Related Manuals for Digimerge DNZ9320W
Summary of Contents for Digimerge DNZ9320W
- Page 1 HARDWARE MANUAL English version 1.0 DNZ9320W DNZ9320W Networkable Camera © Copyright 2007 Digimerge Technologies Inc.
- Page 2 The Digimerge DNZ9320W offers the option of a wide dynamic range Speed Dome IP Network camera for finance, mercantile and institutional applications. The camera features 25x zoom, up to 360°/sec. travel, Lillin™ PTZ control protocol and selectable IR Cut filter.
- Page 3 Important Safeguards Important Safeguards In addition to the careful attention devoted to quality standards in the manufacture process of your video product, safety is a major factor in the design of every instrument. However, safety is your responsibility too. This sheet lists important information that will help to assure your enjoyment and proper use of the video product and accessory equipment.
- Page 4 18. Heat - The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat. © HARDWARE MANUAL | Copyright 2007 Digimerge Technologies Inc.
- Page 5 4. Keep enough space around the unit for ventilation. Slots and openings in the storage cabinet should not be blocked 5. During lightning storms, or when the unit is not used for a long time, disconnect the power supply, antenna, and cables to protect the unit from electrical surge DIGIMERGE TECHNOLOGIES INC. http://www.digimerge.com Revision 1.0...
- Page 6 DNZ9320W Camera Features SECTION 1 DNZ9320W Camera Features Technology • High Resolution (570 / 480 TV lines) • Sony 1/4” ExView HAD CCD Image Sensor • MPEG-4/MJPEG Dual Codec • Up to full D1 resolution at 30 fps • 25x Optical Zoom •...
-
Page 7: Table Of Contents
Package Contents ................. 10 Section 2 - PRODUCT OVERVIEW ..........11~14 DNZ9320W - Connection Overview ......... 12~13 DNZ9320W - Camera DIP Switches ..........14 Section 3 - INSTALLATION ............. 15~24 Installation Overview ..............16~20 1. Mounting the Camera ....................16 1A. - Page 8 Appendix #6 - Camera Address DIP Switch Settings ....46 Appendix #7 - Hardware Installation ..........47 Installation - Structural Drawings .................. 47 Installation - Embedded Mounting ................48~50 Installation - Attached Mounting ................51~52 Digimerge IP Products ..............53 Digimerge Warranty ..............54~55 © HARDWARE MANUAL | Copyright...
-
Page 9: Section 1 - Getting Started
SECTION 1 GETTING STARTED Package Contents......10... -
Page 10: Package Contents
1 x Package of Mounting Hardware (2 pieces) Ethernet Cable Software CD, Quick Installation Guide & Hardware Manual CHECK YOUR PACKAGE TO CONFIRM THAT YOU HAVE RECEIVED THE COMPLETE SYSTEM, INCLUDING ALL COMPONENTS SHOWN ABOVE. © HARDWARE MANUAL | Copyright 2007 Digimerge Technologies Inc. -
Page 11: Section 2 - Product Overview
SECTION 2 PRODUCT OVERVIEW DNZ9320W - Connection Overvie..12~13 DNZ9320W - Camera DIP Switches ...14... -
Page 12: Dnz9320W - Connection Overview
DNZ9320W - Connection Overview SECTION 2 DNZ9320W - Connection Overview The ports on the Camera are located in a removable IP Board along the bottom of the camera. Connections should be made before permanently attaching the Camera to the ceiling. - Page 13 DNZ9320W - Connection SECTION 2 DNZ9320W - Connection Overview The ports on the Camera are located in a removable IP Board along the bottom of the camera. Connections should be made before permanently attaching the Camera to the ceiling. 3. AUDIO IN - Connect an Audio device (i.e. Microphone) for Live Audio.
