Setup; How To Operate The Setup Mode; Default Settings, Firmware Version; Input Settings - McIntosh D1100 Owner's Manual

How to Operate the Setup Mode

Your McIntosh D1100 has been factory configured for
default operating settings that will allow immediate
enjoyment of superb audio without the need for further
adjustments. If you wish to make changes to the fac-
tory default settings, a Setup Feature is provided to
customize the operating settings using the Front Panel
Information Display. Refer to the D1100 Front Panel
Illustration on the previous page while performing the
following steps.
Notes: 1. If the D1100 is connected to an Analog only Pre-
amplifier, via the Preamplifier Data Intercon-
nection Cable, AC Power to the Analog Pream-
plifier must be switched Off in order to use the
D1100 SETUP MODE Features.
2. If the D1100 is currently On, proceed to step 2.
1. Press the STANDBY/ON Push-button on the Front
Panel or press the (Power ON) Push-button on
the Remote Control to switch On the D1100. The
D1100 will go through a brief startup initialization
with the Front Panel Information Display indicat-
ing the last used source and volume setting. This is
followed by the volume setting indication starting
at zero and then increasing to the last used volume
setting. Refer to figure 1.
USB
------
Figure 1
2. Press and hold in the INPUT Control until the
Front Panel Information Display indicates "D1100
V_.__, S/N: AFG____" (or higher Firmware ver-
sion). Refer to figure 2.
D1100 V1.00
S/N: AFG____
Figure 2
3. Rotate the INPUT Control to select the next
Setup Mode Menu item, "SETUP: Inputs, (Hold
INPUT)". Refer to figure 3. Continue to rotate
the INPUT CONTROL to view the other SETUP
Mode Options.
SETUP: Inputs
4. To exit from the SETUP Mode, momentarily press
in the INPUT Control and the Front Panel Display
will revert back to its normal display. Refer to
figure 1.
Default Settings
The Default Settings Chart below indicates the Func-
tion Name, Default Setting and the Page Number for
additional information.
Function Name
D1100
INPUTS
OUTPUTS (1 & 2)
TRIGGER (1 thru 4)
15%
DATA PORTS
(1 thru 4)
RS232 (Rate)
IR Codes
(Remote Control)
Front IR (Sensor)
Auto-Off
(Power Mode)
Firmware Version
The D1100 functionality is controlled by internal
software that is know as Firmware. The Version of the
(Hold INPUT)
Figure 3
Default Settings
Setting Page No.
V_._ _ - _._ 13
On / Name 13
Switched 15
On 16
All Data 17
115200 Baud 17
17
Normal
Enabled 18
18
Enabled
Firmware in the D1100 can be identified at any time
by utilizing the Setup Mode.
1. Press and hold in the INPUT Control to enter
Setup Mode.
2. Referring to the Front Panel Information Display-
the number after the character "V" is the Firm-
ware number. Refer to figure 2.
3. To exit the Setup Mode, momentarily press the
INPUT Control.

Input Settings

The D1100 provides the ability to switch unused
INPUTS Off (or back On if they have been previously
switched Off). The default INPUT Names can be
changed to the name of the component connected to it
or any custom name desired (within 10 Characters).
INPUT SWITCHED ON/OFF:
In the following example, the COAX 3 Input will be
switched Off.
Note: When an INPUT is swiched Off, its name will
no longer appear on the Front Panel Informa-
tion Display when using the INPUT Control
(Front Panel or Remote Control).
1. Press and hold in the INPUT Control to enter the
SETUP MODE. Refer to figure 2.
2. Rotate the INPUT Control until "SETUP: Inputs,
(HOLD INPUT)" appears on the Information Dis-
play. Refer to figure 3.
3. Press and hold in the INPUT Control until
"SETUP: _______, On/Name (HOLD INPUT)"
appears on the Display. If necessary rotate the
VOLUME Control to select the COAX 3 Input.
Refer to figure 4.
SETUP: COAX 3
On/Name (Hold INPUT)
Figure 4

Setup

13