Advertisement
Quick Links
Important Export Restrictions! Commodities, products, technologies and services contained in this manual
are subject to one or more of the export control laws and regulations of the U.S. Government and they fall
under the control jurisdiction of the US BIS-Department of Commerce. It is unlawful and strictly prohibited to
export, or attempt to export or otherwise transfer or sell any hardware or technical data or furnish any service
to any foreign person, whether abroad or in the United States, for which a license or written approval of the U.S.
Government is required, without first obtaining the required license or written approval from the Department of
the U.S. Government having jurisdiction. Diversion contrary to U.S. law is prohibited.
Advertisement
Related Manuals for ATN Daytime Series
Summary of Contents for ATN Daytime Series
- Page 1 Important Export Restrictions! Commodities, products, technologies and services contained in this manual are subject to one or more of the export control laws and regulations of the U.S. Government and they fall under the control jurisdiction of the US BIS-Department of Commerce. It is unlawful and strictly prohibited to export, or attempt to export or otherwise transfer or sell any hardware or technical data or furnish any service to any foreign person, whether abroad or in the United States, for which a license or written approval of the U.S.
-
Page 2: Mounting Rings
The information in this manual furnished for information use only, is subject to change without notice, is not to be construed as a commitment by ATN Corp. ATN Corp. assumes no responsibility or liability for any errors or inaccuracies that may appear in this book. ©2008 ATN Corp. All right reserved. -
Page 3: Battery Installation
• All glass multi-coated optics • Extra large objective lenses • Prosheild and Everlight Lens coatings • Sunshade * ATN reserves the right to change the above specifications at any time without notice OPeratING: Battery INstallatION: Figure 1 Install the battery into the housing with the polarity order as shown on the battery housing cap. - Page 4 (Fig.6). Figure 6 usING the atN raNGeFINder retIcle: The rangefinder reticle in your scope was designed to assist you in determining the range of your target. These distances are based on a 6’ target, if a 6’ target fits between the numbered baseline (the five short horizontal lines and the post of the reticle above the baseline determines your distance.
- Page 5 Upon initial use of the ATN Professional Variable Power scope you may notice a somewhat unusual behaviour of the reticle system. One, the reticle will increase or decrease with the power change. Two, the reticle will move from the center when you adjust windage and/or elevation. These are not defects.
-
Page 6: Installation
Most bases install with 6-48 screws and these should be torqued to about 22 inch/lbs. Generally all receiver/base combinations have some degree of misalignment. However, this is not a problem with the ATN rings as this is easily compensated for by the floating ring inserts, assuring a stress free scope/ mount/receiver combination, another important accuracy consideration. - Page 7 (it will void your warranty). If your scope ever does need any repair or adjustment, it should be returned to ATN’s service department. Optical surfaces will perform their best if they are wiped clean from time to time with a lens tissue or with optical quality lens paper like those for eyeglasses or camera lenses.
- Page 8 Base MOuNt FOr 12x36 Base Mount for 12x36 was developed for extreme range rifles like the 50 BMG. With 300 MOA of eleva- tion, ranging in access of 3000 Meters is possible. Used in conjunction with a scope internal adjust- ments there are three modes of vertical and two modes of horizontal adjustment.
- Page 9 Adjustment Compensator (BDC) Ring Your Scope and ATN LR Mount are now set for use. Properly used your scope’s reticle will now remain centered on its optical axis if the following shooting procedure is used. Normally only the vertical or elevation fine adjuster (internal scope) is used to fine-tune individual sight- ing.
- Page 10 Model 5x33L 5x33LU 2-6x40LU 3-9x55LU Magnification 2-6x 3-9x Objective Diameter 33 mm 33 mm 40 mm 55 mm 4° 4° 10°-3,2° 7°-2,2° FOV@100m(feet) 52.2-16.8 36.6-11.4 30 mm Rings 30 mm Rings 30 mm Rings 30 mm Rings Mounting ( included) (included) .223, .270, 30-06, 223, .270, 30-06,...
- Page 11 ATN, at its option, will ei- ther repair or replace the product, and such action on the part of ATN shall be the full extent of ATN’s li- ability, and the Customer’s sole and exclusive remedy. This warranty does not cover a product (a) used in other than its normal and customary manner;...
- Page 12 For customer service and technical support, please contact american technologies network Corp. north american office 1341 San Mateo Avenue, South San Francisco, CA 94080 phone: 800-910-2862, 650-989-5100; fax: 650-875-0129 European office phone: 44(0)870-0111286, fax: 44(0) 845-3349142 The following countries can use our toll free number 00 800 9102-8620 Austria, France, Germany, Holland, Italy, Spain, Sweden, Switzerland www.atncorp.com...