Panasonic AJ-SD965 Operating Instructions Manual page 56

Setup menus
(continued)
USER menu
<AUDIO>
No./Item
721 This selects the monitor output.
MONI CH SEL 0000 MANU :
The output signal is as selected in MONITOR
SELECT buttons.
0001 AUTO :
PCM AUDIO output is selected within the
–0.43 (–0.5)a to +1a speed range; CUE is
automatically selected for all other tape
speeds.
<Note>
The value for the DV/DVCAM tape is shown in
parenthesis (
0002 PCM :
The PCM AUDIO signal is output over the
–10a to +10a range.
<Note>
This setup menu's setting takes effect when
CH1, CH2, CH3 or CH4 has been selected by
the L and R MONITOR SELECT buttons on the
front panel. (If CUE has been selected, the cue
signal will be output at all the speeds regardless
of the setup menu's setting.)
726 This selects the input signal recorded in
CUE.
REC CUE
0001
0002
0003 CH1+2 : Audio CH1 and CH2 MIX signal
0004
0005
0006 CH3+4 : Audio CH3 and CH4 MIX signal
CH1 ~ 4 : Audio CH1, CH2, CH3 and CH4
0007
727 This selects the processing method for the
audio edit points (IN point, OUT point) during
PB FADE playback.
0000 AUTO : According to the status during
0001 CUT : Forced CUT
0002 FADE : Forced FADE
728 This selects whether to superimpose the
audio data onto the SDI output.
EMBEDDED
AUD 0000
0001
The underlined items indicates the initial setting.
56
Description
).
CH1 : Audio CH1 input
CH2 : Audio CH2 input
CH3 : Audio CH3 input
CH4 : Audio CH4 input
mixed signals
recording.
OFF : Data is not superimposed.
ON : Data is superimposed.
No./Item
731 This selects whether or not the cue signal is
to be output to the main line output in the
CUE OUT SEL search mode.
0000 OFF : CUE is not output.
0001
<Notes>
OThis function works only when a setting
other than MANU has been selected by
setup menu No. 721 (MONI CH SEL).
OThe main signal system output channels
used for the CUE output differ depending
on the setting selected by setup menu No.
735 (MON AUTO SEL).
When L/R is selected:
CUE is output to CH1 to CH4.
When L is selected:
CUE is output to CH1 and CH3.
When R is selected:
CUE is output to CH2 and CH4.
OWhen PCM has been selected as the setup
menu No. 721 (MONI CH SEL) setting,
PCM is output.
733 This selects the timing for the output picture
and CUE output when CUE has been
CUE OUT selected for monitor output.
0000 NORMAL : The timing is aligned with the
0001 DIRECT : Whatever has been recorded on
<Note>
When DIRECT has been selected, the timing of
the output picture and that of the cue output are
not aligned properly.
734 This selects whether the operation of the
AUDIO MON SEL button on the front panel is
MONI SEL INH to be enabled or disabled.
0000 OFF : Operation is enabled.
0001
0002 ON1 :
Operation is disabled in the FULL display
mode and enabled only in the FINE display
mode.
735 Although CUE is automatically output to the
monitor output in accordance with the
MON AUTO operation mode when a setting AUTO has
SEL been selected by setup menu item No. 721
(MONI CH SEL), the MON AUTO SEL setup
menu item is used to select the monitor
channel which is to be automatically
switched to CUE.
0000 L/R :
CUE is output to both the left and right
channels.
0001
CUE is output to the left channel only.
0002
CUE is output to the right channel only.
Description
ON : CUE is output.
output picture.
the tape is output with no delay.
ON : Operation is disabled.
L :
R :