Table of Contents
Advertisement
QQ
3 7 63 1515 0
TV control buttons
To
Set the TV to standby mode
Select an input source: aerial in or line in
Select the TV's programme position
TE
L 13942296513
12
Setting up the remote commander
Code numbers of controllable TVs
If more than one code number is listed, try entering them one at a time until
you find the one that works with your TV.
To switch to wide mode, see the footnotes below this table for the applicable
code numbers.
Manufacturer
Sony
Akai
Ferguson
Grundig
Hitachi
JVC
Loewe
Mivar
NEC
Nokia
1
*
Press WIDE to switch the wide picture mode on or off.
Press WIDE, then press 2 +/– to select the wide picture mode you want.
*
2
Press WIDE. The menu appears on the TV screen. Then, press M/m/</, to
*
3
select the wide picture you want and press OK.
Tip
• When you set your TV's code number correctly while the TV is turned on, the TV
turns off automatically.
Notes
• If you enter a new code number, the code number previously entered will be
erased.
• If the TV uses a different remote control system from the one programmed to work
with the VCR, you cannot control your TV with the remote commander.
• When you replace the batteries of the remote commander, the code number may
change. Set the appropriate code number every time you replace the batteries.
www
.
14
Setting up the remote commander
http://www.xiaoyu163.com
WIDE
AUDIO MONITOR
FASTEXT buttons
DISPLAY
1
2
3
4
5
6
7
8
9
-
0
Press
?/1
t TV/VIDEO
Programme number buttons,
-, PROG +/–
Code number
Manufacturer
1
Panasonic
01*
, 02
68
Philips
52
Saba
10*
1
, 11*
1
Samsung
24
Sanyo
33
Sharp
45
Telefunken
09, 70
Thomson
66
Toshiba
15, 16, 69*
3
x
ao
y
i
http://www.xiaoyu163.com
8
To
Adjust the volume of the TV
Switch to TV (Teletext off)*
Switch to Teletext*
Select the sound
? ? ? ? /1 1 1 1
/
Use FASTEXT*
a
Call up the on-screen display
Change the Teletext page*
Switch to/from wide mode of a Sony wide TV (For
t TV/VIDEO
t
t
t
other manufactures' wide TVs, see "Controlling
other TVs with the remote commander (SLV-
SE810N/K only)" below.)
Programme
Notes
number
• With normal use, the batteries should last about three to six months.
buttons
• If you do not use the remote commander for an extended period of time, remove
the batteries to avoid possible damage from battery leakage.
• Do not use a new battery together with an old one.
• Do not use different types of batteries together.
PROG +/–/
c/C
• Some buttons may not work with certain Sony TVs.
2
2 +/–
2
2
* SLV-SE810N/K only
Controlling other TVs with the remote commander
(SLV-SE810N/K only)
The remote commander is preprogrammed to control non-Sony TVs. If your
TV is listed in the following table, set the appropriate manufacturer's code
number.
Set [TV] / [VIDEO] at the top of the remote commander to [TV].
1
Hold down ?/1, and enter your TV's code number using the programme
2
number buttons. Then release ?/1.
Now you can use the following TV control buttons to control your TV:
?/1, t TV/VIDEO, programme number buttons, - (ten's digit),
PROG +/–, 2 +/–, a (TV), / (Teletext), FASTEXT buttons, WIDE*,
MENU*,
* These buttons may not work with all TVs.
Q Q
3
6 7
1 3
Step 3 : Connecting the VCR
If your TV has a Scart (EURO-AV) connector, see page 16.
Code number
If your TV does not have a Scart (EURO-AV) connector
1
17*
, 49
1
1
1
06*
, 07*
, 08*
12, 13
22, 23
25
Mains lead
29
36
to mains
43*
2
38
: Signal flow
1
2
3
Note
u163
• When you connect the VCR and your TV only with an aerial cable, you have to
tune your TV to the VCR (see page 19).
.
1-3
2 9
9 4
2 8
Press
2 +/–
a (TV)
/ (Teletext)
AUDIO MONITOR
FASTEXT buttons
DISPLAY
c/C
WIDE
M
m
<
,
/
/
/
*, and OK*.
1 5
0 5
8
2 9
9 4
Setting up the remote commander
AERIAL IN
AERIAL OUT
AERIAL IN
Aerial cable (supplied)
Disconnect the aerial cable from
AERIAL
ANTENNE
your TV and connect it to
IN
ENTREE
AERIAL IN on the rear panel of
the VCR.
OUT
SORTIE
Connect AERIAL OUT of the
AERIAL
ANTENNE
VCR and the aerial input of your
IN
ENTREE
TV using the supplied aerial cable.
OUT
SORTIE
Connect the mains lead to the mains.
m
co
9 9
2 8
9 9
continued
13
continued
15
Connecting the VCR
Hide quick links:
Advertisement
Table of Contents
