Chicco KEYFIT Instructions Manual page 28

- be fitted in a front-facing position (diag.1)
- be fitted with a 3-point static or 3-point
retractor safety belt (diag.2A).
CAUTION! Never fit the child car seat into a
car seat if it is only equipped with a lap belt
(diag. 2B).
HOW TO ADJUST THE SAFETY HARNESS
WARNING! The safety harness must always
be adjusted to the size of the child's body.
Before fitting the child car seat into the car, it
is necessary to adjust the height of the child's
safety harness.
The correct position of safety harness is slight-
ly below the child's shoulders (diag. 3). The
height of the child car seat can be adjusted to
3 positions (diag. 4).
The child car seat has a mini insert which
ensures maximum protection and comfort
to children from birth up to 6 Kg of weight
(diag. 5).
Before fitting the mini insert, check that the
belts are inserted into the hole located in the
lowest position: this is the only position al-
lowed for using this accessory.
WARNING! For your child's safety: Do not
use the mini insert if the child weighs more
than 6 Kg.
INSTRUCTIONS
Components
A. Fabric cover
B. Mini insert
C. Sun canopy
D. Diagonal safety belt's side guides
E. Adjustment belt
F. Button for adjusting the safety harness
G. Safety harness' holes
H. Handle
I. Handle adjustment buttons
J. Button for locking/unlocking the child car
seat from the stroller
K. Diagonal safety belt's guide
L. Anchor-shaped hook
M. Side button for locking / unlocking the sun
canopy
N. Side elastics for fixing the fabric cover
O. Safety belts
P. Safety harness straps
Q. Safety belt's buckle
R. Button for opening the buckle
Index
• How to adjust the height of the safety har-
ness
• How to fit the child car seat into the car
• How to place the child into the child car
seat
• How to adjust the handle
• Child car seat in the bouncing or baby chair
position
• How to remove the fabric cover
• How to fit the child car seat to the stroller
HOW TO ADJUST THE HEIGHT OF THE
SAFETY HARNESS
1. Unfasten the safety harness, pressing the
red button located on the buckle (diag. 6).
2. Remove the two ends of the safety harness
from the anchor-shaped hook, as shown in
diag. 7.
3. Remove the two parts of the safety har-
ness from the front of the child car seat,
and insert them into the hole which is most
suitable to the child's height (diag. 8).
4. Re-insert the two ends of the safety har-
ness into the anchor-shaped hook (diag. 9).
Storing the Product
When it is not fitted into the car, it is recom-
mended to store the child car seat in a dry
place, away from sources of heat and to pro-
tect it from dust, humidity and direct sunlight.
HOW TO FIT THE CHILD CAR SEAT INTO
THE CAR
5. Put the child car seat's handle in a vertical
position, pressing the two side adjustment
buttons (diag. 10).
6. Place the child car seat onto the car seat
where you wish to fit it (diag. 11).
7. Pull the car safety belt and lock it into the
appropriate buckle, sliding the lap belt into
the two side guides of the child car seat
(diag. 12).
8. Hold the diagonal belt and pull it, until the
lap belt is tensioned correctly (diag. 13). At
the end of these operations, check that the
lap belt is still locked correctly into the ap-
propriate guides.
9. While keeping the diagonal belt tensioned,
slide it into the guide, located on the rear
of the backseat (diag. 14). Tension the belt
as much as possible, checking that it is not
slack or twisted.
WARNING! After fitting the child car seat, al-
ways check that car safety belt is tensioned
correctly, and that it is safely locked into its
buckle. Also check that the buckle of the car
safety belt does not come into contact with
the points where the safety belt fastens the
28