O Edit - Panasonic HD1700pe Operating Instructions Manual

Setup menus
<EDIT>
No./Item
300 For selecting the operation to be performed when
an edit point has been set incorrectly (when the
IN/OUT DEL OUT point comes before the IN point).
0000 MANU:
Editing is not performed unless the illegal edit
point is cleared or set properly.
0001 AUTO:
The edit point which had already been input is
cleared automatically.
301 For selecting whether to show a negative display
(time code display area) when the IN point is
NEGA FLASH greater than the OUT point.
0000 OFF:
A negative display is not shown.
0001 ON:
A negative display is shown.
302 For selecting whether to perform simultaneous
playback during editing.
CONFI EDIT 0000 OFF:
0001 ON:
<Note>
Simultaneous playback takes effect when TAPE is
selected as the F1 key
<HOME> menu. Refer to setup menu item No.140 as
well.
1 For selecting how to connect the digital audio
303*
edit IN points.
0000 CUT:
AUD EDIT
0001 FADE:
IN
1 For selecting how to connect the digital audio
304*
edit OUT points.
0000 CUT:
AUD EDIT
0001 FADE:
OUT
305 For selecting whether to register the IN points
using the PREROLL button in cases where
AUTO ENTRY the IN points have not been registered.
0000 DIS:
0001 ENA:
1
For selecting the deck whose the color
306*
framing is to be adjusted during deck-to-deck
editing.
CF ADJ SEL
0000 PLAYER:
The player's IN and OUT points are adjusted
(using the recorder as the reference).
0001 RECORD:
The recorder's IN and OUT points are adjusted
(using the player as the reference).
307 For selecting
completion of the cue-up operation.
AFTER 0000 STOP:
CUE-UP The VTR is set to the STOP mode.
0001 STILL:
The VTR is set to the still picture (SHTL STILL)
mode.
0002 STILL2:
The VTR is set to the still picture (VAR STILL)
mode.
88
Description of setting
Simultaneous playback is not
performed.
Simultaneous playback
performed.
setting on the
OUTPUT
Cut processing
V-fade processing
Cut processing
V-fade processing
The IN points are
registered.
The IN points are registered.
the VTR's mode
No./Item
308 For setting the maximum speed of VAR FWD.
0000
VAR FWD 0001
MAX
0002
<Notes>
• At any setting other than 0 (i4.9), phase adjustments
cannot be conducted from the editing controller.
• Depending on the format used, the actual tape
running speed differs slightly from what is indicated
by the superimposed display.
309 For setting the maximum speed of VAR REV.
0000
0001
VAR REV MAX
0002
<Note>
Depending on the format used, the actual tape running
is
speed differs slightly from what is indicated by the
superimposed display
310 For setting the maximum speed of JOG FWD.
0000
0001
JOG FWD
MAX
0002
<Notes>
At any setting other than 0 (i4.9), phase adjustments
cannot be conducted from the editing controller which
performs these adjustments by the JOG command.
311 For setting the maximum speed of JOG REV.
0000
JOG REV MAX 0001
not
0002
312 For setting the postroll time.
Any time from 0 to 5 seconds can be set in 1-
POSTROLL second increments.
TM 0000
0001
0002
0003
0004
0005
upon
*1: This item is not displayed when the 23/24 Hz or 25 Hz (HD or
SD) mode has been selected as the system menu item No.25
(SYSTEM FREQ) setting.
The underlining (__) denotes the factory setting mode.
Description of setting
i4.9 times normal tape speed
i4.9:
i2 times normal tape speed
i2:
(i1.85 times normal
speed for formats other than
DVCPRO HD-LP)
i1 times normal tape speed
i1:
j4.9 times normal tape speed
j4.9:
2
: j2 times normal tape speed
j
(j1.85 times normal
speed for formats other than
DVCPRO HD-LP)
j1 times normal tape speed
j1:
.
i4.9 times normal tape speed
i4.9:
i2 times normal tape speed
i2:
(i1.85 times normal
speed for formats other than
DVCPRO HD-LP)
i1 times normal tape speed
i1:
j4.9 times normal tape speed
j4.9:
j2 times normal tape speed
j2:
(j1.85 times normal
speed for formats other than
DVCPRO HD-LP)
j1 times normal tape speed
j1:
0s
1s
2s
3s
4s
5s
tape
tape
tape
tape