N-Com B901 User Instructions And Safety
Hide thumbs
Also See for B901:
- User instructions (32 pages) ,
- Quick start manual (2 pages) ,
- Quick manual (2 pages)
Table of Contents
Advertisement
EN
USER INSTRUCTIONS AND SAFETY
Congratulations on your purchase of an N-Com product.
N-Com B901 was made using the most advanced technologies and the best
materials. Long-running tests and thorough system development have allowed
the highest audio quality to be achieved.
For additional information about B901 visit the website www.n-com.it
Firmware version:
REFERENCE STANDARDS
The products of the N-Com line are in compliance with standards as per the table below:
B901
Battery
charger
Battery
The Declarations of Compliance can be downloaded from the website www.n-com.it (Download
section).
FCC ID:
Y6MNCOM17
The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth
SIG, Inc. and any use of such marks by N-Com is under license. Other trademarks and
trade names are those of their respective owners.
1.0x
The Bluetooth system complies with the main safety requirements and
other applicable provisions of Directive 99/5/CE, Directive 2009/65/EC,
Directive 2011/65/CE, Directive 2012/19/EU
Directive 2006/95, 2004/108, 2009/65/EC, 2011/65/CE, 2012/19/EU,
2009/125/CE
Directive 2006/66/CE
IC:
9455A-NCOM17
R-NZ
B901 "S" - Fw 1.0x - 19/05/2017
Advertisement
Table of Contents
Related Manuals for N-Com B901
Summary of Contents for N-Com B901
- Page 1 Firmware version: 1.0x REFERENCE STANDARDS The products of the N-Com line are in compliance with standards as per the table below: The Bluetooth system complies with the main safety requirements and B901 other applicable provisions of Directive 99/5/CE, Directive 2009/65/EC,...
-
Page 2: Table Of Contents
10.1.Sharing music via Bluetooth ( A2DP Sharing ) ..................18 MUSIC VIA CABLE ..........................19 SATELLITE NAVIGATOR FOR MOTORCYCLES ................19 FM RADIO ............................19 N-COM INTERCOM (SERIES “900”) ....................20 14.1.Intercom pairing up ............................20 14.2.Intercom function (one-to-one connection) ..................20 14.3. Smart Conference (Group Intercom) ......................21 “UNIVERSAL INTERCOM”... -
Page 3: Warnings And Safety
WARNINGS AND SAFETY Read this User Manual carefully, as well as the User Manuals for other N-Com kits that you will be using with the N- Com B901. Read the simple rules listed below. Failure to comply with these rules may lead to dangerous situations. -
Page 4: Qualified Personnel
1.7. Disposal Refer to this user manual and to manuals related to other parts of the N-Com system in order to disassemble the system from the helmet. Once the system has been disassembled, dispose of it according to the following instructions: ... -
Page 5: Content Of The Packaging
CONTENT OF THE PACKAGING The N-Com B901 package contains: e-box B901 Electronic plate Microphone Rechargeable battery Battery charger PC connection Battery holder Key, screw, clamp Adhesive Velcro pads cable Microphone-Stop... -
Page 6: Installation
N-Com / Download section. Fig. 1 Fig. 2 Remove the “N-Com” protection plate located on the helmet shell (Fig. 1) and open the helmet chin guard (flip up helmets). Remove the right and left cheek pads from the ... - Page 7 (Fig. 4). Temporarily put the padding on the outside of the helmet (Fig. 5). Remove the N-Com cover from the helmet border gasket. Push from the inside of the helmet to facilitate the removal (Fig. 6).
-
Page 8: Installing The Microphone
B901 3.1. Installing the microphone JET HELMETS OR FLIP-UP HELMETS Fig. 9 Fig. 10 Prepare the microphone by inserting the microphone clamp, being careful to position it properly (Fig. 9) Note: the flat part of the clamp must be facing upward when the microphone is positioned as shown in figure 11. -
Page 9: Installing The System On The Helmet
3.2. Installing the system on the helmet Position the system inside the helmet as shown in figure 15, next to the N-Com housing in the shell. Fig. 15 Looking at the helmet from the outside, slide the rear positioning tab into groove A as shown in the figure;... - Page 10 B901 Insert the microphone connector in the micro USB electronic plate. Before you place the speaker in its housing, apply the Velcro pad to the polystyrene cheek pad (Fig. 19). Fig. 19 Fig. 18 Position the loudspeaker in the special ...
- Page 11 ONLY FOR JET HELMETS OR FLIP-UP HELMETS Secure the battery-holder support to the right side of the helmet, lining up the holes with the pins on the shell (Fig. 22) Fig. 22 ONLY FOR FULL FACE HELMETS Position the battery in the right polystyrene ...
