Hardware Setup - Onkyo HT-RC160 Instruction Manual

Advanced Setup—Continued
.

Hardware Setup

This section explains items on the "Hardware Setup"
menu.
1 Press the [RECEIVER] button followed by
the [SETUP] button.
The main menu appears onscreen.
If the main menu doesn't appear, make sure the
appropriate external input is selected on your TV.
2 Use the Up and Down [q]/[w] buttons to
select "7. Hardware Setup", and then
press [ENTER].
The "Hardware Setup" menu appears.
1. Remote ID
2. Tuner
3. HDMI
3 Use the Up and Down [q]/[w] buttons to
select an item, and then press [ENTER].
The screen for that item appears.
4
Use the Up and Down [q]/[w] buttons to
select an item, and use the Left and Right
[e]/[r] buttons to change it.
The items are explained below.
5 When you've finished, press the
[SETUP] button.
The setup menu closes.
Note:
This procedure can also be performed on the AV receiver
by using its [SETUP] button, arrow buttons, and
[ENTER] button.
Remote ID
■ Remote ID
When several Onkyo components are used in the same
room, their remote ID codes may overlap. To differenti-
ate the AV receiver from the other components, you can
change its remote ID from 1, the default, to 2 or 3.
Note:
If you do change the AV receiver's remote ID, be sure to
change the remote controller to the same ID (see below),
otherwise, you won't be able to control it with the remote
controller.
Changing the Remote Controller's ID
1
While holding down the [RECEIVER] but-
ton, press and hold down the [SETUP]
button until the Remote indicator lights up
(about 3 seconds).
78
7. Hardware Setup
2
Use the number buttons to enter ID 1, 2, or
3.
The Remote indicator flashes twice.
Tuner
■ FM/AM Frequency Step
See "FM/AM Frequency Step Setup" on page 43.
HDMI
■ Audio TV Out
This preference determines whether audio received at
the HDMI IN is output by the HDMI OUT. You may
want to turn this preference on if your TV is connected
to the HDMI OUT and you want to listen to the audio
from a component that's connected to an HDMI IN,
through your TV's speakers. Normally, this should be set
to "Off".
Off: HDMI audio is not output (default).
On: HDMI audio is output.
Notes:
• If " On " is selected and the signal can be output by the
TV, the AV receiver will output no sound through its
speakers.
• If "On" is selected, "TV Sp On" appears on the Dis-
play by pressing the [DISPLAY] button.
• When TV Control is set to
" "
to " Auto " .
• With some TVs and input signals, no sound may be
output even when this setting is set to
• When the "Audio TV Out" setting is set to
TV Control" is set to
" "
through your TV's speakers (see page 23), if you turn
up the AV receiver's volume control, the sound will be
output by the AV receiver's front left and right speak-
ers. To stop the AV receiver's speakers producing
sound, change the settings, change your TV's settings,
or turn down the AV receiver's volume.
■ Lip Sync
The AV receiver can be set to automatically correct any
delay between the video and the audio, based on the data
from the connected monitor.
Disable: HDMI lip sync disabled (default).
Enable: HDMI lip sync enabled.
Notes:
• This function works only if your HDMI-compatible
TV supports HDMI Lip Sync.
• You can check the amount of delay being applied by
the HDMI Lip Sync function on the A/V Sync screen
(see page 75).
On , this setting is fixed
" "
On .
" "
On , or
" "
On and you're listening
"