Table of Contents
Advertisement
Instruction
manual
To learn more about Porter-Cable
visit our website at:
http://www.porter-cable.com
Copyright © 2004 Porter-Cable Corporation
ESPAÑOL: PÁGINA 17
FRANÇAISE : PAGE 33
Double Insulated
Bayonet Saw
IMPORTANT
Please make certain that the person who is
to use this equipment carefully reads and
understands these instructions before
starting operations.
The Model and Serial No. plate is located on the main
housing of the tool. Record these numbers in the
spaces below and retain for future reference.
Model No. ______________________________________
Type ___________________________________________
Serial No. _______________________________________
MODEL 7549
Part No. 901015 - 08-09-04
Advertisement
Table of Contents
Related Manuals for Porter-Cable 7549
Summary of Contents for Porter-Cable 7549
- Page 1 Instruction manual To learn more about Porter-Cable visit our website at: http://www.porter-cable.com Copyright © 2004 Porter-Cable Corporation ESPAÑOL: PÁGINA 17 FRANÇAISE : PAGE 33 Double Insulated Bayonet Saw MODEL 7549 IMPORTANT Please make certain that the person who is to use this equipment carefully reads and understands these instructions before starting operations.
-
Page 2: Table Of Contents
Improper operation, maintenance or modification of tools or equipment could result in serious injury and property damage. There are certain applications for which tools and equipment are designed. Porter-Cable strongly recommends that this product NOT be modified and/or used for any application other than for which it was designed. -
Page 3: Safety Guidelines
SAFETY GUIDELINES - DEFINITIONS It is important for you to read and understand this manual. The information it contains relates to protecting YOUR SAFETY and PREVENTING PROBLEMS. The symbols below are used to help you recognize this information. indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. -
Page 4: General Safety Rules
GENERAL SAFETY RULES* Read all instructions Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. The term "power tool" in all of the warnings listed below refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. - Page 5 GENERAL SAFETY RULES* d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
-
Page 6: Additional Specific Safety Rules
ADDITIONAL SPECIFIC SAFETY RULES Hold power tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord. Contact with a "live" wire will make exposed metal parts of the tool "live"... - Page 7 SYMBOL ... volts ... amperes ... hertz ... watts ... kilowatts ... farads µF ... microfarads ... litres ... grams ... kilograms ... bars ... pascals ... hours ... minutes ... seconds ... no-load speed …/min or …min - ... Revolutions or reciprocations per minute or d.c.
-
Page 8: Carton Contents
MOTOR Many Porter-Cable tools will operate on either D.C., or single phase 25 to 60 cycle A.C. current and voltage within plus or minus 5 percent of that shown on the specification plate on the tool. Several models, however, are designed for A.C. -
Page 9: Functional Description
FUNCTIONAL DESCRIPTION FOREWORD Model 7549 Bayonet Saw is designed for cutting materials of the following MAXIMUM thickness: wood 2 SELECTING THE BLADE To obtain best results with your Porter-Cable bayonet saw, it is important that you use the right blade for the job. You will not only get better performance, but your blades will last longer and a smoother cut will result. - Page 10 5. Tighten blade screw approximately one turn and pull down on blade. Blade should not pull out of clamp. 6. Tighten blade screw securely. 7. Slide both blade guides, Fig. 1, towards blade until they lightly contact the sides of the blade, then back the guides off to produce paper thickness clearance per side.
- Page 11 INSTALLING PORTER-CABLE “HOOK” BLADES, steps 7 and 8. 6. To remove blade, loosen blade screw. NOTE: The clamp may be repositioned to accept Porter-Cable “Hook” blades by repeating steps 1 and 2 and positioning clamp as shown in Fig. 3. The clamp screw must be tightened securely when using “hook”...
-
Page 12: To Start/Stop Saw
Fig. 6 VARIABLE SPEED The 7549 is equipped with an adjustable variable speed control. The speed is adjusted by turning the control knob (A), Fig. 6. The control knob (A), Fig. 6, is numbered “1” through “6” with “1” being the slowest speed (approximately 500 SPM) and “6”... -
Page 13: Chip Blower
CHIP BLOWER This saw is equipped with a chip blower to keep the cutting area free of chips. This blower may be switched “ON” or “OFF” by moving lever (A), Fig. 8, to the “OPEN” position (blower “ON”) or the “CLOSED” position (blower “OFF”). - Page 14 If the work is large enough it can be held by hand across saw horses. The saw cuts freely with only light forward feed pressure on the tool. Forcing the saw will not make it cut faster.
-
Page 15: Troubleshooting
TROUBLESHOOTING For assistance with your tool, visit our website at www.porter-cable.com for a list of service centers or call the Porter-Cable help line at 1-800-487-8665. MAINTENANCE KEEP TOOL CLEAN Periodically blow out all air passages with dry compressed air. All plastic parts should be cleaned with a soft damp cloth. -
Page 16: Service
PORTER-CABLE LIMITED ONE YEAR WARRANTY Porter-Cable warrants its Professional Power Tools for a period of one year from the date of original purchase. We will repair or replace at our option, any part or parts of the product and accessories covered under this warranty which, after examination, proves to be defective in workmanship or material during the warranty period. -
Page 17: Español
Porter-Cable • Delta products should be obtained by contacting any Porter-Cable • Delta Distributor, Authorized Service Center, or Porter-Cable • Delta Factory Service Center. If you do not have access to any of these, call 888-848-5175 and you will be directed to the nearest Porter-Cable •...