-
Page 14: Dnz9320W - Camera Dip Switches
DNZ9320W - Camera DIP Switches SECTION 2 DNZ9320W - Camera DIP Switches The DIP Switches on the Camera are located on the base (underside) of the camera. The camera should be removed from the IP Board by removing the 3 screws. -
Page 15: Section 3 - Installation
SECTION 3 INSTALLATION Installation Overview .....16~20 1. Mounting the Camera .....16 1A. Embedded Mounting ....17 1B. Surface Mounting ......18 2A. Power and Ethernet Connections 19 2B. Other Connections ......19 3. Software Installation Overview ..20 DigiViewer - PTZ Camera Setup ..21 A. -
Page 16: Installation Overview
• Install the Camera in a location where the ceiling board is more than 4cm (1.5”) thick. • Run all cables to the Camera Location before permanent mounting. Embedded Mounting Attached Mounting © HARDWARE MANUAL | Copyright 2007 Digimerge Technologies Inc. -
Page 17: Embedded Mounting
Installation Overview SECTION 3 1A. Embedded Mounting Before starting the Mounting procedure, confirm that the ceiling can hold the weight of the camera. A Safety Wire (not included) is also required. i. Cut a hole in the ceiling 170mm (6.7”) in diameter. ii. -
Page 18: Surface Mounting
(necessary) and any optional connection cables to the Camera before attaching the Base Cover. v. Use the Plastic Base Cover to shield the installation. Attach securely with three (3) screws (provided). © HARDWARE MANUAL | Copyright 2007 Digimerge Technologies Inc. -
Page 19: Power And Ethernet Connections
Installation Overview SECTION 3 2A. Power and Ethernet Connections Make sure that the cables have been run to the 2A-i Camera Location prior to permanent mounting. i. Connect the Ethernet Cable to the Ethernet Port on the base of the Camera. ii. -
Page 20: Software Installation Overview
SECTION 3 3. Software Installation Overview This IP device is provided with software applications to make the most of the Device. This includes software for installing, configuring and managing 1 or more Digimerge IP Devices. The following applications are included: •... -
Page 21: Digiviewer - Ptz Camera Setup
DigiViewer - PTZ Camera SECTION 3 DigiViewer - PTZ Camera Setup The DigiViewer application loads in the default web browser (internet Explorer, Firefox, Opera, Safari, etc.) and is sent from the IP device. This application is not installed to the local PC. The following steps must be performed to activate the PTZ controls on the DigiViewer. -
Page 22: Ptz Advanced Software Setup
• Serial Port: 2 • Serial Mode: RS485 • Serial Usage: 2 • Serial Baud: 9600 • Serial Data: 8 • Serial Parity: 0 • Serial Device: 1 (lilin) • Serial Stop: 1 © HARDWARE MANUAL | Copyright 2007 Digimerge Technologies Inc. -
Page 23: Ptz Controls
DigiViewer - PTZ Camera SECTION 3 C. PTZ Controls The controls shown below ONLY appear on a PTZ Type Camera once the camera settings have been configured (as shown in steps A and B). 1. PAN/TILT CONTROLS - Use the Up, Down, Left, Right and Diagonal arrows to control the Pan and Tilt of the Camera. -
Page 25: Section 4 - Network Connectivity
SECTION 4 NETWORK CONNECTIVITY Network Connectivity Overview ...26 Locating the MAC and IP Address ..27 Router Port Forwarding .......28 Setting Up Your DDNS Account ..29~30 DigiViewer DDNS Setup ......31 Remote Access with IE....32~33... -
Page 26: Network Connectivity Overview
DigiViewer to allow DDNS connectivity. Refer to page 25 for details. See the DigiConsole / DigiViewer Software Guide (provided with this Camera) for installation requirements and details on using the software. CAMERA INTERNET ROUTER (Not Included) (Not Included) © HARDWARE MANUAL | Copyright 2007 Digimerge Technologies Inc. -
Page 27: Locating The Mac And Ip Address
Select the Find Devices button. 2. The DigiConsole automatically locates all available Digimerge IP devices on the network, and displays a snapshot of the results. Click on any available device to display a snapshot image on the right side screen display. -
Page 28: Router Port Forwarding
To locate your external IP address, visit http://www.whatismyip.com NOTE: If using multiple IP Devices on the same network, each device will need to be assigned to a different remote access port. © HARDWARE MANUAL | Copyright 2007 Digimerge Technologies Inc. -
Page 29: Setting Up Your Ddns Account
Setting Up Your DDNS Account Digimerge offers a free DDNS server for use with your IP Camera. A DDNS account allows you to set up a web site address that points back to your Local Network. The following outlines how to set up your free DNS account. -
