Source Connection - Integra DTR-20.7 User Manual

 The subwoofer sound may not be detected since it is extremely
¼
low frequencies. Set the subwoofer volume to around the half of its
maximum volume.
 Measurement may be interrupted if there is ambient noise or radio
¼
frequency interference. Close the window and turn off the home
appliance and fluorescent light.
2� After placing the microphone at the measurement
position, select "Do it Now" with the cursors and
press Enter�
3� When "Please plug microphone that came in a
box with AV receiver" is displayed, connect the
microphone to the Setup Mic jack of the unit�
Setup Mic jack
4� Select the settings for the connected speakers, the
type of the height speakers, and other appropriate
settings�
AccuEQ Room Calibration
Speaker Channels 7.1ch
Subwoofer Yes
Height Speaker -----
Bi-Amp No
Powered Zone2 No
Select how many speakers you have.
When the screen above is displayed, set the items with
the cursor buttons on the remote controller. Refer to
the on-screen diagram for "Speaker Channels", which
changes each time a different number of channels is
selected. When all the items have been set, press Enter
on the remote controller. After that, follow the guidance
displayed on the TV screen to operate the unit.
● Refer to the content of an item, which appears on
the lower left of the screen when the cursor is on the
item.
5� The test tones sound from the connected speakers
and automatic speaker setting starts�
Measurement will be made 3 times or more for each
speaker. It takes several minutes to be completed. Keep
the room as quiet as possible during measurement. If
any of the speakers do not produce the test tone, check
for disconnection.
● During measurement, each speaker outputs the test
tones at a high volume. Be careful of sound leak
that may disturb your neighbors, or be careful not to
frighten young children.
6� When the measurement is completed, the
measurement result is displayed�
Press /
t u
settings. Press Enter with "Save" selected. To have the
settings reflected for all the speakers, select "On (All
Channels)" in the next screen and press Enter on the
remote controller.
● Select "On (Except Front Left / Right)" to disable just
the front speakers.
Calibration
● If there is an error message, follow the on-screen
microphone
instruction to remove the error cause. If the
subwoofer was not detected, turn the volume of the
subwoofer up to maximum and then select "Retry".
7� When "Please unplug setup microphone�" is
displayed, disconnect the microphone�
2

Source Connection

You can check the connections on the different inputs and
make HDMI link function settings.
1� When the Source Connection start screen is
displayed, select "Yes, Continue" with the cursors
ENTER Next
and press Enter�
on the remote controller to check the
Initial Setup
Source Connection
This step will start to check if the
connections were made correctly.
Would you like to continue?
Yes. Continue
No. Skip
SETUP Exit
Step 2: Initial Setup
2� Select the desired input to check the connection and
press Enter�
Start playback of the selected device. If connection is
correct, video/audio of the input source selected on the
unit will be played.
3� After checking the connection, select "Yes" with the
cursors and press Enter�
● If you select "No" and press Enter, the error cause
will be displayed. Follow the guidance to remove the
error cause and check the connection again.
4� Select "Yes" with the cursors and press Enter on the
remote controller to check the connection of other
inputs or select "No, Done Checking" and press
Enter to skip�
If you select "Yes", you will return to the screen of step
2.
If you select "No, Done Checking", you will proceed to
step 5.
5� Set the CEC link function�
Select "Yes" to enable the HDMI link function with CEC-
compliant equipment, then select "Yes" again in the next
screen.
Source Connection
The following CEC-compatible devices are found;
Do you wish to turn on the CEC link?
xxxxxxxxxxx
Yes
No
If you select "Yes", the connection with ARC compatible
TV and HDMI Standby Through function will be set to
"On" and enabled.
SETUP Exit
En-13