Onkyo TX-SR707 Instruction Manual page 125

Troubleshooting—Continued
Others
The sound changes when I connect my
headphones
• When a pair of headphones is connected, the listening
mode is set to Stereo, unless it's already set to Stereo,
Mono, Direct, Pure Audio or DTS Surround Sensa-
tion.
The display doesn't work
• The display is turned off when the Pure Audio listen-
ing mode is selected.
How do I change the language of a multiplex
source
• Use the "Multiplex" setting on the "Audio Adjust"
menu to select "Main" or "Sub" (page 84).
The u functions don't work
• To use u, you must make an u connection and an
analog audio connection (RCA) between the compo-
nent and AV receiver, even if they are connected digi-
tally (page 39).
The functions Auto Power On/Standby and
Direct Change don't work for components
connected via u
• These functions don't work when Zone 2 is turned on.
When performing "Audyssey MultEQ
Correction and Speaker Setup", the
measurement fails showing the message
"Ambient noise is too high.".
• This can be caused by any malfunction in your speaker
unit. Check if the unit produces normal sounds.
The following settings can be made for the S-
Video, composite video and COMPONENT
VIDEO inputs
You must use the buttons on the AV receiver to make
these settings.
1. While holding down the input selector button for the
input source that you want to set, press the [SETUP]
button.
2. Use the Left and Right [e]/[r] buttons to change
the setting.
3. Press the input selector button for the input source
that you want to set when you've finished.
• Video Attenuation
This setting can be made for the DVD/BD, VCR/
DVR, CBL/SAT, GAME, AUX, or COMPONENT
VIDEO input. (You need to assign the input source
for COMPONENT VIDEO input.)
If you have a games console connected to the
S-Video, composite and component video input, and
the picture isn't very clear, you can attenuate the
gain.
Video ATT:OFF: (default).
Video ATT:ON: Gain is reduced by 2 dB.
The AV receiver contains a microcomputer for signal pro-
cessing and control functions. In very rare situations,
severe interference, noise from an external source, or
static electricity may cause it to lockup. In the unlikely
event that this happens, unplug the power cord from the
wall outlet, wait at least five seconds, and then plug it
back in again.
Onkyo is not responsible for damages (such as CD
rental fees) due to unsuccessful recordings caused by
the unit's malfunction. Before you record important
data, make sure that the material will be recorded cor-
rectly.
Before disconnecting the power cord from the wall out-
let, set the AV receiver to Standby.
Important Note Regarding Video Playback
The AV receiver can upconvert component video, S-
Video, and composite video sources for display on a TV
connected to the HDMI OUT. However, if the picture
quality of the source is poor, upconversion may make the
picture worse or disappear altogether.
In this case, try the following:
®
Room
1 If the video source is connected to a component
video input, connect your TV to the
COMPONENT VIDEO MONITOR OUT.
If the video source is connected to an S-Video input,
connect your TV to a MONITOR OUT S.
If the video source is connected to a composite video
input, connect your TV to the MONITOR OUT V
2 On the main menu, select "1. Input/Output
Assign", and then select "2. HDMI Input".
Select the relevant input selector, and assign it to
"- - - - -" (page 44).
3 On the main menu, select "1. Input/Output
Assign", and then select "3. Component Video
Input" (page 45):
If the video source is connected to COMPONENT
VIDEO IN1, select the relevant input selector, and
assign it to "IN1".
If the video source is connected to COMPONENT
VIDEO IN2, select the relevant input selector, and
assign it to "IN2".
If the video source is connected to an S-Video input
or composite video input, select the relevant input
selector, and assign it to "- - - - -".
125