Table of Contents
Advertisement
(0
SET-UP FOR MONITOR
INSTALLATION
When installing the monitor, make set-up adjustments required for the picture settings to
match conditions where the monitor is to be used.
To call up SET-UP MENU and select a function: ---
1.
To
make
[I] (SET-UP MENU) appear, with the ENTER button pressed,
press the MENU button.
2.
Press the
J. or T button to select an adjustment rtem.
(To set STATUS DISPLAY or CONTROL LOCK, steps
3
and
4
are not
necessa,y.)
3.
Press the ENTER button to call up the adjustment menu
[I]
of a selected
item (e.g. WHITE BALANCE).
4.
Press the
J. or T button to select a function to be adjusted.
5.
Press the
<I
or "'" button to change the setting.
6.
With the display
[I]
on screen, press the
J. or T button to select another
function and repeat step
5.
7.
Press the MENU button to complete. SET-UP MENU disappears.
• To make
[I] (SET-UP MENU) disappear:
Pcess the MENU button.
e
To make
[I]
(e.g. WHITE BALANCE) disappear:
Press the MENU button twice.
SIZE/CENTERING
(size/positioning
adjustments
of RGB signal pictures)
--
For analog RGB video signal pictures, horizontal size, vertical size,
horizontal positioning and vertical positioning can be finely adjusted.
Adjustment (level)
Function
H. POSITION (-10, -9 ... 0 ... +9, +10)
+
moves the picture to right.
- moves the picture to left
V. POSITION (-10, -9 ... 0 ... +9, +10)
+ moves the picture down.
- moves the picture up.
H. SIZE (-10, -9 ... 0 ... +9, +10)
+
makes the picture wider.
- makes the picture narrower.
V. SIZE (-10, -9 ... 0 ... +9, +10)
+
makes the picture higher.
- makes the picture lower.
<SET-UP MENU>
SIZE/CENTERING
l>WHITE
BALANCE
ADJUST
REMOTE SELECT
STATUS
DISPLAY:ON
CONTROL
LOCK
: OFF
l!ll!!!!!!l
:1:1
[I]
<
WHITE BALANCE)
I>
RED ORIVE
: 0
GREEN
DRIVE
: O
BLUE
DRIVE
:
0
RED CUTOFF
: 0
GREEN CUTOFF
: 0
BLUE CUTOFF
: 0
lllliiw
:l:l
s
II]
• Each time the MENU button is pressed,
the previous menu is restored.
s
• SIZE/CENTERING
appears and the
function
is operable
only when
monitoring the picture of analog RGB
\lldeo signals.
SET-UP FOR MONITOR INSTALLATION (continued)
WHITE BALANCE ADJUST (white balance adjustments) --
Before making these adjustments, select the color temperature
9300K or 6500K on MENU.
Adjustment (level)
Function
RED DRIVE (-10, -9, ... 0 ... +9, +10)
Adjusts the drive level of a red signal
component.
GREEN DRIVE (-10, -9, ... 0 ... +9, +10)
Adjusts the drive level of a green
signal component.
BLUE DRIVE (-10, -9, ... 0 ... +9, +10)
Adjusts the drive level of a blue signal
component.
RED CUTOFF (-10, -9, ... 0 ... +9, +10)
Sets the cut-off voltage of a red signal
component.
GREEN CUTOFF (-10, -9, ... 0 ... +9, +10)
Sets the cut-off voltage of a green
signal component.
BLUE CUTOFF (-10. -9, ...
O •.
+9, +10)
Sets the cut-off voltage of a blue
signal component
REMOTE SELECT {TALLY/REMOTE-terminal
settings) --
Via the TALLY /REMOTE terminal, the tally lamp can be
turned on/off, or a function (selected from display
III
shown
on the right) can be operated using an external control.
INPUT setting indications and selected inputs
s
• By making white balance
adjustments on SET-UP MENU,*
appears to the right of the
COLOR
TEMP.
setting on
MENU
(see page 7).
<REMOTE SELECT>
lo-INPUT
:AHB
CNTL • 1 :
UNDER
SCAN
CNTL-2
:ASPECT RATIO
[leliw
:l:l
rn
*=
indicates when deactivating
the remote
control via
the
TALLY/REMOTE terminal
~":,INOTUSE
A<->8
AHY/C
IA~RGB
IA,E.~COMPOI BHVIC
IBoRGB
IBHCOMPO
I
YICHRGB
I
Y/C4---)COMPO IRGBttCOMPO
......
C,,.•
-·
*
A
YIC
RG8
COMPO.
YIC
RGB
CNTL-1/CNTL-2
setting indications and set positions
Y/C
YIC
RG8
COMPO.
RGB
COMPO.
COMPO.
*=
indicates when deactivating the remote control
via
the TALLY/REMOTE terminal
Setting
indication
NOT USE \UNDER SCAN
I
PULSE CROSS
j
COLOR OFF
I
BLUE CHECK \EXTERNAL SYNC
I
ASPECT RA
no I
COLOR TEMP.\ AUDIO MUTE
Short-circuit
*
ON
ON
ON
ON
External
Open-circuit
OFF
OFF
OFF
OFF
Internal
eTALL Y/REMOTE terminal functions
All controls via TALLY/REMOTE terminal are made by short-circulting or open-circuiting
any pin from Pin 1 to 4 and either Pin 7 or 8 (GND each) of this terminal.
When using this terminal, be sure to short-circuit Pin 5 and either Pin 7 or 8.
To~ult
0
~'-C"C-=---
16-9
6500
ON
4.3
9300
OFF
s
e
When
the TALLY/REMOTE terminal
is
used,
the
following functions
become deactivated (except 'Mlen
they are set to 'NOT USE"):
- Front INPUT SELECT
and
EXT
SYNC switches
- Front UNDER SCAN, PULSE
CROSS, COLOR OFF and BLUE
CHECK switches
-~screen
MENU's
ASPECT RATIO
am
COLOR TEMP.
functions
- Remote MUTE key
e
It
a
function
is
applied to
both
CNTL-1
and
CNTL-2, CNTL-1
has
priority.
OJ
-;i
s
....
cc
01
C
-<
Hide quick links:
Advertisement
Chapters
Table of Contents
