Surround Assembly; Double Door Installation - Jøtul GZ 550 DV II Acadia Installation And Operation Instructions Manual

Jøtul GZ 550 DV II

Surround Assembly

1. 1. 1. 1. 1. Cut Cut Cut and r and r emo emo emov v v v v e e e e e the plastic wir
Cut Cut and r and r and remo emo
L L L L L o o o o o w w w w w er Grille / C er Grille / C er Grille / C er Grille / Con
er Grille / C
door door door. . . . . door door
2. 2. 2. 2. 2. Install each o Install each o Install each o Install each of f f f f the Side castings Install each o the Side castings the Side castings the Side castings onto the the Side castings
cabinet by engaging the hanger tabs with the
holes in the cabinet frame. See fig. 52 for orien-
tation. You may wish to secure each side panel
to the bottom of the fireplace cabinet using the
M6 flat head screw already installed at those
locations. It will be necessary to remove the
Control Door first.
3. 3. 3. 3. 3. Install Install Install Install Install the Righ the Righ the Righ the Right t t t t and L the Righ
4 4 4 4 4 . . . . . A A A A A ttach ttach ttach the Inner P the Inner P
ttach the Inner P ttach the Inner P the Inner Panel
Inner Panel may be reversed to show the winter
scene.
(Note: Blue Black Panel is enamelled on one side only).
5 5 5 5 5 . . . . . Hang Hang the C Hang Hang Hang the C the C the C the Cen en enter Pla en en ter Pla ter Plate in position. ter Pla ter Pla
Optional Double Door
The Double Door set is fully assembled and requires
f i r e - p a r t s . c o m
no tools for installation. Use the 4 mm hex key
supplied with the doors to adjust the door alignment
at the eight socket head hinge screws.
Door Installation
Unpack the door set and inspect the parts for
damage. Notify your dealer if any damage is found.
You may wish to remove the doors from the
frame to lighten the assembly and ease installation.
They simply lift off of the hinges.
The door assembly attaches to the fireplace by
engaging the three slots in the upper frame with the
corresponding steel tabs at the top of the firebox.
See fig. 45.
A dimple located on the inside of the frame at
each lower corner engages with corresponding holes
in the glass frame to hold the bottom of the door
assembly securely to the firebox. See A, fig. 46.
1. 1. 1. 1. 1. Open the Control Access Door. Hang the door
frame onto the firebox by engaging the tabs with
the holes in the frames. See fig. 45.
2. 2. 2. 2. 2. Push the frame over to one side and engage the
dimple on that lower corner with the hole in the side of
the glass frame. You will feel it lock into place.
3. 3. 3. 3. 3. Push the frame assembly over to the opposite side
and push that lower corner down to engage with
the firebox.
22
the plastic wire e e e e tie fr the plastic wir the plastic wir tie fr tie fr om om
the plastic wir tie from tie fr om the om
ontr tr tr tr trol Door and open on on ol Door and open ol Door and open ol Door and open the the the the
on ol Door and open the
and L and L and Lef ef ef ef eft t t t t Upper Grill pla and L Upper Grill pla Upper Grill plates. Upper Grill pla Upper Grill pla
anel anel anel t t t t t o o o o o the C the C the C en en ter Pla ter Plate te te te te. . . . . The ter Pla
anel the Cen the C en enter Pla ter Pla
te in position. te in position. te in position. te in position.
the the
the the
tes. tes. tes. tes.
Figure 45. Hang the frame on the cabinet.
Figure 46. Rear view of door frame.
Figure 47. Door adjustment points.
Door Alignment Adjustment
You can adjust the door alignment if necessary by
loosening the hinge screws (See B, fig. 46 and fig. 47).
Realign the door and then tighten the screws.