Related Manuals for ParaBody Parabody 844 Lat Option
Summary of Contents for ParaBody Parabody 844 Lat Option
- Page 1 844 LAT OPTION USER’S GUIDE CLASS H PART # 7079701 REV. B WARNING: Read and follow all directions for each step to insure proper assembly of this product. Version: 844107 Revision: 06/19/01...
- Page 2 Use only the pin provided by the manufacturer. If unsure, call your authorized ParaBody dealer. NOTE: In a continual effort to improve our products, specifications are subject to change 2001 Life Fitness, a division of Brunswick Corporation. All rights reserved. © ParaBody is a trademark of Brunswick Corporation www.parabody.com...
-
Page 3: Tools Required For Assembly
Please note: * Thank you for purchasing the ParaBody 844 Lat Option. Please read these instructions thoroughly and keep them for future reference. This product must be assembled on a flat, level surface to assure its proper function. * This product must be assembled on a flat, level surface to assure its proper function. DO NOT securely tighten any frame connections until the entire frame has been assembled, unless otherwise stated. -
Page 4: Parts List
PART # DESCRIPTION 6608708 UPRIGHT 6608508 TOP BOOM 6274402 LOW ROW BAR 6275302 LAT BAR 6609002 LOW ROW ATTACHMENT 6610402 KNEE SUPPORT 6546302 CARRIAGE 6609308 LOW PULLEY HOUSING 3116101 4-1/2” PULLEY 3116201 3-1/2” PULLEY 6610501 LAT CABLE 6576201 LOW ROW CABLE 6176201 ROLLER PAD 6542402... - Page 5 POWER RACK 1/2 X 3” 24 3/8 X 3-1/4” 19 FIGURE 2 STEP 2: • Assemble the LOW ROW ATTACHMENT (5) and the LOW PULLEY HOUSING (8) to the POWER RACK using two 3/8 X 3-1/4” BOLTS (19), four 3/8” WASHERS (20), and two 3/8” LOCK NUTS (21). See FIGURE 2. •...
- Page 6 FIGURE 3 STEP 3: • Apply eight 1” SQ. GLIDES (31) to the inside of the CARRIAGE (7) as shown in FIGURE 3. • Attach one 1-1/4” SQ. RUBBER BUMPER (30) to the bottom of the CARRIAGE (7) as shown in FIGURE 3. FIGURE 4 STEP 4: •...
-
Page 7: Cable Diagram
CABLE DIAGRAM... - Page 8 17 3/8 X 2-3/4 FIGURE 5 STEP 5: • Insert one 2 X 3” END CAP (27) into the TOP BOOM (2) as shown in FIGURE 5. • Route threaded end of the LAT CABLE (11) through the TOP BOOM (2) as shown in FIGURE 5. •...
- Page 9 FIGURE 6 STEP 6: • SECURELY assemble the TOP BOOM (2) to the UPRIGHT (1) using one 1/2 X 2-3/4” BOLT (23), one 1/2 X 3” BOLT (24), two 1/2” WASHERS (25), and one 1/2” LOCK NUT (26). See FIGURE 6. •...
- Page 10 FIGURE 7 STEP 7: • Loop the LAT CABLE (11) around one 3-1/2” PULLEY (10) as shown in FIGURE 7. • LOOSELY assemble the 3-1/2” PULLEY (11) to the1-3/4 X 5-1/4” PLATES (14) using one 3/8 X 2” BOLT (16) and one 3/8” LOCK NUT (21).
- Page 11 FIGURE 8 STEP 8: • Attach the LAT CABLE (11) to the CARRIAGE (7) using one 1/4” QUICK LINK (34) as shown in FIGURE 8. (IMPORTANT! Securely tighten QUICK LINK.) 3/8 X 2-3/4” 17 FIGURE 9 STEP 9: • Loop the ball end of the LOW ROW CABLE (12) around one 4-1/2” PULLEY (9) and SECURELY assemble the 4-1/2” PULLEY (9) to the LOW PULLEY HOUSING (8) using two 3/8 X 2-3/4”...
- Page 12 FIGURE 10 STEP 10: • Loop the LOW ROW CABLE (12) around one 3-1/2” PULLEY (10) as shown in FIGURE 10. • LOOSELY assemble the 3-1/2” PULLEY (10) to the 1-3/4 X 5-1/4” PLATES (14) using one 3/8 X 2” BOLT (16) and one 3/8” LOCK NUT (21).
- Page 13 STEP 12: • Attach the LAT BAR (4) to the ball end of the LAT CABLE (11) using one SNAP LINK (33) as shown in FIGURE 12.. • Slide two 1 X 8” GRIPS (15) over the ends of the LAT BAR (4) as shown in FIGURE STEP 13: •...
- Page 14 FIGURE 15 SAFETY RAIL STEP 15: • When performing the LAT PULL exercise, insert the KNEE SUPPORT (6) into the hole of the SAFETY RAIL as shown in FIGURE 15 and simply lower the SAFETY RAIL down until roller pads contact knees. THIS CONCLUDES THE ASSEMBLY OF THE 844 LAT OPTION...
- Page 15 YOU MAY NEED SERVICE YOU WILL BE ASKED FOR THIS INFORMATION. REMEMBER TO FILL OUT YOUR WARRANTY REGISTRATION CARD AND MAIL BACK. MODEL #________________________ SERIAL #_________________________ DATE OF PURCHASE: _____________ DEALERS NAME: _________________ DEALERS PHONE #_______________ Thank you for purchasing the ParaBody 844 Lat Option. MAINTENANCE...
-
Page 16: Limited Warranty
ParaBody extends the following LIMITED WARRANTY to the original owner of the ParaBody products. The Warranty terms apply to IN HOME USE ONLY. 1. LIMITED WARRANTY ON FRAME AND WELDS. If the frame of the ParaBody product or a weld should crack or break, it will be repaired or replaced by ParaBody. - Page 17 Life Fitness Italia S.R.L. Via Elvas 92 39042 Bressanone Italy Phone: 39 (472) 835-470 Fax: 39 (472) 833-150 Life Fitness Asia Pacific Limited Room 2610, Miramar Tower 132 Nathan Road, Tsimshatsui Kowloon, Hong Kong Phone: (852) 2891-6677 Fax: (852) 2575-6001 LIFE FITNESS www.parabody.com...