Set (Menu) Mode - Yaesu FT-65R/E Operating Manual

The FT-65R/E Set Mode, already described in parts of many previous chapters,
is easy to activate and set. It may be used for configuration of a wide variety of
transceiver parameters, some of which have not been detailed previously. Use
the following procedure to activate the Set Mode:
1. Press the F/W key, then press the [ 0 SET] key to enter the Set mode.
2. Press [▲] [▼] key to select the Set Mode Item to be adjusted.
3. Press the F/W key momentarily to enable adjustment of the Set Mode Item.
4. Press [▲] [▼] key to adjust or select the parameter to be changed on the
Set Mode Item selected in above step.
5. After completing your selection and adjustment, press the PTT switch mo-
mentarily to save the new setting and exit to normal operation.
No. ITEM Function
1 APO Auto power off
2 ARTS Setting the ARTS function.
ARTS BEEP function type.
ARTS Polling time (Interval)
3 BATTSAVE Selects the Receive-mode Battery
Saver interval ("sleep" ratio)
4 B-CH.L/O Busy Channel Lock-Out
5 BEEP Beep function Enable/Disable
6 BELL Select the number of CTCSS/DCS
Bell ringer repetitions.
7 COMPANDER Voice Compander
8 CTCSS Setting the CTCSS Frequency TX
and RX
9 CW ID CW identifier during ARTS
operation. Transmission every 10
minutes.
10 DC VOLT Indicate Battery DC Voltage.
11 DCS CODE Setting the DCS CODE TX and
RX
12 DTMF SET Setting the DTMF autodialer
sending delay time and Speed and
Delay time.
13 DTMF WRT Programing to DTMF autodialer.
14 EDG.BEEP Enables/Disables the Band-
edge beeper while selecting the
frequency via the [▲] or [▼] key.
15 KEY LOCK Keyboard Lock function
16 LAMP Selects the LCD/Keypad Lamp
mode.
17 LED Selects the active or disable TX/
BUSY LED function.
18 MEM DEL Delete Memory Channel mode
19 MON/T-CL Selects the MONI switch function. MONI / T-CALL1750 / T-CALL2100
20 NAME TAG Stores Alpha-Numeric "Tags" for
the Memory channels.
FT-65R/E Operating Manual
FCC ID: K6620665X20 / IC: 511B-20665X20
s (M
et
Values
OFF/0.5H to 12.0H (Step 0.5H)
BEEP= INRANGE / ALWAYS /
OFF
INT= 25sec / 15sec
200 mS / 300 mS /500 mS / 1
SEC / 2 SEC / OFF
B-CH.L/O ON / B-CH.L/O OFF
KEY+SC/KEY/OFF
OFF / 1Time / 3Times/ 5Times /
8Times / CONTINUE
CMP.ON / CMP.OFF
50 CTCSS tones and OFF
TX= ON/ OFF
ID=****** (6cara)
104 DCS CODEs
MODE= Manual / Auto
Delay= 50mS / 250mS / 450mS /
750mS / 1000mS
Speed= 50mS / 100mS
BEEP OFF / BEEP ON
KEY / PTT / P+K
5secKEY / 10secKEY / 30secKEY
/ CONT / OFF
TX= ON / OFF
BUSY= ON/ OFF
Select Delete memory
/ T-CALL1000 / T-CALL1450
Application for FCC / IC
) M
enu Ode
Default Value
OFF
ARTS=OFF
INT= 25Sec
200mS
OFF
KEY+SC
OFF
OFF
TX=OFF
RX=OFF
TX= OFF
ID= blank
TX=OFF
RX=OFF
M=Manual
D=450mS
S=50mS
BEEP OFF
KEY
5secKEY
TX=ON
BUSY=ON
MONITOR
-
25