Table of Contents
Advertisement
FOR YOUR SAFETY
READ BEFORE LIGHTING
WARNING: If you do not follow these instructions
exactly, a fire or explosion may result causing property
damage, personal injury or loss of life.
A. This appliance has a pilot that is equipped with an ignition
device which automatically lights the pilot. Do not light the
pilot by hand.
B. BEFORE LIGHTING smell all around the appliance area for gas.
Be sure to smell next to the floor because some gas is heavier
than air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electric switch; do not use any phone in your
building.
• Immediately call your gas supplier from a neighbor's phone.
Follow the gas supplier's instructions.
• If you cannot reach your gas supplier, call the fire department.
C. Use only your hand to push in or turn the gas control knob. Never
use tools. If the knob will not push in or turn by hand, don't try
to repair it, call a qualified service technician or gas supplier.
Force or attempted repair may result in a fire or explosion.
D. Do not use this appliance if any part has been under water.
Immediately call a qualified service technician to inspect the
appliance and to replace any part of the control system and any
gas control which has been under water.
INSTRUCTIONS
NOTICE: During initial operation of new fireplace, burn-
ing logs will give off a paper-burning smell. Orange
flame will also be present. Open damper or window
to vent smell. This will only last a few hours.
1. STOP! Read the safety information, column 1.
2. Turn wall switch (if installed) to the OFF position.
3. Turn off all electric power to appliance.
4. Place damper in full open position.
5. Fully open glass doors if installed.
6. Remove front refractory brick access panel.
7. Turn equipment shutoff valve clockwise
(see Figure 37).
8. Wait five (5) minutes to clear out any gas. Then smell for gas,
including near the floor. If you smell gas, STOP! Follow "B" in
the safety information, column 1. If you don't smell gas, go to
the next step.
9. Turn equipment shutoff valve counterclockwise
position. Do not force.
10. Replace front refractory brick access panel.
11. Fully close glass doors if installed.
12. Turn on all electric power to appliance.
13. Turn Wall switch to the ON position.
16
LIGHTING
to the OFF position
SuperiorFireplaces.US.com
OPERATION
14. Visually locate pilot. Ignitor should begin to spark and main burner
should ignite once flame appears at pilot.
•
If lighting appliance for the first time each season, it may
take several attempts before supply gas can reach pilot and
main burner.
•
If appliance will not stay lit after several attempts, follow
instructions in To Turn Off Gas To Appliance, and call your
service technician or gas supplier.
Equipment
Shutoff Valve
Figure 37 - Turning Equipment Shutoff Valve to the OFF Position
1. Turn off wall switch.
2. Turn off all electric power to appliance if service is to be performed.
3. Fully open glass doors if installed.
4. Remove front hearth brick and control access panel.
5. Turn equipment shutoff valve clockwise
force.
6. Replace front refractory brick access panel.
7. Fully close glass doors if installed.
Note: The WRC receiver and hand-held remote control kit must be
purchased separately (see Accessories, page 26). Follow installation
instructions on page 10.
1. Turn equipment shutoff valve to ON position. You can now turn
burner on and off with the hand-held remote control unit.
IMPORTANT: Be sure to press ON/OFF buttons on hand-held re-
mote control unit for up to 3 seconds to assure proper operation.
2. Press the ON/OFF button to turn burner on and off.
Pilot
Burner
to the ON
Adjustment
Screw
TO TURN OFF GAS
TO APPLIANCE
OPTIONAL REMOTE
OPERATION
Sensing
Rod
Ignitor
Figure 38 - Pilot
to OFF. Do not
126737-01_E
Advertisement
Table of Contents
