Option Settings - Philips Q548.1E Service Manual

• Set the RED, GREEN and BLUE default values according
to the values in Table
• When finished press OK on the RC, then press STORE (in
the SAM root menu) to store the aligned values to the NVM.
• Restore the initial picture settings after the alignments.
Table 6-2 White tone default settings Frame sets
(7000 series)
White Tone 32"
Colour Temp R G
Normal 127 93
Cool 127 98
Warm 127 83
Table 6-3 White tone default settings Roadrunner sets
(8000 series)
White Tone 32"
Colour Temp R G
Normal 127 93
Cool 127 100
Warm 127 83
Note: tint settings Frame sets (7000 series) 47" and 52", as
well as Roadrunner sets (8000 series) 37" and 47", were not
available at time of publishing.
6.3.3 LCD Panel Flicker Alignment
Note: This is only necessary for Forward Integration models
(sets that have the LCD Timing Controller (TCON) located on
the SSB) - not applicable to sets in this chassis.
See ComPair for further instructions.
6.4

Option Settings

6.4.1 Introduction
The microprocessor communicates with a large number of I
ICs in the set. To ensure good communication and to make
digital diagnosis possible, the microprocessor has to know
which ICs to address. The presence / absence of these
PNX5120 ICs (back-end advanced video picture improvement
IC which offers motion estimation and compensation features
(commercially called HDNM) plus integrated Ambilight control)
is made known by the option codes.
Notes:
• After changing the option(s), save them by pressing the OK
button on the RC before the cursor is moved to the left,
select STORE in the SAM root menu and press OK on the
RC.
• The new option setting is only active after the TV is
switched "off" / "stand-by" and "on" again with the mains
switch (the NVM is then read again).
6.4.2 Dealer Options
For dealer options, in SAM select "Dealer options".
See Table 6-5.
6.4.3 (Service) Options
Select the sub menu's to set the initialisation codes (options) of
the model number via text menus. See
6-1.
42" Black level
offset
B R G B R
100 127 116 112 8
122 125 114 124 8
61 127 108 73 8
42" Black level
offset
B R G B R
97 127 103 99 8
120 127 109 118 8
59 127 94 61 8
Table 6-5.
Alignments
6.4.4 Opt. No. (Option numbers)
Select this sub menu to set all options at once (expressed in
two long strings of numbers).
An option number (or "option byte") represents a number of
different options. When you change these numbers directly,
you can set all options very quickly. All options are controlled
via eight option numbers.
When the NVM is replaced, all options will require resetting. To
be certain that the factory settings are reproduced exactly, you
must set both option number lines. You can find the correct
option numbers on a sticker inside the TV set and in
G
Example: The options sticker gives the following option
8
numbers:
8
• 08192 00133 01387 45160
8
• 12232 04256 00164 00000
The first line (group 1) indicates hardware options 1 to 4, the
second line (group 2) indicate software options 5 to 8.
Every 5-digit number represents 16 bits (so the maximum value
will be 65536 if all options are set).
When all the correct options are set, the sum of the decimal
values of each Option Byte (OB) will give the option number.
G
SeeTable 6-4
8
8
Diversity
8
Not all sets with the same Commercial Type Number (CTN)
necessarily have the same option code!
Use of Alternative BOM An alternative BOM number usually
indicates the use of an alternative display or power supply. This
results in another display code thus in another Option code. For
the power supply there is no difference.
Refer to Chapter
6.4.5 Option Code Overview
Table 6-4 Option and display code overview
CTN
(Alt. BOM#)
32PFL7404H/12 08193 00649 01391 45288 10165 28832 00162 00000 181
42PFL7404H/12 08193 00651 01391 45288 10167 28832 00178 00000 183
47PFL7404H/12 08193 00651 01391 45288 10170 28832 00162 00000 186
52PFL7404H/12 08193 00651 01391 45288 10192 28832 00186 00000 208
32PFL8404H/12 08209 00656 02031 45288 26549 28834 00162 00000 181
2 37PFL8404H/12 08209 00656 02031 45288 26549 28834 00170 00000 161
C
42PFL8404H/12 08209 00657 02031 45288 26551 28834 00178 00000 183
47PFL8404H/12 08209 00657 02031 45288 26554 28834 00162 00000 186
Important: after having edited the option numbers as
described above, you must press OK on the remote control
before the cursor is moved to the left!
6.5 Reset of Repaired SSB
A very important issue towards a repaired SSB from a service
repair shop implies the reset of the NVM on the SSB.
A repaired SSB in service should get the service Set type
"00PF0000000000" and Production code "00000000000000".
Also the virgin bit is to be set. To set all this, you can use the
ComPair tool.
In case of a display replacement, reset the "Operation hours" to
"0", or to the operation hours of the replacement display.
Q548.1E LA 6.
for the options.
3. Precautions, Notes, and Abbreviation
Options Group 1 Options Group 2
EN 35
Table 6-4.
List.
Disp.
code
2009-Apr-03