Remote Controller; Video Control - Kenwood DDX6034 Service Manual

DDX6034/6034M/6054/7034BT/7034BTM/714
DNX7000EX/7140/7240BT/7340BT
2.4.2. Key
Even in the Test mode, the specifi cations of the hard key
shall be the same as while in normal operation.
For your reference, the multiple pressing specifi cations of
the key are described in Table 2.4.2. (The original text of
the multiple pressing key specifi cations is the "09_hard key
specifi cations .xls" of Notes DB.)
Multiple Pressing Key
SRC + ATT + Reset
NAV (Menu) + Eject + Reset
SRC + AUD + Reset
Eject + AUD + Reset
SRC + Reset
Eject + Volume Down + Reset
SRC + Volume Down + Reset
Table 2.4.2 (for reference)
Multiple pressing key specifi cations

2.4.3. Remote controller

The remote controller key specifi cation is listed in Table 2.4.3.
(Note that the keys that are not listed in the table have con-
ventional functions.)
Select Audio SW mode on the remote controller.
Key
FM DVD video inspection mode
AM DVD audio inspection mode
Tenkey #0 Transfer to the Flicker Adjustment screen
Tenkey #2 Set the Volume value as Step26
Tenkey #3 Change the V-IN (R-CAM) mirror mode switching
Tenkey #5 Forcible Navigation Voice Interruption ON/OFF
Tenkey #6 Transfer to the Screen Adjustment screen
Tenkey #9 Use for design examinations
Table 2.4.3 Remote Controller key

2.4.4. Video control

Switch AV-OUT linking with the Source (In the case that the
Source is other than those indicated in the following sec-
tion, do not specify AV-OUT in particular).
Source: AV-IN → AV-OUT: AV-IN
Source: iPod → AV-OUT: iPod
Source: DVD → AV-OUT: DVD
Source: USB → AV-OUT: USB
Source: SD → AV-OUT: SD
Source: TV → AV-OUT: TV
Source: NAVI → AV-OUT: NAVI (Only DNX)
22
TEST MODE
Operation
Test Mode ON
Span switching
DC Offset/Service/Memory
Other Clear
Retailer mode: ON
Retailer mode: OFF
RDS test drive mode ON
Opening screen customization
Function
2.4.5. Tuner
• When unable to access E2PROM, display Error (on the
Tuner screen).
• K3I forced switching
Forced to Narrow by pressing and hold Preset 4
: xxx.x1MHz
Forced to Middle by pressing and holding Preset 5
: xxx.x2MHz
Forced to Wide by pressing and holding Preset 6
: xxx.x3MHz
• Perform the Span switching (K↔M) with the [NAV (Menu)]
key, the [Eject] key, and the [Reset] key.
The Span information is displayed on the Information
screen.
• When RDS PS is "RDS_TEST" in the Tuner source, turn
OFF P-CON.
2.4.6. DVD
• CDDA Check (KTD-02A)
Play back Track 1 while performing the Loading opera-
tion.
Use "Track UP/DW" to play back in the order of se-
quence as shown below
: 1↔9↔15↔10↔11↔12↔13↔14↔9↔1 · · ·
Perform Direct selection of channel to Track 28 by press-
ing the [RDM] key.
• DVD audio/video checking (TDV-540A/TTD-100)
Play back Title 1-Chapter 1 while performing the Loading
operation.
Use "Chapter UP/DW" to play back in the order of se-
quence as shown in Tables 2.4.6-1 and 2.4.6-2.
Use FM/AM on the remote controller to change the vid-
eo/audio check. (Default: Video Check)
For DVD video checking.
Title Chapter
3 6 Level
3 17 AM/PM noise
Frequency charac-
3 8
teristics
3 12 Color measurement
4 1 1kHz, 0dB
4 6 17Hz
Table 2.4.6-1 DVD Video check
Audiostream
Audiostream1
Audiostream1
Audiostream1
Audiostream1
PCM96k/24bit Audiostream3
PCM96k/24bit Audiostream3