Video Select; Adjusting The Brightness Of The Display (Dimmer) - Pioneer VSX-D2011-G Operating Instructions Manual

Basic Operation

Video Select

This function allows you to listen to one sound source while you watch a different video source on your TV. The
sound source is set in the normal fashion as explained on page 44 You then change the video input with the
VIDEO SEL button.
S0URCE
DVD/LD
VCR2
CD-R/
TAPE1
DIMMER
1
SIGNAL SEL
5
2
VIDEO SEL
9
SYSTEM SETUP
MENU
TUNER EDIT
AUDIO
MPX
¶
TUNING
1
STATION
4
CHANNEL

Adjusting the Brightness of the Display (DIMMER)

Use the display DIMMER button to adjust the brightness of the fluorescent display.
S0URCE
DVD/LD
VCR2
CD-R/
TAPE1
2
DIMMER
1
SIGNAL SEL
5
VIDEO SEL
9
SYSTEM SETUP
MENU
TUNER EDIT
AUDIO
56
En
SETUP
TV SYSTEM RECEIVER
OFF
VCR1/
TV/SAT TV CONT
DVR
MULTI CONTROL
MULTI
VIDEO CD
OPERATION
1
MD/
TUNER RECEIVER
TAPE2
LOUDNESS TONE EFFECT/CH SEL
2 3 4
+
DNR BASS/TREBLE
6 7 8
–
+
HI-BIT 10 DISC
0
ENTER
DIRECT ACCESS SEARCH MODE
GUIDE
TOP MENU
TRACK
ENTER
EXIT
RETURN
TEXT ON RF ATT DISP MODE
8
SUB TITLE
– +
BAND TUNING
3 ¡
– +
TEXT OFF CLASS STATION
7 ¢
– +
CHANNEL
SETUP
TV SYSTEM RECEIVER
OFF
VCR1/
TV/SAT TV CONT
DVR
MULTI CONTROL
MULTI
VIDEO CD
OPERATION
1
MD/
TUNER RECEIVER
TAPE2
LOUDNESS TONE EFFECT/CH SEL
2 3 4
+
DNR BASS/TREBLE
6 7 8
–
+
HI-BIT 10 DISC
0
ENTER
DIRECT ACCESS SEARCH MODE
GUIDE
TOP MENU
TRACK
ENTER
EXIT
RETURN
1 Press RECEIVER.
2 Press the VIDEO SEL button on the
remote control to cycle through the
different possible video inputs.
The first press shows the video input you are currently
using. After that pressing VIDEO SELECT cycles though
the possibilities in the following order:
DVD/LD
OFF
VCR2
The OFF setting means you are listening without a
video signal. (Also, when you select CD, CD-R/TAPE1,
MD/TAPE2, TUNER, PHONO, USB or functions the
VIDEO SELECT will be set to off.)
After choosing a video input the display on the receiver
will show that input for about 5 seconds and then
revert to showing the listening mode the receiver is in.
• The VIDEO SELECT remains set to the input you
memo
chose until you change the audio input.
• If you change audio functions the receiver will
reset itself to make the video and audio inputs
correspond.
Also, if you switch the power of the receiver off
when you turn it back on the video and audio in-
puts will reset so that they correspond.
1 Press RECEIVER.
2 Use the display DIMMER button on
the remote control to alternate
between the different levels of
brightness for the display.
Four levels of brightness ranging from very dim to very
bright can be selected. Each press changes the
brightness of the display. When cycling through the
options, the default brightness can also be selected.
memo
It is a feature of this unit that the fluorescent dis-
play will be brighter for a few seconds after you
choose a function (like DVD/LD, CD, etc.) and then
get softer. This will still happen when you adjust
the brightness but the new setting will be the one
the display softens to.
VIDEO
TV/SAT
VCR1/DVR