Page 30: Setting Up Your Ddns Account
Domain Name: _______________________________________________ User Name: _________________________________________________ Password: __________________________________________________ NOTE: The information sent to you in E-mail is CASE SENSITIVE. It is important when set- ting up your DDNS information on your device. © HARDWARE MANUAL | Copyright 2007 Digimerge Technologies Inc. -
Page 31: Digiviewer Ddns Setup
B. Click on the NETWORK SERVICES link. C. Enter the DDNS information received in the DDNS Confirmation Email: Check ‘Enable Digimerge Dynamic DNS Service Enter the DDNS Domain name you chose during the DDNS Registration process Enter the Account Name you setup during the DDNS Registration Process. -
Page 32: Remote Access With Internet Explorer
Remote Access with Internet Explorer Open Internet Explorer, and enter the Local IP (i.e. http://192.168.0.104 if inside the Local Network), the Remote IP (i.e. http://72.154.89.164) or DDNS Address (http:// myurl.digimerge.net) for the remote IP Device. http://myurl.digimerge.net Internet Explorer Security Warnings Several security warnings may appear (based on your Internet Explorer settings). -
Page 33: Internet Explorer Security Warnings - Program Installation
• Click the Install button to allow the ActiveX controls to be setup on the PC. Internet Explorer Security Warnings - Windows Firewall The Digimerge IP Devices require connectivity across the network, and may be flagged by the Windows Firewall when a connection to your PC is made. -
Page 35: Section 5 - Appendices
Appendix #2 - Alarm IN/OUT/RS-485 Appendix #3 - Changing the Camera Appendix #4 - Power Over Ethernet (PoE) Appendix #5 - Hardware Reset Appendix #6 - Camera Address DIP Switch Appendix #7 - Hardware Installation Other Digimerge IP Products Digimerge Limited Warranty... -
Page 36: Appendix #1 - Camera Specifications
Pictures (GOP) size (Advanced Features). Video Bit Rate 16K~4M bits/sec (CBR/VBR configurable) - (high quality VBR settings for MJPEG can reach up to 10MBps). Day / Night Function Removable IR Cut filter © HARDWARE MANUAL | Copyright 2007 Digimerge Technologies Inc. -
Page 37: Network
Appendix #1 - Camera Specifications SECTION 5 Network Network Interface: Network • 10/100 Base-T Ethernet Protocols: • TCP (UDP)/IP, IMCP, HTTP, FTP, SMTP, DHCP, NTP, DNS, DDNS, RTSP, RTP/TCP (UDP). PTZ Specifications Pan Travel 360° Continuous Tilt Travel -5° ~ +95° Pan / Tilt Accuracy ±... -
Page 38: Management
3.3 kg / 7.4lbs. packaging & accessories) Software Provided • DigiConsole Setup Utility • DigiViewer Web Browser Interface • 32 Channel NVR Viewing / Recording / Playback / Remote Access Application. © HARDWARE MANUAL | Copyright 2007 Digimerge Technologies Inc. -
Page 39: Appendix #2 - Alarm In/Out Block / Rs-485 Block
Appendix #2 - Alarm IN/OUT Block / RS-485 SECTION 5 Appendix #2 - Alarm IN/OUT Block / RS-485 Block The Alarm IN/OUT Terminal Block and RS-485 Terminal Block allow additional connections and controls to be performed with the camera Alarm IN/OUT Terminal Block Configuration The Alarm IN/OUT Terminal Block allows for up to 6 Alarm In and One Alarm out connection. -
Page 40: Keyboard Controller - Rs-485 Configuration
1. The 1st pin TXDI+ of RS-485 jack at back of the keyboard connects to TXDI+ of RS-485 jack on the Camera. 2. The 2nd pin TXDI-of RS-485 jack at back of the keyboard connects to TXDI-of RS-485 jack on the Camera. © HARDWARE MANUAL | Copyright 2007 Digimerge Technologies Inc. -
Page 41: Appendix #3 - Changing The Camera Network Settings
Appendix #3 - Changing the Camera Network SECTION 5 Appendix #3 - Changing the Camera Network Settings The network settings on the camera can be manually set using the DigiConsole application: Menu - Edit Network Parameters The Edit Network Parameters option allows the user to manually set the Network Device options (if desired). -
Page 42: Appendix #4 - Power Over Ethernet (Poe)
NOTE: Standard PoE allows devices to be powered with a power rating of up to 12.9W. DNZ9320W consumes more then 12.9W and therefore requires the use of High Power PoE (IEEE-802.3at) devices. - Page 43 Poe Injector + Splitter ⇒ ⇒ ⇒ Non-PoE Ethernet Switch PoE Injector Active Splitter IP Camera (non-PoE) Digimerge IP Devices are certified for use with Microsemi PoE hardware solutions. Visit www.microsemi.com/PowerDsine for details on all available PoE hardware solutions. Revision 1.0...
