Life fitness parabody 844 lat option user's guide (17 pages)
Summary of Contents for ParaBody 813
Page 1
813 VKR/CHIN/DIP GYM SYSTEM USER’S GUIDE CLASS H PART # 7075701 REV. C WARNING: Read and follow all directions for each step to insure proper assembly of this product. Version: 813107 Revision: 08/06/01...
7. Inspect cables and their connections before using machine. Pay particular attention to the cable ends. DO NOT attempt to fix. Notify your authorized ParaBody dealer before use and have repairs made by an authorized service technician. 8. Make sure all spring loaded pull pins are fully engaged in the adjustment position and fully tighten thumbscrew before use.
Please note: * Thank you for purchasing the ParaBody 813 Gym System. Please read these instructions thoroughly and keep them for future reference. This product must be assembled on a flat, level surface to assure its proper function. * This product must be assembled on a flat, level surface to assure its proper function. DO NOT securely tighten any frame connections until the entire frame has been assembled, unless otherwise stated.
PART # DESCRIPTION 6102308 BASE CONNECTOR 6480008 CHIN BAR 6480508 VKR SIDE 6480908 UPPER BACK SUPPORT 6665921 BACK PAD 6752721 ARM PAD 3102501 3/8” FLAT WASHER 3102601 3/8” LOCK WASHER FIGURE 1 STEP 1: • Insert four 2” SQ. COVER CAPS (15) into the ends of the VKR SIDES (3) as shown in FIGURE 1. •...
Page 6
FIGURE 2 STEP 2: • LOOSELY assemble the UPPER BACK SUPPORT (4) to the VKR SIDES (3) using four 3/8 X 3” BOLTS (10), eight 3/8” FLAT WASHERS (7), and four 3/8” LOCK NUTS (9) as shown in FIGURE 2. •...
Page 7
10 3/8 X 3” FIGURE 3 STEP 3: • LOOSELY assemble the CHIN BAR (2) to the VKR SIDES (3) using two 3/8 X 3” BOLTS (10), four 3/8” FLAT WASHERS (7), and two 3/8” LOCK NUTS (9). • SECURELY tigten all connections made up to this point.
Page 8
3/8 X 3” 10 FIGURE 4 STEP 4: • SECURELY attach two ARM PADS (6) to the VKR SIDES (3) using four 3/8 X 3” BOLTS (10), four 3/8” LOCK WASHERS (8), and four 3/8” FLAT WASHERS (7) as shown in FIGURE 4. (NOTE: Place the high side of ARM PAD toward the outside.)
Page 9
3/8 X 3” FIGURE 5 STEP 5: • SECURELY assemble the BACK PAD (5) to the UPPER BACK SUPPORT (4) using two 3/8 X 3” BOLTS (10), two 3/8” LOCK WASHERS (8), two 3/8” FLAT WASHERS (7) as shown in FIGURE 5.
Page 10
FIGURE 6. (NOTE: Rubbing alcohol can be used on the inside of the grips to make them slide on easier.) Thank you for purchasing the Parabody 813102 VKR/CHIN/DIP GYM SYSTEM. If unsure of proper use of equipment, call your local Parabody distributor or call the Parabody customer service department at...
Please note: * We recommend cleaning your product (pads and frame) on a regular basis, using warm soapy water. Touch-up paint can be purchased from your ParaBody customer service representative at (800) 328-9714. * Inspect equipment daily. Tighten all loose connections are replace worn parts immediately.
ParaBody extends the following LIMITED WARRANTY to the original owner of the ParaBody products. The Warranty terms apply to IN HOME USE ONLY. 1. LIMITED WARRANTY ON FRAME AND WELDS. If the frame of the ParaBody product or a weld should crack or break, it will be repaired or replaced by ParaBody.
Page 13
Life Fitness Asia Pacific Limited Room 2610, Miramar Tower 132 Nathan Road, Tsimshatsui Kowloon, Hong Kong Phone: (852) 2891-6677 Fax: (852) 2575-6001 www.parabody.com Life Fitness (UK) Ltd. Queen Adelaide Ely, Cambs CB7 4UB United Kingdom Phone CSS: (01353) 665507 Fax CSS: (01353) 666719 Life Fitness Benelux N.V.