Table of Contents
Advertisement
Error messages
Error messages
• Description
Display
• VTR operation and remedial action
FRONT LOAD
If the cassette fails to move up even after 6 seconds
have elapsed since the VTR transferred to the EJECT
MOTOR
mode, the AUTO OFF lamp lights, and the message
display blinks.
<Note>
If the cassette fails to move down even after 6 seconds
have elapsed since the cassette was inserted, the VTR
transfers to the EJECT mode.
VTR: Stops.
• Set the POWER switch to OFF and then back to ON
again.
LOADING
If the unloading operation fails to be completed within 6
seconds, the AUTO OFF lamp lights, and the message
MOTOR
display blinks.
<Note>
If the loading operation fails to be completed within 6
seconds, the VTR transfers to the EJECT mode
(unloading mode).
VTR: Stops.
• Set the POWER switch to OFF and then back to ON
again.
REEL DIR
If the take-up reel motor is running in the reverse
direction, the AUTO OFF lamp lights, and the message
UNMATCH
display blinks.
VTR: Stops.
• Set the POWER switch to OFF and then back to ON
again.
REEL
If an abnormal tension at the supply side is detected in
the reel mode, the AUTO OFF lamp lights, and the
TENSION
message display blinks.
ERROR
VTR: Stops.
• Set the POWER switch to OFF and then back to ON
again.
SERVO COMM
When the servo microcomputer does not follow the
instructions of the system control microcomputer even
ERROR
after 10 seconds have elapsed, the AUTO OFF lamp
lights, and the message display blinks.
VTR: Stops.
• Set the POWER switch to OFF and then back to ON
again.
SERVO
When there is no response from the servo
microcomputer for 1 or more seconds, the AUTO OFF
CONTROL
lamp lights, and the message display blinks.
ERROR
VTR: Stops.
• Set the POWER switch to OFF and then back to ON
again.
SERVO
When only the servo microcomputer was reset in an
instantaneous power failure, etc., the AUTO OFF lamp
ERROR
lights, and the message display blinks.
VTR: Stops.
• Set the POWER switch to OFF and then back to ON
again.
• Description
Display
• VTR operation and remedial action
S-FF/REW
When the tape start or end processing operation is not
completed, the AUTO OFF lamp lights, and the
TIMEOVER
message display blinks.
VTR: Stops.
• Set the POWER switch to OFF and then back to ON
again.
S REEL ROTA
If the supply reel motor rotates at an abnormally fast
rate, the AUTO OFF lamp lights, and the message
TOO FAST
display blinks.
VTR: Stops.
• Set the POWER switch to OFF and then back to ON
again.
S REEL
If an abnormal torque applied to the supply reel motor
is detected or if an abnormal current flowing to the
TORQUE ERR
current-sensing resistor is detected, the AUTO OFF
lamp lights, and the message display blinks.
VTR: Stops.
• Set the POWER switch to OFF and then back to ON
again.
T REEL ROTA
If the take-up reel motor rotates at an abnormally fast
rate, the AUTO OFF lamp lights, and the message
TOO FAST
display blinks.
VTR: Stops.
• Set the POWER switch to OFF and then back to ON
again.
T REEL
If an abnormal torque applied to the take-up reel motor
is detected, the AUTO OFF lamp lights, and the
TORQUE ERR
message display blinks.
VTR: Stops.
• Set the POWER switch to OFF and then back to ON
again.
If the tape has not been wound up during unloading,
UNLOAD
the AUTO OFF lamp lights, and the message display
ERROR
blinks.
VTR: Stops.
• Set the POWER switch to OFF and then back to ON
again.
WINDUP
If, after the total tape amount has been detected, the
amount of tape wound up onto the take-up reel and the
ERROR
amount of tape supplied by the supply reel differ to an
abnormal extent while the tape is traveling, the AUTO
OFF lamp lights, and the message display blinks.
VTR: Stops.
• Set the POWER switch to OFF and then back to ON
again.
W-UP REEL
If, after the cassette has been inserted, the tape take-
up reel has not wound up the tape while the total tape
NOT ROTA
amount is not detected and while the tape is traveling,
the AUTO OFF lamp lights, and the message display
blinks.
VTR: Stops.
• Set the POWER switch to OFF and then back to ON
again.
If the error message display persists even after the
VTR has been shut down and started up again,
consult your dealer.
121
Advertisement
Table of Contents
