Initial Operation - Metabo MAG 28 LTX 32 Original Instructions Manual

en ENGLISH
5. Overview
See page 2.
1 Magnet block/Magnet
2 Handle
3 Supply cock on cooling lubrication unit
4 Container for cooling lubrication unit
5 Threaded pins for adjusting backlash of the
side plate
6 Lock switch to prevent the machine from
moving up/down accidentally
7 Slide plate
8 Switch (switching on/off driving unit)
9 Electronic signal indicator
10 Thumbwheel (1st /2nd gear)
11 Slot in machine neck for driving out tools
12 Removal tool (MK 2) *
13 Drill spindle with tool attachment (MK 2)
14 Anti-twist device
15 Tool holder threaded pins*
16 Tool holder (Weldon, 19 mm) *
17 Quick-action coupling of the cooling lubrication
unit
18 Battery pack
19 Two buttons for battery-pack release
20 Button for capacity and signal indicator
21 Capacity and signal indicator
22 Lever for moving driving unit up and down
23 Shaft
24 Display of magnet holding power
25 Ratchet switch lever (activate/deactivate
magnet)
26 Ratchet lever (activate/deactivate magnet)
27 Ratchet on securing strap
28 Securing strap
29 Two holding points
* depending on equipment/not in scope of delivery

6. Initial Operation

Check the machine for possible damage:
Before using the machine, you must carefully
check protective devices or slightly damaged
components to ensure they are operating perfectly
and as intended. Check that moving parts are in
perfect working order and do not jam and check
whether parts are damaged. All parts must be
correctly installed and fulfil all conditions necessary
to ensure perfect operation of the grinder. Damaged
protective devices and parts must be repaired or
replaced according to specifications by an
authorised specialist workshop.
6.1 Battery pack
Charge the battery pack before use (18).
If performance diminishes, recharge the battery
pack.
The ideal storage temperature is between 10°C and
30°C.
12
Li-ion battery packs Li-Power (25.2 V) have a
capacity and signal display (21):
- Press button (20) and the charge level is displayed
by the LEDs .
- If one LED is flashing, the battery pack is almost flat
and must be recharged.
- If all LED are flashing, the battery pack is too warm.
Allow the battery pack to cool down. You can do this
quickly using ASS 15 Plus battery charger.
6.2 Removing and inserting the battery pack
Removal:
Press both battery pack release buttons (19) and take
out battery pack (18).
Inserting:
Slide in the battery pack (18) until it engages.
7. Use
7.1 Attaching the Securing Strap
For drilling carried out on angled and vertical
surfaces and overhead, the magnetic drill
stand must be secured with the securing strap
(28)supplied to prevent it from falling, even if the
magnet malfunctions.
Fit the securing strap (28) so that the magnetic
drill stand is moved away from the operator if
the magnet malfunctions.
Replace the securing strap (28) if it has had to
catch a falling magnetic drill stand.
Caution! Check the securing strap (28) for
damage. Before using the securing strap (28),
always check it carefully to ensure it is operating
faultlessly and as specified. If the securing strap (28)
is damaged or if the ratchet (27) is no longer
working properly, replace the securing strap
immediately.
- Fit the securing strap (28) on one of the two holding
points (29) of the magnetic drill stand.
- Then secure the securing strap to another suitable
fastening point or to the material being processed.
(a)
- Notes on the securing strap (28):
Insert the free end of the securing strap from below
through the opening in the ratchet shaft and then
tension the free end of the securing strap until it is
loosely fitted.
The strap must not be tightly fitted: you must be
able to unroll the securing strap by more than
one rotation about the ratchet shaft - This is
essential to ensure secure fastening. Tension the
securing strap with a pumping action on the ratchet
lever (a).
(b)