Initial Operation; Installing The Tools - Metabo PE 15-20 RT Original Operating Instructions

See page 3 and chapter 14. Technical
Specifications for more information on the spindle
length and thread.
Use of a fixed extractor system is recommended.
Always install an RCD with a maximum trip current
of 30 mA upstream. When the machine is shut down
via the GFCI, it must be checked and cleaned. See
chapter 9. Cleaning.
When working in dusty conditions, ensure that
ventilation openings are not blocked. If it becomes
necessary to remove dust, first disconnect the
power tool from the mains supply (use non-metallic
objects) and avoid damaging internal components.
Damaged, eccentric or vibrating tools must not be
used.
Pull the plug out of the socket before making any
adjustments, converting or servicing the machine.
A damaged or cracked additional handle must be
replaced. Never operate a machine with a defective
additional handle.
A damaged or cracked hand guard must be
replaced. Never operate a machine with a defective
hand guard.
Reducing dust exposure:
Some of the dust created using this power tool
may contain chemicals known to cause
cancer, allergic reaction, respiratory disease, birth
defects or other reproductive harm. Some of these
substances include: lead (in paint containing lead),
mineral dust (from bricks, concrete etc.), additives
used for wood treatment (chromate, wood
preservatives), some wood types (such as oak or
beech dust), metals, asbestos.
The risk from exposure to such substances will
depend on how long you or people nearby are
exposed to them.
Do not let particles enter the body.
Do the following to reduce exposure to these
substances: ensure good ventilation of the
workplace and wear appropriate protective
equipment, such as respirators able to filter
microscopically small particles.
Observe the relevant guidelines for your material,
staff, application and place of application (e.g.
occupational health and safety regulations,
disposal).
Collect the particles generated at the source, avoid
deposits in the surrounding area.
Use suitable accessories for special work. In this
way, fewer particles enter the environment in an
uncontrolled manner.
Use a suitable extraction unit.
Reduce dust exposure with the following measures:
- do not direct the escaping particles and the
exhaust air stream at yourself or nearby persons
or on dust deposits.
- use an extraction unit and/or air purifiers.
- ensure good ventilation of the workplace and keep
clean using a vacuum cleaner. Sweeping or
blowing stirs up dust.
- Vacuum or wash the protective clothing. Do not
blow, beat or brush.
5. Overview
See page 2.
1 Spindle locking button
2 Sliding on/off switch
3 Handle
4 Speed adjustment wheel
5 Electronic signal indicator *
6 Dust filter *
7 Bar auxiliary handle *
8 Thumb screws of the bar auxiliary handle *
9 Locking discs of the bar auxiliary handle *
10 Threaded holes on gear housing
11 Additional handle *
12 Lock button
13 Trigger
* depending on equipment/not in scope of delivery

6. Initial Operation

Before commissioning, check that the rated
mains voltage and mains frequency, as stated
on the type plate match your power supply.
Always install an RCD with a maximum trip
current of 30 mA upstream.
Always guide the angle grinder with both
hands on the handles provided.
6.1 PE 15-20 RT: Attaching the additional
handle
Always work with the auxiliary handle (11)
attached! Attach the auxiliary handle on the
left or right of the machine and secure.
6.2 Attach the bar auxiliary handle
Always work with the bar auxiliary handle (7)
attached! Fit the bar auxiliary handle (7) as
shown (see illustration A, page 2).
- Fit locking discs (9) to the left and right of the gear
housing.
- Fit the bar auxiliary handle (7) at the gear housing.
- Insert the thumb screws (8) left and right into the
bar auxiliary handle (7) and turn gently.
- Adjust the bar auxiliary handle (7) to the required
angle.
- Firmly tighten the thumb screws (8) to the left and
right manually.
6.3 Dust filter (depending on features)
Assembly see page 2, fig. B.
Regularly clean the dust filter. See chapter 9.
Cleaning.

7. Installing the tools

Press in the spindle locking knob (1) only
when the spindle is stationary!
Locking the spindle
Press in the spindle locking button (1) and turn the
spindle by hand until the spindle locking button
engages.
ENGLISH en
13