Panasonic BT-M1950Y Service Manual page 8

CD
MEMORY MODE
A set of picture settings can be programmed in memory
for quick recall when necessary.
Recall/release of memory mode ---------
Press the MEMORY MODE switch to recall a set of picture settings
programmed in memory.
Pressing the switch locks the functions of the front-panel PHASE,
CHROMA, BRIGHT, and CONTRAST controls
not
to be operated.
Press again to release memory mode.
Setting programming of the picture being monitored -
The settings of the picture being monitored can be programmed in
memory.
Settings programmable in memory mode;..: -----------~
e
Settings of the CONTRAST, BRIGHT, CHROMA and PHASE controls on the
front panel
• On-screen menu function settings (except RGB/COMPONENT)
1.
Check the MEMORY MODE switch is off.
2.
Press the MENU button.
3.
Press the .ti. or T button to select MEMORY MODE.
Then press the ENTER button.
4. •
Press the ENTER button to program.
• Press the
<Ill
or .,_ button to cancel.
Revision
of
memory mode-----------
Programmed picture settings can be revised ff necessary.
1.
Press the MEMORY MODE switch to activate memory mode.
2.
Press the MENU button to call up display [I] on screen.
e
• If you attempt to operate a locked
function, "MEMORY MODE ON!!"
appears on screen
for approx.
2
seconds
to
indicate 1he function
cannot be
operated.
e
• Programmed picture settings are
kept in memory after the power is
tumedoff.
<MEMORY MODE)
Ara you sure?
"Yes~ then
!!ml
"No"'
thenllorll
e
• No matter
what
video signal is input,
all items appear on screen.
However, depending on 1he type of
input video signal, some
functions
rright not operate even H their
settings are made.
<MEMORY MODE REV I SE>
.. p ICTURE ADJUSTMENT
ASPECT RATIO
:4-3
FI L
TER SELECT :COIIB
PEAK I
NG
FREQ. :2.IIMHZ
PEAKING LEVEL :OdB
AFC :NORMAL
COLOR TEMP. :6500
NTSC SETUP :0
COMPO. LEVEL :SMPTE
~- =•
[i]
MEMORY MODE (continued)
3.
Press the .ti. ·or T button to select a function to be revised.
Press the ENTER button after selecting PICTURE ADJUSTMENT to call up
display
00.
After making all settings on screen, press the MENU button to make display
[i] appear.
4.
Press the
<111
or.,_ button to change the set level.
Adjustable CONTRAST, BRIGHT, CHROMA or PHASE range depends on
each set level previously stored in memory. MAX appears to indicate maximum
level that cannot be increased. MIN appears to indicate minimum level that
cannot be decreased.
evariable
setting range
Function Variable setting range Initial (default) setting
PICTURE
CONTRAST -2010+20 0
ADJUST-
BRIGHT -2010 +20 0
MENT
CHROMA -20 lo +20 0
PHASE -20to+20
0
ASPECT RATIO 4:3 16:9 4:3
FILTER SELECT COMB BOTH NOTCH COMB
PEAKING
FREQ. 2.6MHz 5.0MHz 2.6MHz
PEAKING LEVEL OdB+ldB ··· +9dB OdB
AFC NORMAL
FAST SLOW NORMAL
COLOR TEMP. 9300 6500 6500
NTSCSETUP 0
7.5
0
COMPO. LEVEL SMPTE BETAOO BETA7.5 SMPTE
5.
Wrth display [I] on screen, press the MENU button to make display
00
appear.
ePress the ENTER button to program.
ePress the
<Ill
or"'" button to cancel.
<MEMORY MODE REV I SE>
.. CONTRAST : D
BRIGHT :0
CH~ :0
PHASE :0
IBD
:1:1
rn
e
e
111he ENTER button
Is
pn,ssed
-r
a function o1her than PICTURE
ADJUSTMENT Is
selected,
1110
on-
screen display changes
into
a
single--line one. To select another
function after
making
a change in
function, press 1he MENU button to
restore display (Il.
• When 1he
monitor was
shipped from
1he factory, 1he NTSC SETUP had
been set to 7.5 and the COMPO.
LEVEL to BETA 7.5.
<MEIIORY MOOE REVISE>
Are you sure ?
·y .. • then
Im
"No" lllenl!lor
8
00
m
~
3:
..a.
co
en
0
<