How To Fold And Move The Treadmill - Pro-Form 330 RT PETL40131 User Manual

HOW TO FOLD AND MOVE THE TREADMILL

HOW TO FOLD THE TREADMILL FOR STORAGE
Unplug the power cord. CAUTION: You must be able to
safely lift 20 kg (45 lbs.) to raise, lower, or move the
treadmill.
1. Hold the treadmill with your hands in the locations shown
at the right. CAUTION: To decrease the possibility of in-
jury, bend your legs and keep your back straight. As
you raise the treadmill, make sure to lift with your legs
rather than your back. Raise the treadmill about halfway
to the vertical position.
2. Move your right hand to the position shown and hold the
treadmill firmly. Using your left hand, pull the latch knob to
the left and hold it. Raise the treadmill until the frame
passes the latch pin. Slowly release the latch knob. Make
sure that the frame is securely held by the latch pin.
To protect the floor or carpet from damage, place a
mat under the treadmill. Keep the treadmill out of di-
rect sunlight. Do not leave the treadmill in the storage
position in temperatures above 30° C (85° F).
HOW TO MOVE THE TREADMILL
Before moving the treadmill, convert the treadmill to the stor-
age position as described above. Make sure that the latch
pin is fully inserted into the hole in the handrail and
locked into place as described above.
1. Hold the handrails and place one foot on the base as
shown.
2. Tilt the treadmill back until it rolls freely on the front wheels.
Carefully move the treadmill to the desired location. Never
move the treadmill without tipping it back. To reduce
the risk of injury, use extreme caution whilst moving
the treadmill. Do not attempt to move the treadmill
over an uneven surface.
3. Place one foot on the base, and carefully lower the tread-
mill until it is resting in the storage position.
Latch
Knob
Latch
Pin
Base
Front Wheels
14
2. Open part bag B. Press the Right Frame Spacer (13) and
the Left Frame Spacer (not shown) onto the sides of the
Frame (55) as shown. Make sure that the high side of
each Spacer is facing forward as shown. With the help
of a second person, carefully lift the Frame (55) and hold
the Spacers between the plates on the Uprights (89).
Align the hole in the plate on the Right Upright (89) with
the hole in the Right Frame Spacer (13). Loosely thread a
5" Bolt (10) and a 3/8" Star Washer (45) into the Spacer
and the Frame (55). Repeat this step on the left side of
the treadmill.
See drawing 2a. With the help of a second person, care-
fully tip the treadmill onto its left side as shown.
Feed the Wire Harness (22) into the large round hole near
the lower end of the Right Upright (89), and then pull the
Wire Harness out of the upper end as shown.
3. Open part bag C. With the help of a second person,
raise the Left and Right Uprights (88, 89) to the vertical
position.
Identify the Right Handrail (6), which has a large hole in
the left side. Feed the Wire Harness (22) into the rectan-
gular bracket on the Right Handrail out of the large hole.
(Note: It may be helpful to use needlenose pliers to pull
the Wire Harness out of the hole.) Press a Handrail Cap
(83) onto the lower end of the Right Handrail as shown.
Insert the rectangular bracket on the Right Handrail (6)
into the right Upright (89). Attach the Right Handrail and
the Handrail Cap (83) with three 1" Bolts (12) and two
1/4" Washers (108) as shown. Do not tighten the Bolts
yet.
Attach the Left Handrail (7) as described above. Note:
There is not a wire harness on the left side.
2
High
side
45
Plate
13
89 10
55
2a
89
22
22
3
7
22
Hole
12
12
108
88 6
108
83
12
12
12
7
12
108
89
83