Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for N-Com B4
Summary of Contents for N-Com B4
- Page 1 USER INSTRUCTIONS AND SAFETY Firmware Version: 3.1x...
- Page 2 For additional information about B4, and to download high-definition instructions as well as the latest Firmware version, visit the website www.n-com.it REFERENCE STANDARDS The products of the N-Com line are in compliance with standards as per the table below: Bluetooth system...
-
Page 3: Table Of Contents
1.6.Accessories and batteries ............5 1.7.Disposal ................6 CONTENT OF THE PACKAGING ..........6 INSTALLATION ..............7 3.1.Removing the B4 system from the helmet......... 9 BASIC FUNCTIONS............. 10 4.1.System menu..............10 N-COM WIZARD ..............11 PAIRING UP BLUETOOTH DEVICES ........11 6.1.Affiliation reset function ............12... -
Page 4: Warnings And Safety
Read this User Manual carefully, as well as the User Manuals for other N-Com kits that you will be using with the N-Com B4. Read the simple rules listed below. Failure to comply with these rules may lead to dangerous situations. -
Page 5: Qualified Personnel
Carry out all operations on the electronic equipment and on the N-Com system with the vehicle stopped, in compliance with Traffic Regulations. Caution: B4 allows radio reception. Any radio licence fees are to the user’s charge. 1.5. Qualified personnel Only qualified personnel can carry out technical assistance on this product. -
Page 6: Disposal
1.7. Disposal Refer to this user manual and to manuals related to other parts of the N-Com system in order to disassemble the system from the helmet. Once the system has been disassembled, dispose of it according to the following instructions: The presence of a crossed-out wheelie bin indicates that in the European ... -
Page 7: Installation
(Fig.1) Fig. 1 Before you install the B4 system on the helmet, make sure it turns on properly. Press the “on” key for about 2 seconds, until the LED lights up and you hear a beep in the headset. - Page 8 (Fig. 6). Caution: make sure that the side of the microphone support with the writing “N-Com” is facing inward. Fig. 6...
-
Page 9: Removing The B4 System From The Helmet
Unhook the right and left clips from the shell, levering upward using a flat head screw (or a similar tool), as shown in figure 9. Fig. 9 Completely remove the B4 system from the helmet and re-install the cheek padding and the gasket. -
Page 10: Basic Functions
A special acoustic beep signals the change from one function to another. When B4 is turned on, the menu is always in the “BASE” mode. Depending on the menu position, you can manage the various audio devices and the available functions:... -
Page 11: N-Com Wizard
Select the N-Com device. If a password is requested, enter 0000 (four zeros); B4 will confirm the pairing up by means of a tone in the headset, and the LEDs will stop flashing; Turn off and on both the mobile phone and the B4 to store the pairing up data. -
Page 12: Affiliation Reset Function
B4 allows a conference call with Rider and Pillion Passenger. When a call comes in on a mobile phone connected via Bluetooth to B4, the Rider-Pillion Passenger intercom is temporarily turned off. However, if you wish to share the phone call with the other helmet, simply turn on the intercom manually during the phone call (by briefly pressing “on”). -
Page 13: Stereo Fm Radio
(among the pre-set ones) 10. BLUETOOTH A2DP MUSIC PLAYER You can listen to high quality music by connecting B4 to a device equipped with Bluetooth A2DP (Advanced Audio Distribution Profile) protocol. The B4 system is also equipped with Bluetooth AVRCP (Audio Video Remote Control Profile) protocol, which allows you to stop and resume music reproduction directly from the helmet (with devices equipped with AVRCP). -
Page 14: Audio Devices With Cable Connection
A2DP or via RADIO. 12. RIDER-PASSENGER INTERCOM MODE In order to use B4 in wireless intercom mode, both helmets have to be equipped with a Bluetooth kit. In order for two Bluetooth Kits to communicate with one another, they have to be paired up first. -
Page 15: Bike-To-Bike Intercom
N.B.: The range of the communication varies depending on the N-Com systems used. The B4 system stores up to 4 different B4 systems, so that “calls” can be made to these devices. So that two B4 systems can communicate with one another in the Bike-to-Bike mode, they must be paired up first. -
Page 16: Taking A Bike-To-Bike Call
The search for automatic reconnection lasts 2 minutes, at the end of which reconnection must be carried out through the “Bike-to-Bike Call”. For additional information, please visit the website www.n-com.it... -
Page 17: Battery
14.2. Recharging the system To recharge the B4 system, connect the USB cable to a battery charger or to a powered USB port. Charging occurs as follows: When you connect the B4 system to the battery charger, the blue LED begins to flash. -
Page 18: Summary Table Of Controls
15. SUMMARY TABLE OF CONTROLS Button Pressure Brief Long Brief Long Brief Long Brief Long Turning on (2s) Turning off (5s) Increase Volume Decrease Volume Scroll menu (Base, Radio, Bike to Bike) (2s) Answer phone call Voice call... - Page 19 Bike 1 pair up (2s) Bike 2 pair up (2s) Bike 3 pair up (4s) Bike 4 pair up (4s) Bike-to-Bike menu enabling/disabling Erase pair ups** (4s) Briefly press at the same time. **With N-Com system in Pairing up Mode.
-
Page 20: Limited Warranty
Negligence and normal wear of internal and external parts. Any damage caused by an accident; Any change or modification made to the helmet or to the N-com system by the user or by third parties. Colour changes or damages caused by exposure to harmful chemical products. -
Page 21: Validity Of This Limited Warranty
Moreover, the defects covered by this warranty do not include all those specific and subjective situations that may come up during the active use of the helmet such as, for example, comfort problems while riding or aerodynamic noises. Nolangroup shall not be held responsible in any case for incidental or consequential damages (including, without any limitation whatsoever, damages to one or more persons) resulting from non-fulfilment of the obligations arising from this warranty as it pertains to Nolangroup products. -
Page 22: Product Identification
This warranty does not affect the consumer’s rights provided for by the law, and specifically by the provisions of Legislative Decree 2 February 2002 n. 24. 16.5. Product identification The identification code is printed on the adhesive label applied to the B4 system, under the rechargeable battery. -
Page 23: Warranty Registration Form
17. WARRANTY REGISTRATION FORM Product name Identification code Buyer’s Information Name Last name Address Phone e-mail Dealer’s stamp Date of purchase... - Page 24 B4 - 05/03/2013 10:17:00 Printed on recycled paper...