Table of Contents
Advertisement
Setup menus
<TIME CODE>
No./Item
4
For selecting whether or not to output the
500*
VITC signal at the positions selected by setup
menu items No.501 (VITC POS-1) and No.502
VITC BLANK
(VITC POS-2).
0000 BLANK:
0001
THRU:
<Note>
Only the SD output takes effect at this setting.
4
For setting the position where the VITC signal
501*
is to be inserted.
<59/60Hz>
VITC POS-1
0000
10L
:
0006
16L
:
0010
20L
<Notes>
• The same line as the one selected by the setup menu
item No.502 (VITC POS-2) cannot be selected.
• Only the SD output takes effect at this setting.
4
For setting the position where the VITC signal
502*
is to be inserted.
<59/60Hz>
VITC POS-2
0000
10L
:
0008
18L
:
0010
20L
<Notes>
• The same line as the one selected by the setup menu
item No.501 (VITC POS-1) cannot be selected.
• Only the SD output takes effect at this setting.
1
For setting the synchronization of the internal
503*
time code generator.
0000 REGEN:
TCG MODE
The time code reader is synchronized with the
time code which is read from the tape.
0001
PRE:
Presetting is enabled at the operation panel or
by the remote controller.
0002
AUTO:
The
REGEN
automatically switched in accordance with the
operation mode.
In the editing mode: REGEN is selected.
In all other modes: PRE is selected.
1
For setting when the internal time code
504*
generator is to advance depending on the
operation mode.
RUN MODE
0000
REC:
The time code generator is advanced during
recording.
0001
FREE:
The time code generator is advanced while the
power is on regardless of which operation
mode is established.
*1: This item is not displayed when the 23/24 Hz or 25 Hz (HD or SD) mode
has been selected as the system menu item No.25 (SYSTEM FREQ)
setting.
*2: This item is not displayed when the 23/24 Hz or 25 Hz (HD) mode has
been selected as the system menu item No.25 (SYSTEM FREQ) setting.
The underlining (__) denotes the factory setting mode.
Description of setting
The VITC signal is not output.
The VITC signal is output.
<50Hz, 25Hz (SD)>
0000
7L
:
:
:
0004
11L
:
:
:
0015
22L
<50Hz, 25Hz (SD)>
0000
7L
:
:
:
0006
13L
:
:
:
0015
22L
and
PRE
settings
No./Item
1
For selecting the regeneration signal when
505*
REGEN has been selected as the TCG (time
code generator) mode.
TCG REGEN
0000 TC&UB:
Regeneration applies to both the time code
and user's bit.
0001
Regeneration applies only to the time code only.
0002
Regeneration applies only to the user's bit only.
1
For selecting the editing mode range when
506*
the VTR is operating in the REGEN mode
while performing editing operations with
REGEN MODE
"AUTO" selected as the setup menu item
No.503 (TCG MODE) setting.
0000
Regeneration applies during assemble or
insert editing.
0001 ASSEM:
Regeneration applies during assemble editing.
0002
Regeneration applies during insert editing.
1
For selecting the time code to be used when
507*
HD SDI or SD SDI has been selected as the
setup menu item No.600 (VIDEO IN SEL)
TC SOURCE
setting when an external time code is to be
used.
[When HD SDI has been selected]
0000
The time code of the internal time code
generator is used.
0001
LTC of the TIME CODE IN connector is used.
0002
The LTC information added to the serial
signals which are input to HD SDI IN is used.
0003
The VITC information added to the serial
signals which are input to HD SDI IN is used.
[When SD SDI has been selected]
are
0000
The time code of the internal time code
generator is used.
0001
LTC of the TIME CODE IN connector is used.
0002
The VITC information added to the serial
signals which are input to SD SDI IN is used.
<Note>
If the VIDEO IN SEL input selection is changed, the time
code is converted as shown below.
[HD_SDI]
INT
EXT_L
SLTC
SVITC
Description of setting
TC:
UB:
AS&IN:
INSRT:
INT:
EXT_L:
SLTC:
SVITC:
INT:
EXT_L:
VITC:
[SD_SDI]
INT
EXT_L
EXT_L
VITC
91
Advertisement
Table of Contents
