Siemens 7SG11 Manual page 228

Setting name
Gn Status 1 P/U Delay
Gn Status 1 D/O Delay
Gn Status 2 P/U Delay
Gn Status 2 D/O Delay
Gn Status 3 P/U Delay
Gn Status 3 D/O Delay
Gn Status 4 P/U Delay
Gn Status 4 D/O Delay
Gn Status 5 P/U Delay
Gn Status 5 D/O Delay
Gn Status 6 P/U Delay
Gn Status 6 D/O Delay
Gn Status 7 P/U Delay
Gn Status 7 D/O Delay
Gn Status 8 P/U Delay
Gn Status 8 D/O Delay
Gn Status 9 P/U Delay
Gn Status 9 D/O Delay
Gn ARC Status A
Gn Trip Counter Reset
Gn Counter Reset
Gn FOC Reset
Gn Trip & ARC
Gn Close & Lockin
Gn Trip & Lockout
Gn Local Close & Reclaim
Gn Remote Close Reclaim
Gn CB Open
Gn CB Closed
Gn Reclose Block
Gn P/F ARC Off
Gn E/F ARC Off
Gn [SEF/REF] ARC Off
©2013 Siemens Protection Devices Limited
Ref Applied value
2.11 sec
2.11 sec
2.11 sec
2.11 sec
2.11 sec
2.11 sec
2.11 sec
2.11 sec
2.11 sec
2.11 sec
2.11 sec
2.11 sec
2.11 sec
2.11 sec
2.11 sec
2.11 sec
2.11 sec
2.11 sec
2.9.1
2.14.1
2.14.1
2.14.1
2.9.2
2.9.2
2.9.2
2.9.2
2.9.2
2.9.1
2.9.1
2.8.1
2.9.1
2.9.1
2.9.1
7SG11 Argus 6 Diagrams and Parameters
Setting name
Gn Hot Line Working
see note below
Gn Alarm 1 *
see note below
Gn Alarm 2 *
see note below
Gn Alarm 3 *
see note below
Gn Alarm 4 *
see note below
Gn Alarm 5 *
* The text of these setting names reflects the value
applied to the 'Set Alarm n' settings in the 'System
Config.' menu.
Comms Interface Menu
Setting name
Comms Baud Rate
Comms Parity
Relay Address
Line Idle
Data Echo
Data Storage Menu
Setting name
Gn Fault Trigger
Gn Waveform Trig
Gn Waveform Pre-Trigger
Clear All Waveforms
Clear All Events
Clear All Faults
CB Maintenance Menu
Setting name
Trip Counter Reset
Trip Counter Alarm
Trip Counter Reset
Trip Counter Alarm
Freq Op Counter Reset.
Freq Op Counter Alarm
I² Reset
I² Alarm
Power On Count Reset
Ref Applied value
2.9.4
2.2.5
2.2.5
2.2.5
2.2.5
2.2.5
Ref Applied value
4.3.1 baud
4.3.2
4.3.3
4.3.4
4.3.5
Ref Applied value
2.13.2
2.13.3
2.13.3 %
2.13.3
2.13.1
2.13.2
Ref Applied value
2.14.1
2.14.1
2.14.1
2.14.1
2.14.1
2.14.1
2.14.1
2.14.1
2.14.3
P20011 Page 10 of 22