color. SYS T E M S E T T I N G S THERMAL CONTRAST —... -
Page 29: Photo/Video
PHOTO/VIDEO PHOTO MODE — in- cludes Single (capture a single photo), Time Lapse (series of photos at timed intervals) and Burst (up to 10 photos in one second) modes. B U R S T C O U N T — amount of photos in one second (2 –... -
Page 30: Profiles/Zero
RETICLE STYLE • Shape — you can choose the shape of your Reticle. • Color — you can choose the color of your Reticle. PROFILES/ZERO CURRENT • Zero Reticle — allows to enter zeroing mode. • Drag Function — the flight path and character- istics of bullets divided into types (G1 –... -
Page 31: Servicing
• Time — enter the time. • Time Zone — allows you to choose a geographical region with standard time. WIFI AND BLUETOOTH • Remote Controller — Remote Controller (Pair/Unpair) • Remote Controller Orientation — Wheel Front/Wheel Back • Rangefinder — Pair/Unpair Values are not changeable. -
Page 32: Warnings And Cautions
All your photos and videos are right at your fingertips. In order to download the latest version of the ATN Obsidian App. Please visit the iOS store or Google Play store. Search for “ATN Obsidian” install the application. Make sure to enable WiFi on your Device in the Shortcut Carousel. - Page 33 Notes...
- Page 36 For customer service and technical support, please contact American Technologies Network Corp. 1341 San Mateo Avenue, South San Francisco, CA 94080 phone: 800-910-2862, 650-989-5100 e-mail: service@atncorp.com www.atncorp.com ©2017 ATN Corporation...