Sharp FO-1660 Service Manual page 29

SW-D1 No. 1 ~ No. 4 Number of rings for auto receive
When the machine is set in the auto receive mode, the number of
rings before answering can be selected. It may be set from one to
four rings using a binary number. Since the facsimile telephone could
be used as an ordinary telephone if the handset is taken off the hook,
it should be programmed to the user's choice. If the soft switch was
set to 1, direct connection is made to the facsimile. If a facsimile
calling beep was heard when the handset is taken off the hook, press
the START key and put the handset on the hook to have the facsimile
start receiving. If it was set to 0 accidentally, receive ring is set to 1.
NOTE: If the machine is set to answer after a large number of rings, it
may not be able to receive faxes successfully. If you have
difficulty receiving faxes, reduce the number of rings to a max-
imum of 6.
SW-D1 No. 5 Automatic switching manual to auto receive mode
This soft switch is used to select whether the machine should switch
to the auto receive mode after 5 rings in the manual receive mode or
remain in the same way as SW-D1 No. 1, No. 2, No. 3 and No. 4
"0"1"0"1"(5 rings).
SW-D1 No. 6 ~ No. 8 Reserved
Set to "0".
SW-D2 No. 1 ~ No. 3 Distinctive ringing setting
When the ringing setting is turned off, all of the CI signal are received.
When any of the standard, and ring patterns 1 through 3 is selected
for the ringing setting, only the selected CI signal is received.
CI signal patterns
The CI signal patterns consists of the standard pattern, and ring
patterns 1 through 7. The standard pattern is the conventional one.
2S
STANDARD
2S
1.5S
1S
1.5S
0.5S
0.8S 0.8S
RING
PATTERN 1
for USA
0.4S
1S 1S
1S
0.3S 1S 0.3S
RING
PATTERN 2
for USA
0.2S 0.2S
0.4S 0.4S 0.8S
RING
PATTERN 3
for USA
0.2S 0.2S
1S 1S
RING
PATTERN 1
for CANADA
0.5S
0.5S 1S
RING
PATTERN 2
for CANADA
0.5S
0.5S 0.5S
RING
PATTERN 3
for CANADA
0.5S 0.5S
SW-D2 No. 4, No. 5 Reserved
Set to "0".
4S
2S
3S
4S
0.5S
4S
4S
3S
4S
4S
3.5S
0.5S
0.5S 3S
1S
3S
SW-D2 No. 6, No. 7 CI off detection timer (Distinctive ring setting
off only)
Set the minimum time period of CI signal interruption which affords to
be judged as a CI OFF section.
A
400msec
SW-D2 No. 8 Reserved
Set to "0".
SW-E1 No. 1 ~ No. 8 Reserved
Set to "0".
SW-E2 No. 1 ~ No. 8 Reserved
Set to "0".
SW-F1 No. 1, No. 2 DTMF detect time
Used to set detect time of DTMF (Dual Tone Multi Frequency) used in
remote reception (5
The longer the detect time is, the less the error detection is caused by
noises.
SW-F1 No. 3 Protection of remote
Used to set the function of remote reception (5
the remote reception function is disabled.
SW-F1 No. 4 Remote reception with GE telephone
(Corresponding to TEL made by GE) P. B. X.
"1": Compatible with TEL mode by GE
"0": Not compatible
•
When sending (5
tured telephone remote reception may not take place because of
special specifications in their DTMF.
To overcome this, a soft SW is provided to change the modem
setting to allow for remote reception.
•
If this soft SW is set to "1", other telephone sets may be adversely
affected.
SW-F1 No. 5 ~ No. 8 Remote operation code figure by external
TEL (0 ~ 9)
Remote operation codes can be changes from 0 through 9. If set to
greater than 9, it defaults to 9. The "5
Ex-7 (Default: 5
SW-F2 No. 1 CNG detection in STAND-BY mode
When setting to "1", the CNG signal detection function during standby
stops.
SW-F2 No. 2, No. 3 Number of CNG detect (AM mode)
Used for detection of CNG in 1 to 4 pulses.
SW-F2 No. 4, No. 5 Number of CNG (STAND-BY mode)
Used for detection of CNG in 1 to 4 pulses.
SW-F2 No. 6 ~ No. 8 Reserved
Set to "0".
SW-G1 No. 1 ~ No. 4 Quiet detect time
When an answering machine is connected, if a no sound state is
detected for a certain period of time, the machine judges it as a
transmission from a facsimile machine and automatically switches to
the FAX mode.
SW-G1 No. 5 ~ No. 8 Quiet detect start timing
Inserts a pause before commencing quiet detection.
SW-G2 No. 1 ~ No. 8 Reserved
Set to "0".
2 – 14
UX-600MU/MC
FO-1660U/C
1
2000msec 2
).
). When set to "1",
) for remote reception with a GE manufac-
" is not changed.
)
B