Panasonic BT-M1950Y Service Manual page 11

BEFORE CALLING FOR SERVICE
Before concluding a problem has occurred, check the following points. If the problem
persists after carrying out the checks, disconnect the power cord from the AC outlet and consult
the dealer from whom you purchased the monitor.
Problems Points to be checked
Measures
Inoperable adjustment controls or Is MEMORY MODE switched on? Switch off.
buttons.
Is CONTROL LOCK activated? Deactivate It.
Abnormal picture adjustments with Are PICTURE ADJUST menu Reset to standard settings.
all controls at center. settings changed via remote
control?
Inoperable picture synchronization. Is EXT SYNC switched on? Switch to off.
No sound via audio signal input. Does the audio input tenninal Each audio input tenninal is linked
match the video input tenninal? with a video input tenninal.
No INITIALIZE MENU display. Are you pressing the T and Keep pressing these buttons until it
MENU buttons until It appears? appears.
Inoperable CNTL·2·extemal control Is a function applied common to Set other functions to CNTL-2.
via TALLY/REMOTE tenninal. CNTL-1 and CNTL-2?
MENU DISPLAY CHART
The initial (default) adjustments/settings are shown in the menus below.
When the monitor was shipped from the factory, the NTSC SETUP had been set to 7.5 and
the COMPO. LEVEL to BETA 7.5.
MENU
Menu functions
<MENU>
rarr ming
.-ASPECT RAT 10 :4-3
FI L TER SELECT :COMB
<IEIIOAY UOOE>
PEAK ING FREQ. :2.IIIHZ
PEAK ING LEVEL :GdB
ENTER
Anoyou-1
AFC :NORMAL
COLOR TEMP. :6500
:::-·=m
NTSC SETUP
,o
COMPO. LEVEL :SMPTE
<MElla:IY MODE>
RGBtCOMPONENT :RGB
111!!!!!!1
'"'
MEMORY MODE+ MENU-------------MENU
ENTE
.... +
.... +
Memory-Mode revision menu
I
Memory-Mode picture adjustments
<IEMORY .a>£ REVISE>
•:~~~g;e R:~1gsr~:
-+1------i1111'~11
ENTER-..
<MEMORY MOOE Rl!YIS!)
.. COHTRAST : 0
BRIGHT :O
FIL TEA SELECT :COMB
PEAK I NG FREQ. :2.IUHZ
PEAKING LEVEL :OdB
AFC :NORMAL
COLOR TEMP. :6500
NTSC SETUP :0
ctllPO. LEVEL :SIIPTE
!liiiiil ...
R+ MENU
Set-up for monitor installation
<SET-I.IP MENU>
... SIZE/CENTERING
WHITE BALANCE ADJUST-
REMOTE SELECT
STATUS DISPLAY:ON
CONTROL LOCK :OFF
l!liiiil
,..,
MENU
Menu-function resetting
._.,,....,
Anlyoa-?
::,·::m
MENU+POWER
"Initialize" menu
C INITIALIZE MENU>
IDNllmlRseT
11-<IET·UP IENU>RESET
!11111
ENTER ... ...
-
ENTER~
~
ENTER ...
...
ENTER-..
r
CHll0MA :0
PHASE :0
lllll :e
RGB-signat picture
size/poshioning adjustments
<SIZl/CINttR ING>
-.H. POSITION
,o
Y, POSITION
,.
H.SIZI!
,,
Y, SIZI!
,o
illllll
,
..
1ents White-balanoe adjustme
<WHITE BALANCE.>
.. REDDNYE
,o
GREENDRMI
,,
IIUIIDRIYE
,,
REDCUJOl'F
,o
GR!.l!N CUTOFF :
o
BLlll!CUTOFF
"
111111
,
..
Remote-tanninal settim s
CR&IOf& SILECT>
"'INPUT :NOT USE
CNTL•1 :NOT USE
CNTL•2 :NOT USE
!11111
,.
Menu-function standan:faza.tion
Cla'.U-_,>RESET
AnyoulUN?
-::;·::Pe
Memory-Mode revision
<l&IIOfrf MOOERE\1112>
MyouMn'I
:~·=i!a
Ul
7
:s: ...
cc
01
0
-<