Controlling The Rest Of Your System; Setting The Remote To Control Other Components; Selecting Preset Codes Directly; Programming Signals From Other Remote Controls - Pioneer VSX-82TXS Operating Instructions Manual

Controlling the rest of your system

Chapter 11:
Controlling the rest of your system
Setting the remote to control other
components
Most components can be assigned to one of the input
source buttons (such as DVD/LD or CD) using the
component's manufacturer preset code stored in the
remote.
However, there are cases where only certain functions
may be controllable after assigning the proper preset
code, or the codes for the manufacturer in the remote
control will not work for the model that you are using.
If you can't find a preset code that matches the
component you want to control, you can still teach the
remote individual commands from another remote
control (see Programming signals from other remote
controls below).
Note
• You can cancel or exit any of the steps by pressing
RECEIVER. To go back a step, press RETURN.
• After one minute of inactivity, the remote
automatically exits the operation.

Selecting preset codes directly

SYSTEM OFF
RECEIVER INPUT SOURCE
SELECT
CD TV VIDEO 2
DVD SAT VIDEO 1 TV CONT
DVR2 CD-R XM RADIO ROOM2/3
DVR1 i Pod TUNER RECEIVER
1 While pressing the RECEIVER button, press SETUP .
The remote LCD display shows SETUP.
2 Use to select PRESET then press ENTER .
3 Press the input source button for the component
you want to control then press ENTER .
The LCD on the remote displays the component you want
to control (for example DVD or VIDEO 1).
Note
1 You can't assign the RECEIVER, TUNER, iPod or XM RADIO buttons.
2 • When using a Pioneer HDD recorder, please select PIONEER DVR 487, 488, 489 or 493.
• When using a Pioneer plasma display released prior to summer 2005, please select preset codes 637 or 660.
3 The remote can store about 200 preset codes (this has been tested with codes of Pioneer format only).
4 • You can't assign the RECEIVER, TUNER, iPod or XM RADIO buttons.
• TV CONTROL buttons (TV ,TV VOL +/–, TV CH +/– and INPUT SELECT) can only be learned after selecting TV CONT.
D.ACCESS CLASS
+10 DISC
ENTER
AV PARAMETER CH LEVEL
TOP MENU MENU
TUNE
ST ST T.EDIT
DTV MENU
ENTER
RETURN
SETUP
TUNE
CATEGORY
BAND
GUIDE
TV CONTROL
INPUT
TV VOL TV CH VOL
SELECT
1
4 Use to select the first letter of the brand name
of your component then press ENTER .
This should be the manufacturer's name (for example, P
for Pioneer).
5 Use to select the manufacturer's name from
the list then press ENTER .
6 Use to select the proper code from the list,
then try using this remote with your component.
The code should start with the component type (for
example, DVD 020). If there is more than one, start with
2
the first one.
To try out the remote control, switch the component on or
off (into standby) by pressing SOURCE
seem to work, select the next code from the list (if there
is one).
• If you can't find or properly enter a preset code, you
can still teach the remote individual commands from
another remote control (see Programming signals
from other remote controls below).
7 If your component is controlled successfully, press
ENTER to confirm.
The remote LCD display shows OK.
Programming signals from other
remote controls
If the preset code for your component is not available, or
the available preset codes do not operate correctly, you
can program signals from the remote control of another
component. This can also be used to program additional
operations (buttons not covered in the presets) after
3
assigning a preset code.
1 While pressing the RECEIVER button, press SETUP .
The remote LCD display shows SETUP.
2 Use to select LEARNING then press ENTER .
The LCD on the remote prompts you for the component
you want to control (for example DVD or VIDEO 1).
3 Press the input source button for the component
you want to control then press ENTER .
PRES KEY shows in the LCD display.
11
. If it doesn't
4
71
En