(including damages for loss of profits, loss of business, loss of data, interruption of business and the like), even if ASRock has been advised of the possibility of such damages arising from any defect or error in the documentation or product.
Page 3
If you require assistance please call ASRock Tel : +886-2-28965588 ext.123 (Standard International call charges apply) The terms HDMI™...
Important Safety Instructions Pay close attention to the following safety instructions before performing any of the operation. Basic safety precautions should be followed to protect yourself from harm and the product from damage: • Operation of the product should be carried out by suitably trained, qualified, and certified personnel only to avoid risk of injury from electrical shock or energy hazard.
Contact Information If you need to contact ASRock or want to know more about ASRock, you’re welcome to visit ASRock’s website at http://www.asrock.com; or you may contact your dealer for further information. For technical questions, please submit a support request form at http://www.asrock.com/support/tsd.asp...
In case any modifications of this documentation occur, the updated version will be available on ASRock’s website without further notice. If you require technical support related to this product, please visit our website for specific information about the model you are using.
• Storm Black Material • Steel Body / Aluminum + Plastic Dimension • 372mm (W) x 123mm (H) x 400mm (L) • ASRock Z87-M8 Motherboard • Supports 4 Gen Intel® Core i7 / i5 / i3 / Xeon® / Pentium® / Celeron® Processor Family Memory • Supports DDR3 1600/1333/1066 MHz, 2 x SO-DIMM...
Page 8
* Max. Supported VGA Dimension: 290mm x 137mm x 43.5mm; Max. Supported TDP: 200W (If you use a graphics card with over 200W TDP, please note that the system’s power supply is only 450W.)
LED, FAN-Tastic Tuning, OC Tweaker and a whole lot more. ASRock Instant Flash ASRock Instant Flash is a BIOS flash utility embedded in Flash ROM. This conve- nient BIOS update tool allows you to update the system BIOS in a few clicks without preparing an additional floppy diskette or other complicated flash utility.
Page 10
And it also boosts the speed of Adobe Photoshop 5 times faster. Another advantage of ASRock XFast RAM is that it reduces the frequency of accessing your SSDs or HDDs in order to extend their lifespan.
Page 11
Windows® 8 brings the ultimate boot up experience. The lightning boot up speed makes it hard to access the UEFI setup. ASRock Restart to UEFI allows users to enter the UEFI automatically when turning on the PC. By enabling this function, the PC will enter the UEFI directly after you restart.
Page 12
ASRock Easy Driver Installer For users that don’t have an optical disk drive to install the drivers from our support CD, Easy Driver Installer is a handy tool in the UEFI that installs the LAN driver to your system via an USB storage device, then downloads and installs the other required drivers...
Chapter 2 Product Overview This chapter provides diagrams showing the location of important components of the M8. 2.1 Front View Description A-Command (All-In-One OLED Button) Optical disk drive eject button 4 x USB 3.0 ports 4-in-1 Card reader (SD3.0/MMC/MS/MS PRO) Microphone jack Headphone jack...
Page 14
2.1.1 The Function of A-Command The A-Command is a multipurpose controller knob which is used to cycle through various functions. Controlling A-Command • Rotate the knob to toggle among main functions or options. • Press once to confirm your selection. Powering on the System Press A-Command to turn on the system power.
Off: Toggle off the light in the case All off: Toggle off the light in the case; enable the Good Night LED function *ASRock Good Night LED technology offers you a better sleeping environment by extinguishing the unessential LEDs. By enabling Good Night LED, the Power/HDD LEDs will be switched off when the system is powered on.
Page 18
No. Description No. Description Line In port (light blue) eSATA2 port** Line Out port (lime) DisplayPort Center/Subwoofer port (orange) HDMI port Rear Speaker Out port (black) USB3.0 port LAN RJ-45 port* (Intel Gigabit LAN) 14 USB3.0 port USB2.0 ports USB3.0 port USB2.0 ports USB3.0 port USB2.0 ports...
2.3 Inside View Description Riser card retention bracket VGA card holder Hard disk drive tray (compatible with 4 x 2.5" HDD or 1 x 3.5 HDD) ODD + 2.5" HDD Tray (compatible with 1 x slot-in ODD and 1 x 2.5" HDD) Power supply unit (450W) Power panel connector SATA 3.0 connectors...
Page 20
Front audio connector USB3.0 connector Auxiliary fan connector 2T2R WiFi Module (802.11ac) CPU socket DIMM sockets Chassis fan connector ATX 12V power connector Hard drives are not included with this system.
