Table of Contents
Advertisement
How to Operate the Setup Mode
Your McIntosh C2700 has been factory configured for
default operating settings that will allow immediate
enjoyment of superb audio without the need for fur-
ther adjustments. If you wish to make changes to the
factory default settings, a Setup Feature is provided to
customize the operating settings using the Front Panel
Information Display. Refer to the C2700 Front Panel
Illustration on the previous page while performing the
following steps.
Note: If the C2700 is currently On, proceed to step 2.
1. Press the STANDBY/ON Push-button on the Front
Panel or press the
(Power ON) Push-button on
the Remote Control to switch On the C2700. Refer
to page 9 for information about Switching Power
On to the C2700. After the C2700 goes through
its startup, the Front Panel Information Display
indicates the last used source and volume setting.
This is followed by the volume setting indication
starting at zero and then increasing to the last used
volume setting. Refer to figure 1.
Figure 1
Front Panel Information Display indicates "C2700,
V1.00 - S/N: AHM____" (or higher Firmware
version). Refer to figure 2.
C2700
V1.00
S/N:
AHM____
Figure 2
3. Rotate the INPUT Control to select the next
Setup Mode Menu item, "SETUP: Inputs, (Hold
INPUT)". Refer to figure 3. Continue to rotate
the INPUT CONTROL to view the other SETUP
Mode Options.
SETUP: Inputs
4. To exit from the SETUP Mode, press and hold in
the INPUT Control and the Front Panel Display
will revert back to its normal display. Refer to
figure 1.
Default Settings
The Default Settings Chart below indicates the Func-
tion Name, Default Setting and the Page Number for
additional information.
Function Name
C2700
DA2
INPUTS
OUTPUTS (1 & 2 & Headphones)
POWER CONTOL TRIGGERS
(1 thru 4)
15%
HDMI CEC (Consumer Electronic Control)
HDMI CEC Power
Lip Synchronize Mode (Video and Audio)
Digital Gain (for HDMI, Optical 1 & Optical 2)
Comm Port Baud Rate
Remote Control Codes
IR Sensor
Power Mode
Factory Reset
Firmware Version
The C2700 functionality is controlled by internal
software that is know as Firmware. There are two
Firmware Identification Numbers for the C2700. The
first Firmware Number is for the Main Circuitry of the
C2700 and can be identified at any time by utilizing
(Hold INPUT)
Figure 3
Default Settings
Setting
Page No.
V1.00
13
V1.00
13
13-15
Switched
15
Various Settings
16
16
17
Control Command
17
Power On or Off
17
Activate or Deactivate
18
Input Comparison
18
18
19
19
Enabled
19
Default Settings
20
the Setup Mode.
1. Press and hold in the INPUT Control to enter
Setup Mode.
2. Referring to the Front Panel Information Display-
the number after the character "V" is the Firm-
ware number. Refer to figure 2.
To view the second Firmware Number, which is for
the Digital Audio Circuitry of the C2700, perform the
following steps:
3. Press and hold in the INPUT Control to enter
Setup Mode.
4. Rotate the INPUT Control until the Front Panel
Information Display indicates "DA2 Firmware,
V1.00" (or higher Digital Audio Firmware ver-
sion). Refer to figure 4.
DA2 FIRMWARE
V1.00
Figure 4
5. To exit the Setup Mode, press the INPUT Control.
Input Settings
The C2700 provides the ability to switch unused
INPUTS Off (or back On if they have been previously
switched Off). The default INPUT Names can be
changed to match the name of the component con-
nected to it or any other custom name desired (within
10 Characters).
INPUT SWITCHED ON/OFF:
In the following example, the UNBAL 4 Input will be
switched Off.
Note: When an INPUT is swiched Off, its name will
no longer appear on the Front Panel Informa-
tion Display when using the INPUT Control
(Front Panel or Remote Control).
1. Press and hold in the INPUT Control to enter the
SETUP MODE. Refer to figure 3.
Setup
13
Hide quick links:
Advertisement
Chapters
Table of Contents