-
Page 44: Appendix #5 - Hardware Reset
1. Separate the Camera from the base: • Unplug the power from the camera. • Remove the 3 holding screws from the base. • Twist the camera to separate it from the base. © HARDWARE MANUAL | Copyright 2007 Digimerge Technologies Inc. - Page 45 Appendix #5 - Hardware Reset SECTION 5 2. Locate the reset button on the board. The reset button is located near the Audio port. 3. Use a plastic or wooden tool to press the Reset Button on the board. Using a metal tool may short out the board when the power is restored.
-
Page 46: Appendix #6 - Camera Address Dip Switch Settings
• If using a single camera, the address does not need to be changed. • If using multiple cameras, each camera must be set to a unique address using the internal DIP • switches. The DIP switches are shown below. © HARDWARE MANUAL | Copyright 2007 Digimerge Technologies Inc. -
Page 47: Appendix #7 - Hardware Installation
Appendix #7 - Hardware Installation SECTION 5 Appendix #7 - Hardware Installation Installation - Structural Drawings Embedded Mounting Surface Mounting Revision 1.0... -
Page 48: Installation - Embedded Mounting
Appendix #7 - Hardware Installation SECTION 5 Installation - Embedded Mounting © HARDWARE MANUAL | Copyright 2007 Digimerge Technologies Inc. - Page 49 Appendix #7 - Hardware Installation SECTION 5 Installation - Embedded Mounting Revision 1.0...
-
Page 50: Installation - Embedded Mounting
Appendix #7 - Hardware Installation SECTION 5 Installation - Embedded Mounting © HARDWARE MANUAL | Copyright 2007 Digimerge Technologies Inc. -
Page 51: Installation - Attached Mounting
Appendix #7 - Hardware Installation SECTION 5 Installation - Attached Mounting Revision 1.0... -
Page 52: Installation - Attached Mounting
Appendix #7 - Hardware Installation SECTION 5 Installation - Attached Mounting © HARDWARE MANUAL | Copyright 2007 Digimerge Technologies Inc. -
Page 53: Digimerge Ip Products
Digimerge IP Products SECTION 5 Digimerge IP Products Revision 1.0... -
Page 54: Digimerge Warranty
Digimerge, be repaired or replaced with equal or better product in terms of hard- ware features without charge if all the conditions set forth in this document are met. - Page 55 No claims or statements regarding the product, whether written or verbal, by salespeople, retailers, dealers or distribu- tors, that are not contained in this limited warranty or in the owner's manual are authorized by Digimerge and do not modify or expand this warranty. Some countries, states, or provinces do not allow the exclusion or limitation of implied warranties or the limitation of incidental or consequential damages for certain products supplied to consumers or the limitation of liability for personal injury.
- Page 56 It’s all on the web Product Information Specification Sheets User Manuals Software Upgrades Quick Start Guides Firmware Upgrades VISIT www.digimerge.com www.digimerge.com Digimerge Technologies Inc.