Chapter 3 Hardware Installation This chapter helps you assemble the chassis and install components. Please follow the installation procedures listed below. Installation Procedures Removing the side panels Removing the top cover Removing the VGA card holder Removing the riser card Installing the hard drives Installing the CPU Installing the CPU Fan and CPU Cooler...
Page 22
3.1 Installing System Components 3.1.1 Removing the Side Panels To remove the side panels, you have to unlock the keylock on the top cover using the system key. Before unlocking, power off the system and unplug the power cord. After the side panel are replaced, make sure to lock the keylock on the top cover and then power on the system.
3.1.2 Removing the Top Cover 1. To remove the top cover, you have to follow the procedures below: 1) Power off the system and unplug the power cord. 2) Unlock the keylock on the top cover using the system key. 3) Follow the instructions in Section 3.1 to remove the right side panel.
Page 24
5. Draw out the mounting bracket from the chassis. 6. Follow the instructions in Section 3.1 to release the left side panel. 7. Release the top cover. Slide the top cover toward the front of the system until it releases. Lift up the top cover.
Page 25
3.1.3 Removing the VGA Card Holder To remove the VGA card holder, you have to remove the side panels and top cover, giving you access to the VGA card holder inside. 1. Remove the VGA card holder. Remove the two screws that hold the VGA card holder in place. Lift the VGA card holder up and off the chassis.
3.1.4 Removing the Riser Card 1. Remove the riser card. Remove the two screws securing the riser card retention bracket. Grasp the riser card by its edges, and carefully pull it from the expansion slot.
3.1.5 Installing the Hard Drives 3.1.5.1 Installing the Hard Drive(s) to the Drive Tray Assembly 1. To install the hard drives, you have to remove the VGA card holder and the riser card , giving you access to the drive tray assembly inside. 2.
Page 28
2. Take apart the drive tray assembly. Remove the screws that secure the bottom HDD tray with the top tray. Take the assembly apart. 3. Install a 3.5" HDD or up to four 2.5" HDD. Installing a 3.5-Inch Hard Drive: Set the top tray aside.
Page 29
Installing up to Four 2.5-Inch Hard Drive Place the first 2.5" HDD to the bottom HDD tray and secure the hard drive using the four screws (two on the sides and two in the rear). Place the second 2.5" HDD to the top HDD tray and secure the hard drive using the four screws.
3.1.5.2 Installing the Hard Drive to the ODD + 2.5" HDD Tray 1. To install the hard drives, you have to remove the PSU. 2. The ODD + 2.5” HDD Tray fits a slim slot-in optical disk drive (ODD) and a 2.5-inch hard drives.
Page 31
2. Remove the ODD+2.5" HDD Tray. Unplug the ODD SATA power connector. Remove the five screws securing the ODD + 2.5" HDD Tray to the chassis. Lift the tray off the chassis. 3. Place a 2.5" HDD to the HDD tray and secure the hard drive using the four screws (four in the rear).
Page 32
4. Align the screw holes on the ODD + 2.5" HDD Tray with the screw holes on the chassis. Fasten the five screws. 5. Connect the power and SATA data cables and the ODD SATA power connector. 6. Re-install the PSU. Align the PSU with the starting line and then slide the PSU to the left until it reaches the end line.
3.1.6 Replacing the ODD 1. Follow the instructions in section 3.1.5.2 to remove the power supply unit and lift the tray off the chassis. 2. Remove the old optical disk drive. 3. Slide a new optical disk drive into the ODD tray. 4.
3.1.7 Installing the CPU 1. Before you insert the 1150-Pin CPU into the socket, please check if the PnP cap is on the socket, if the CPU surface is unclean, or if there are any bent pins in the socket. Do not force to insert the CPU into the socket if above situation is found.
Page 36
Please save and replace the cover if the processor is removed. The cover must be placed if you wish to return the motherboard for after service.
Page 37
3.1.8 Installing the CPU Fan and CPU Cooler...
Page 38
1. Make sure to evenly spread the thermal paste over the CPU to improve heat dissipation. 2. Ensure that the CPU and the CPU cooler are securely fastened and in good contact with each other. 3. To make sure the CPU cooler is seated properly, it is highly recommended to check whether or not the CPU temperature reported in the BIOS is at a normal level.
3.1.9 Installing Memory Modules (SO-DIMM) This motherboard provides two 204-pin DDR3 (Double Data Rate 3) SO-DIMM slots. It is not allowed to install a DDR or DDR2 memory module into a DDR3 slot; otherwise, this motherboard and SO-DIMM may be damaged. The DIMM only fits in one correct orientation.
Page 41
3.2 Replacing System Components 3.2.1 Replacing the Riser Card 1. Replace the riser card. Align the riser card keys correctly with the expansion slot on the system board and insert it into place. Fasten the two screws securing the riser card retention bracket.
3.2.2 Installing the Graphics Card The M8 chassis supports both single-slot graphics card and dual-slot graphics card. Before graphics card installation, please lift the VGA card holder and make sure the riser card is installed properly. 1. Open the latch of the VGA card holder and remove the screws that secures the slot cover.
Page 43
5. Engage the VGA card holder with the two vertical sliding tracks while sliding it back to the chassis. 6. Make sure the VGA card holder is secured by the tongue plate and the graphics card is seated correctly. 7. Secure the VGA card holder with the chassis using the two screws previously removed.
3.2.3 Replacing the Top Cover 1. Place the system in an upright position. 2. Make sure to release the left side panel. 3. Connect the 4-pin top fan connector. 4. Replace the top cover. Replace the top cover onto the chassis. Slide the top cover toward the rear of the system until it clicks into place.
Page 45
5. Insert the mounting bracket into the mounting holes. 6. Secure it to the case with the three screws previously removed.
3.2.1 Replacing the Side Panels 1. Place the system in an upright position. 2. Replace the side panels. Snap the right side panel into place. Snap the left side panel into place. 3. Lock the system keylock on the top cover.
4.2 Jumpers Setup The illustration shows how jumpers are setup. When the jumper cap is placed on the pins, the jumper is “Short”. If no jumper cap is placed on the pins, the jumper is “Open”. The illustration shows a 3-pin jumper whose pin1 and pin2 are “Short” when a jumper cap is placed on these 2 pins.
4.3 Onboard Headers and Connectors Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over these headers and connectors. Placing jumper caps over the headers and connectors will cause permanent damage to the motherboard. System Panel Header Connect the power HDLED+ PLED+...
Page 51
Serial ATA3 Connectors These six SATA3 SATA3_1 (SATA3_1) connectors support SATA (SATA3_2) data cables for internal SATA3_2 (SATA3_5) storage devices with up to (SATA3_6) 6.0 Gb/s data transfer rate. SATA3_5 (SATA3_3) SATA3_4 connector is (SATA3_4) shared with the eSATA SATA3_6 (see p.41, No.
Page 52
Front Panel Audio Header This header is for MIC2_L MIC2_R (9-pin HD_AUDIO1) OUT2_R connecting audio devices J_SENSE (see p.41, No. 9) to the front audio panel. OUT2_L OUT_RET MIC_RET PRESENCE# GN D 1. High Definition Audio supports Jack Sensing, but the panel wire on the chassis must sup- port HDA to function correctly.
Page 53
ATX Power Connector This motherboard pro- (24-pin ATXPWR1) vides a 24-pin ATX power (see p.41, No. 5) connector. To use a 20-pin ATX power supply, please plug it along Pin 1 and Pin ATX 12V Power This motherboard Connector provides a 4-pin ATX 12V (4-pin ATX12V1) power connector.
Chapter 5 Software and Utilities Operation 5.1 Installing Drivers The Support CD that comes with the M8 contains necessary drivers and useful utilities that enhance the M8’s features. Running The Support CD To begin using the support CD, insert the CD into your CD-ROM drive. The CD automatically displays the Main Menu if “AUTORUN”...
5.2 A-Tuning A-Tuning is ASRock’s multi purpose software suite with a new interface, more new features and improved utilities, including XFast RAM, Dehumidifier, Good Night LED, FAN-Tastic Tuning, OC Tweaker and a whole lot more. 5.2.1 Installing A-Tuning When you install the all-in-one driver to your system from ASRock’s support CD, A-Tuning will be auto-installed as well.
Page 56
Tools Various tools and utilities. XFast RAM Boost the system’s performance and extend the HDD’s or SDD’s lifespan! Create a hidden partition, then assign which files should be stored in the RAM drive. XFast LAN Boost the speed of your internet connection! Select a specific mode for making the designated program's priority highest.
Page 57
Dehumidifier Prevent motherboard damages due to dampness. Enable this function and configure the period of time until the computer powers on, and the duration of the dehumidifying process. Key Master Enhance your mouse and keyboard with customizable macros, sniper modes, scroll speed, key repeat rates and repeat delay.
Page 61
5.3 SBX Pro Studio This section explains how to configure the Creative Sound Core3D using SBX Pro Studio. Click the power button on the left to activate or deactivate. Surround Control the level of audio immersion in music, movies and games. Crystalizer Enhance music and movies to make them sound livelier.
Page 62
CRYSTALVOICE Select a recording device Mic Volume Control the level of mic volume. Mic Boost Control the level of mic boost. CrystalVoice Click the power button on the left to activate or deactivate. Morph your voice into different characters and accents. Smart Volume Be heard clearly without having to shout or whisper.
Page 63
SCOUT MODE Scout Mode Enable or disable scout mode. This proprietary technology allows you to hear your enemies from further away, giving you a distinct tactical advantage in combat. Hot Key Configuration Configure hot keys to enable or disable scout mode.
Page 64
SPEAKERS/HEADPHONES Speakers / Headphones Configuration Select the device connected. If there are both speakers and front headphones connected, please select the device you desire to use as audio output. Optional Speakers Center Enable or disable center speaker. Subwoofer Enable or disable subwoofer. Rear pair Enable or disable rear pair speakers.
Page 65
Bass Management Bass Redirection Enable or disable bass redirection. Subwoofer Gain Enable or disable subwoofer gain. Crossover Frequency Redirect all frequencies below this value to the optimal speaker for better bass response. MIXER Playback Speakers Control the level of speakers playback. SPDIF-Out Control the level of SPDIF-Out playback.
Page 66
What U Hear Control the level of playback redirect. EQUALIZER Choose from Flat, Acoustic, Classical, Country, Dance, Jazz, New Age, Pop, Rock and Vocal. JACK SETUP Device Connected: Select the device connected. Show Jack Setup dialog when an audio jack is inserted Enable or disable Jack Setup dialog.
Page 67
ADVANCED FEATURES Play stereo mix to digital output Enable or disable play stereo mix to digital output. PROFILE...
Page 68
User Profiles You can save, load or delete your user profiles. The default is <Custom>. Note If you want to hear your own voice through the microphone (Playback mode). You can change your settings to "playback mode" by checking the "Listen to this device"...
5.4 Intel® Rapid Start Technology Intel® Rapid Start Technology enables your system to wake up faster from deep sleep, saving time and power consumption. Feel secure to know that your system will resume to working condition even if an unexpected power loss happens while the PC is in sleep mode.
Page 70
5.4.2 Setup Guide Configuring Rapid Start Step 1 Run ASRock Rapid Start utility from Start -> All Programs -> ASRock Utility. Step 2 If you have more than one hard drives in your system, you must select one, then choose the Partition Size desired for your hidden partition and click on Create. The system will automatically create a hidden partition according to your settings.
Page 71
Step 3 When prompted to restart after the setup, click Yes to reboot. Step 4 Double-click the Intel® Rapid Start Technology Manager icon in the Windows system tray.
Page 72
Step 5 Make sure Rapid Start is on. Drag the slider to configure the time. For example, if the timer value is set to ten minutes, the system will enable Rapid Start mode after entering sleep state for ten minutes. If the timer is set to 0 minutes, Windows will immediately enable Rapid Start mode as it enters sleep state.
Page 73
will automatically wake up and enable Rapid Start mode after entering sleep state for a period of time. The power of the computer in Rapid Start mode can be cut off, it will not cause data loss of the programs or files you were executing before entering sleep state.
5.5 Intel® Smart Connect Technology Intel® Smart Connect Technology is a feature that periodically wakes your computer from Windows® sleep state to refresh email or social networking applications. It saves your waiting time and keeps the content always up-to-date. 5.5.1 System Requirements •...
Page 75
Installing ASRock Smart Connect Utility Step 1 Install ASRock Smart Connect Utility, which is located in the folder at the following path of the Support CD: \ ASRock Utility > Smart Connect. Step 2 Once installed, run ASRock Smart Connect from your desktop or go to Windows Start -> All Programs -> ASRock Utility.
Page 76
Step 3 Click the Add button. Take Foxmail as an example, add Foxmail to the Application list. Step 4 Select Foxmail from the Application List, then click the arrow pointing right to add this application to the Smart Connect List. Step 5 Click Apply to enable Smart Connect.
Page 77
Step 6 Double-click the Intel® Smart Connect Technology Manager icon in the Windows system tray. Step 7 Drag the slider to configure how often the system will connect to the network to download updates. Shorter durations will provide more frequent updates, but may cause more power consumption.
Page 78
The system will wake up from sleep state periodically, and then start to update Foxmail. The screen will not display anything so the computer can maintain minimum power usage. Afterwards, the system will automatically return to sleep state again. Upon waking up the system, you will find the new mail that were sent to you during sleep state are already updated and ready to be read in Foxmail.
5.6 Intel® Remote Wake Technology Intel® Remote Wake Technology allows you to use programs or services over the Internet to wake up your home computer from energy efficient sleep mode. Before configuring this feature, verify the following. • Remote Wake has been enabled in "Intel® Smart Connect Technology Manager".
Page 80
Step 2 Click the "My Account" tab. Then click on "New" to create a new mesh. Step 3 A new mesh window will pop up. Enter a mesh name and password. Step 4 Select all the checkboxes and click Create Mesh. Downloading and Installing Mesh Agent Step 1 Click Install on the My Account page.
Page 81
Step 4 Click Install / Update. Step 5 Wait a minute for the New Machine to appear in "My Device".
Page 82
Step 6 Check whether "Intel Remote Wake" appeared or not. Waking up Your PC using PC Step 1 On the "My Devices" page, click on Power Actions. Step 2 Click on Wake or Sleep.
Page 83
Waking up Your PC Using Mobile Device Before waking up your home computer using a mobile device, please log out of MeshCentral on other previously used computers or devices. Step 1 Login to meshcentral.com/m. Step 2 Select a Machine. Step 3 Click on Wake or Sleep.
Page 84
Step 1 Download and install the Streamer on your home computer, which is located in the folder at the following path of the Support CD: \ ASRock Utility > Splashtop Streamer. Then enter your Splashtop Account. If you have not created a Splashtop acount, create one.
Using Remote Control Step 1 In "Splashtop 2”, tap an online machine from the list to connect to your home computer. Step 2 Start remotely accessing your home computer. The functionality and price of the Splashtop APP and subscription fee is subject to change.
Page 87
5.7.1 Installing Start8 Install Start8, which is located in the folder at the following path of the Support CD: \ ASRock Utility > Start8. 5.7.2 Configuring Start8 Style Select between the Windows 7 style and Windows 8 style Start Menu. Then select...
Page 88
Configure Configure provides configuration options, including icon sizes, which shortcuts you want Start Menu to display, quick access to recently used apps, the functionality of the power button, and more. Control...
Page 89
Control lets you configure what a click on the start button or a press on the Windows key does. Desktop Desktop allows you to disable the hot corners when you are working on the desktop. It also lets you choose whether or not the system boots directly into desktop mode and bypass the Metro user interface.
Page 90
5.8 XSplit Broadcaster XSplit Broadcaster is a desktop application designed to make your gameplay broadcasting, live-streaming and recording a lot easier and more fun to do, we are giving away the 3 months premium license which is worth US$24.95 for free! 5.8.1 Live Streaming Your Gameplay Step 1 Go to Start > All Programs > XSplit > XSplit Broadcaster to launch it.
Page 91
Step 3 Go to Broadcast > Add Channels…. Step 4 Click Add..Step 5 Select a platform for live streaming. *Before you start streaming, you need to register an account for the streaming service website, such as Twitch.tv, USTREAM, or other livestreaming services.
Page 92
Step 6 Fill in your platform's Username and Password. Based on your needs, configure the Video and Audio Encoding settings. Click OK. Step 7 The channel then appears in your broadcast list. Click Apply and OK to save the settings.
Page 93
Step 8 Go to Broadcast and select the platform to enable live streaming. A link to view your live Broadcast has been copied for you automatically. Simply press CTRL-V or right click and choose Paste to paste the link into the browser, and you can see your broadcast.
Chapter 6 UEFI SETUP UTILITY 6.1 Introduction ASRock Interactive UEFI is a blend of system configuration tools, cool sound effects and stunning visuals. Not only will it make BIOS setup less difficult but also a lot more amusing. This section explains how to use the UEFI SETUP UTILITY to configure your system.
6.1.2 Navigation Keys Use < > key or < > key to choose among the selections on the menu bar, and use < > key or < > key to move the cursor up or down to select items, then press <Enter>...
When you enter the UEFI SETUP UTILITY, the Main screen will appear and display the system overview. Active Page on Entry Select the default page when entering the UEFI setup utility. UEFI Guide UEFI Guide is a quick tutorial for ASRock's UEFI setup Utility. You may abort the tutorial by pressing "esc".
6.3 OC Tweaker Screen In the OC Tweaker screen, you can set up overclocking features. