Table of Contents
Advertisement
Quick Links
Model No. NTSA03991
Serial No.
The serial number is found in the
location shown below. Write the
serial number in the space above.
Serial Number Decal
QUESTIONS?
As a manufacturer, we are
committed to providing complete
customer satisfaction. If you
have questions, or if there are
missing parts, we will guarantee
complete satisfaction through
direct assistance from our factory.
TO AVOID UNNECESSARY
DELAYS, PLEASE CALL DIRECT
TO OUR TOLL-FREE CUSTOMER
HOT LINE. The trained techni-
cians on our customer hot line
will provide immediate assis-
tance, free of charge to you.
CUSTOMER HOT LINE:
1-888-825-2588
Mon.–Fri., 6 a.m.–6 p.m. MST
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
USER'S MANUAL
Visit our website at
www.nordictrack.com
new products, prizes,
fitness tips, and much more!
Advertisement
Table of Contents
Related Manuals for NordicTrack NTSA03991
Summary of Contents for NordicTrack NTSA03991
- Page 1 Model No. NTSA03991 Serial No. The serial number is found in the location shown below. Write the serial number in the space above. Serial Number Decal QUESTIONS? As a manufacturer, we are committed to providing complete customer satisfaction. If you...
-
Page 2: Table Of Contents
Customer Hot Line at the number on the front cover for a free replacement decal. Place the new decal on the leg press accessory in the appropriate location. NordicTrack ® is a registered trademark of ICON Health & Fitness, Inc. -
Page 3: Important Precautions
Important Precautions WARNING: To reduce the risk of serious injury, read the following important precau- tions before using the leg press accessory. 1. Read all instructions in this manual before using the leg press accessory. 2. It is the responsibility of the owner to ensure that all users of the leg press accessory are informed of all precautions. -
Page 4: Part Identification Chart
Part Identification Chart Refer to the drawings below to identify small parts used in assembly. The number in parentheses by each draw- ing is the key number of the part, from the PART LIST in the center of this manual. Note: Some small parts may have been pre-attached. -
Page 5: Assembly
Assembly Make Assembly Easier for Yourself Everything in this manual is designed to ensure that the leg press accessory can be assembled successfully by anyone. Before beginning assembly, make sure to read the information on this page; this brief intro- duction will save you much more time than it takes to read it. - Page 6 Frame Assembly 1. Before beginning assembly, make sure you have read and understood the information on page 5. Open the parts bags labeled “FRAME ASSEMBLY” and “PULLEY.” Attach the Press Base (101) to the Base Support (103) with the 3/8” x 3 3/4” Carriage Bolt (119) and a 3/8”...
- Page 7 4. Slide the Press Frame (102) through the Seat Frame (106). Press a 2” Square Inner Cap (112) into the indicated end of the Press Frame (102). Press a 2” Square Angled Cap (126) onto the other end of the Press Frame.
- Page 8 Cable Assembly 8. Open the parts bag labeled “CABLE ASSEMBLY.” Attach the Cable (133) to the indicated hole in the Press Base (101) with a 3/8” x 3” Bolt (117), two 3/8” Washers (120), a 5/8” x 1/4” Spacer (127), and a 3/8” Nylon Jam Nut (122).
- Page 9 12. Wrap the Cable (133) under a 4” Pulley (113) and attach the Pulley and a Cable Trap (116) to the weld- ed bracket on the stabilizer with a 3/8” x 2” Bolt (121) and a 3/8” Nylon Locknut (118). IMPORTANT: If you are assembling the leg press accessory and your weight system at the...
- Page 10 16. Wrap the High Cable (73) around a 4” Pulley (35) in the direction shown and attach the Pulley inside the Top Frame (1) with a 3/8” x 2 1/2” Bolt (54), two 3/8” Flat Washers (55), two 5/8” x 1/2” Pulley Bushings (42), and a 3/8”...
- Page 11 Assembly Option B 13. Loosen the 1/2” Plain Nut (68) on the bolt at the end of the High Cable (73). Detach the bolt from the top of the Weight Tube (36) and the 5 7/8” Long Bushing (76). Remove the 1 1/2” Flat Washer (40) and the 5 7/8” Long Bushing (76).
- Page 12 Seat and Plate Assembly 18. Open the parts bag labeled “SEAT ASSEMBLY.” Attach the Seat (111) to the Seat Frame (106) with four 1/4” x 3/4” Bolts (130). 19. Attach the Backrest (134) to the Seat Frame (106) with four 1/4” x 3/4” Bolts (130). 20.
-
Page 13: Adjustment
Adjustment The instructions below describe how the leg press accessory can be adjusted. IMPORTANT: If there is any slack in the cables as an exercise is performed, the effectiveness of the exercise will be reduced. Adjusting the Seat To adjust the position of the Seat Frame (106), unscrew the handle of the Adjustment Knob (129) until it is loose. -
Page 14: Weight Resistance Chart
The other numbers refer to the 10 lb. weight plates. Note: The actual resistance may vary due to differ- ences in individual weight plates as well as friction between the cables, pulleys, and weight guides. Weight Plates Press (lbs.) Part List—Model No. NTSA03991 Key No. Qty. Description Press Base Press Frame... -
Page 15: Exploded Drawing
Exploded Drawing—Model No. NTSA03991 R0602A... -
Page 16: Ordering Replacement Parts
Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). To help us assist you, please be pre- pared to give the following information: • The MODEL NUMBER of the product (NTSA03991) • The NAME of the product (NordicTrack •...