Emerson Oxymitter 5000 Instruction Manual page 124

Parameter Mnemonic Valid Range
± INF
COLD_JUNC_MV_
VALUE
COLLECTION_
DIRECTORY
CONFIG_CHANGED 0-255
TB_DETAILED_ 0-16777215
STATUS
HIGH_CASE_TEMP 0-10000.0
HIGH_CASE_TEMP_ 0: No effect
RESET
1: Reset high
case
temperature
IO_PIN_MODE See table 2
IO_PIN_STATE 0: Off
1: On
MODE_BLK
O2_PERCENT_OF_ 0.0-100.0
RANGE
O2_RANGE 0-40
OXY_BLOCK_ALARM See section 4.7
in FF-903
OXY_BLOCK_ERR See table 3
PRIMARY_VALUE 0.0-25.0
(O2_VALUE)
PRIMARY_VALUE_ See section 4.1
TYPE in FF-903
SECONDARY_VALUE -10000 - 10000
SECONDARY_VALUE_
UNITS
SENSOR_CAL_DATE
SENSOR_CAL_LOC
SENSOR_CAL_
METHOD
SENSOR_CAL_WHO
SENSOR_IMPEDANCE 0-10000
SENSOR_RANGE 0-100
SENSOR_SN
Initial
Value Units
mV This is the raw signal from the case/thermocouple
cold junction sensor.
See Transducer Block Specification, part 1. FF-902,
page 11.
0 N/A This indicates that a static parameter in the Oxymitter
has changed by some means other than Fieldbus.
0 Enumerated This is a bit-enumerated value used to communicate
the status of the Oxymitter. (This is similar in nature
to the command 48 status bits in HART.)
O
This is the highest temperature that has been
C
measured inside the electronics enclosure.
0 Enumerated This parameter is used to request the parameter
CASE_TEMP_MAX be reset to the current internal
case temperature. Setting this parameter at a value
of 1 will cause the transmitter to reset the
CASE_TEMP_MAX value. The transmitter will set
this parameter to 0 once it has completed this
process.
Enumerated This parameter represents the operating mode of the
discrete IO pin of the transmitter. 0 = Alarm Contact
Mode, 1=Calibration Sequence Mode.
Enumerated This parameter represents the current state of the
transmitters discrete IO pin. 0 = FALSE, 1 = TRUE.
See Function Block Specification, part 1. FF-890,
page 50.
% This is the percent of total range value.
%O2 This contains the upper and lower %O
the units, and the precision.
0 Enumerated This is the FF block alarm code. See Transducer
Blocks, part 2. FF-903, page 41.
0 Enumerated This is the Oxymitter's device alarm code. See Table
3.
%O2 This is the value that should appear on the output
channel of the transducer block. In the Oxymitter,
this is the present %O
any test gas being applied.
0 Enumerated Selected from list in Transducer Block Specification,
part 2. FF-903, page 39, section 4.1.
O
C See Transducer Block Specification, part 2. FF-903,
page 37. In the Oxymitter, this is the temperature of
the electronics.
See Transducer Block Specification, part 2. FF-903,
page 37.
See Transducer Block Specification, part 2. FF-903,
page 37.
See Transducer Block Specification, part 2. FF-903,
page 37.
Last calibration method. Selected from list in
Transducer Block Specification, part 2. FF-903,
page 40, section 4.5.
This is used to store the name of the individual who
last performed a calibration.
Ohms This is the sensor impedance value that was last
measured.
%O2 See Transducer Block Specification, part 2. FF-903,
page 37.
See Transducer Block Specification, part 2. FF-903,
page 37.
IB-106-350
A-2
Description
range values,
2
reading and should reflect
2
Parameter
Number
45
12
51
55
38
39
40
41
5
15
16
53
52
13
14
49
50
36
35
34
42
30
32
33