-
Page 12: Removing The System
B901 Fig. 25 Fig. 26 Position the comfort padding in its housing (see specific instructions provided in the helmet user manual), hooking the neck roll (Fig. 25). Position both the comfort cheek pads in their housing (see specific instructions provided in the ... -
Page 13: Basic Functions
5.2. Auto On / Off function If the helmet does no move for more than 60 seconds, the B901 system goes into “deep sleep” mode. The system is completely turned on as soon as movement is detected. If the system is in “deep sleep” mode for more than 3 days, it turns off completely. To turn it back on, the “ON”... -
Page 14: Configuration Menu
B901 CONFIGURATION MENU All Bluetooth pair ups and other adjustments are carried out in this mode. To put the system in “Configuration mode” (starting from a switched off system) press the “ON” key and keep it pressed for 4 seconds, until the blue LED starts flashing quickly and you hear the voice announcement “... -
Page 15: Pairing Up With Mobile Phones Or Other Bluetooth Devices
Bluetooth device or by pressing “ON” and keep it pressed for about 2 seconds. MOBILE PHONE Per affiliare un telefono cellulare al sistema B901 seguire la procedura illustrata al Cap. 7. Answering a phone call Briefly press any key when you hear the incoming call signal. -
Page 16: Conference Call Function
8.2. Conference call function When a call comes in on a mobile phone connected via Bluetooth to B901, the intercom is temporarily turned off. However, if you wish to share the phone call with the other helmet, simply turn on the intercom manually during the phone call. -
Page 17: Managing Two Mobile Phones (Or Bluetooth Devices)
MANAGING TWO MOBILE PHONES (OR BLUETOOTH DEVICES) The B901 system can be hooked up to two phones (or Bluetooth) devices at the same time. The second phone (secondary device) can receive calls but not make them. To pair up the second Bluetooth phone (secondary device): Make sure the B901L is turned off;... -
Page 18: Music Via Cable
To pair up a satellite navigator to the B901 system, follow the procedure illustrated in Chapter 6. N.B.: Intercom connection is automatically cut off every time the navigator gives directions and restored at the end of the message from the navigator. -
Page 19: N-Com Intercom (Series "900")
Important: The procedure described below refers exclusively to the pairing up and operation between the B901 and the “900” series N-Com systems. To pair up to N-Com systems of a range other than the “900” series, please refer to the procedure described in chapter 15 “Universal Intercom”. -
Page 20: Smart Conference (Group Intercom)
B901 The VOX function is disabled by default on the device. N.B.: In case the pre-setting position is empty, or the system being called cannot be reached within the maximum range or it is already engaged in a phone call, you will hear an error voice message. -
Page 21: Universal Intercom" Intercom
Caution: Visit the www.n-com.it website for the list of compatible N-Com systems. 15.1. Pairing up the UNIVERSAL INTERCOM The N-Com system can be paired up to the other intercom (from now on referred to as Intercom B) as if it was a mobile phone. Make sure the B901 is turned off;... -
Page 22: Universal Conference (Chain Intercom)
The “Universal Conference” mode can be used to connect in conference call N-Com systems of the “900” series and one system paired up in Universal Intercom mode. N.B.: This mode can also be used by connecting only N-Com “900” series systems, in alternative to the “Smart Conference” mode (chapter 14.3). - Page 23 The three systems are not in intercom conference call mode and can talk to each other at the same time. All intercom conference call systems can be disconnected by briefly pressing the “ON” command on any one of the devices connected in conference call. In case you wish to add another system (D), the latter must be paired up beforehand to system C.
-
Page 24: Remote Control
B901 16. REMOTE CONTROL The B901 device can be controlled through a remote control (sold separately), thus avoiding the need to take your hands off the handlebars to use the keyboard. Please refer to the specific operating instructions of the Remote Control in order to use its various functions. -
Page 25: Summary Table Of Controls
18. SUMMARY TABLE OF CONTROLS Button Turning on 2 sec Turning off 3 sec Increase Volume Decrease Volume Answer phone call* Voice call 2 sec Speed Dialling Menu ** Hang up/reject a phone call 2 sec Manual Device Connection 2 sec Phone Conference Activation... - Page 26 Pairing up CHANNEL 2 (“900” series) Pairing up CHANNEL 3 (“900” series) Reset *Press any key on the N-Com keypad. **Press the keys at the same time. ***All the Setting functions must be carried with the system in Setting Mode.
-
Page 27: Limited Warranty
Any damage caused by an accident; Any change or modification made to the helmet or to the N-Com system by the user or by third parties. Color changes or damages caused by exposure to harmful chemical products. -
Page 28: Validity Of This Limited Warranty
This warranty does not affect the consumer’s rights provided for by the law, and specifically by the provisions of Legislative Decree 2 February 2002 n. 24. 19.5. Product identification N-Com products are identified by means of a code that allows product traceability and identification. The identification code is printed on the adhesive label applied to the B901 system. -
Page 29: Warranty Registration Form
20. WARRANTY REGISTRATION FORM Product name B901 Identification code Buyer’s Information Name Last name Address Phone e-mail Dealer’s stamp Date of purchase... - Page 30 Certification and Safety Approvals FCC Compliance Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
- Page 31 aux instructions, il peut occasionner des interférences nuisibles au niveau des communications radios. Cependant, il n’existe aucune garantie que ces interférences ne se produiront pas dans une installation particulière. Si cet équipement génère des interférences nuisibles à la réception de la radio ou de la télévision (ce qu’il est possible de déterminer en mettant l’équipement hors tension, puis sous tension), l’utilisateur est invité...
- Page 32 (5) Industry Canada(IC) Statement Industry Canada(IC) Statement This device complies with RSS This device complies with RSS- - 210 of the Industry Canada Rules. 210 of the Industry Canada Rules. Operation is subject to the following two conditions: Operation is subject to the following two conditions: 1) this device may not cause interference and 1) this device may not cause interference and 2) this device must accept any interference.
- Page 33 IC Radiation Exposure Statement: IC Radiation Exposure Statement: This equipment complies with IC radiation exposure limits set forth for an This equipment complies with IC radiation exposure limits set forth for an This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment.