Table of Contents
Advertisement
Available languages
Available languages
high! Run the machine in idling until the electronics
signal indicator switches off.
The electronic signal display (9) flashes and
the machine stops. The electronics have switched
off the machine. Causes and remedies:
- Battery pack almost flat (the electronics prevent
the battery pack from discharging totally and avoid
irreparable damage). If necessary, press the (20)
button and check the LEDs (21) to see the charge
level. If the battery pack is almost flat, it must be
recharged.
- The temperature is too high! Run the machine in
idling until the electronics signal indicator
switches off.
- The machine was overloaded. Then continue
working as normal. Avoid further overloading.
The electronic signal display (9) flashes and
the machine does not start. The restart protection
is active. The machine will not start if the battery
pack is inserted while the machine is on. Switch the
machine off and on again.
The motor part cannot be moved up or down.
Pull out the lock switch (6).
10. Accessories
Use only genuine Metabo accessories.
If you need any accessories, check with your
dealer.
For dealers to select the correct accessory, they
need to know the exact model designation of your
power tool.
See page 4.
A Core drill bit with 19 mm Weldon shank, HSS /
HM / HSS-rapid cut (thin walls - for more
boreholes with a single battery charge)
B Centring pin, short,
HSS: for 30 mm cutting depth
C Centring pin, long,
HSS: for 55 mm cutting depth
HM: for core drill bit diameter 14-69 mm
D Morse taper for chuck with female taper
E Key-type chuck with female taper
F Metal drill bit
G Quick replacement system MK2 on Weldon,
19 mm
H Industrial holder MK2 on Weldon, 19 mm
I Securing belt with ratchet
J Universal cutting spray
K Battery charger
L Battery pack
For a complete range of accessories, see
www.metabo.com or the main catalogue.
11. Repairs
Have your power tool repaired by a qualified
electrician. This power tool complies with the
applicable safety regulations. Repairs must only be
carried out by qualified electricians and using
original spare parts; otherwise the user faces a risk
of accidents.
If you have Metabo electrical tools that require
repairs, please contact your Metabo service centre.
For addresses see www.metabo.com.
You can download spare parts lists from
www.metabo.com.
12. Environmental Protection
Metabo's packaging can be 100% recycled.
Scrap power tools and accessories contain large
amounts of valuable resources and plastics that can
be recycled.
Battery packs must not be disposed of with regular
waste. Return faulty or used battery packs to your
Metabo dealer!
Do not allow battery packs to come into contact with
water!
Only for EU countries: Never dispose of
power tools in your household waste! In
accordance with European Guideline 2002/
96/EC on used electronic and electric equipment
and its implementation in national legal systems,
used power tools must be collected separately and
handed in for environmentally compatible recycling.
Before disposal, discharge the battery pack in the
power tool. Prevent the contacts from short-
circuiting (e. g. by protecting them with adhesive
tape).
These instructions are printed on chlorine-free
bleached paper.
13. Technical Specifications
Explanatory notes on the specifications on page 3.
Changes due to technological progress reserved.
U
= Voltage of battery pack
T
= Tool attachment
M
= Max. torque
D
= Max. diameter (core drill bit)
max, C
D
= Max. diameter (spiral drill bit)
max, S
n
= No-load speed
0
H
= Max. stroke
max
H
= Height (incl. motor) with slide plate in
u
bottom position
H
= Height (incl. motor) with slide plate in top
o
position
A
= Dimensions of magnet block
m
= Weight with smallest battery pack
A-effective perceived sound levels:
L
=Sound pressure level
pA
L
=Acoustic power level
WA
K
, K
= Uncertainty (noise level)
pA
WA
During operation the noise level can exceed
80 dB(A).
Wear ear protectors!
Measured values determined in conformity with EN
61029.
The technical specifications quoted are subject to
tolerances (in compliance with the relevant valid
standards).
ENGLISH en
15
Advertisement
Table of Contents
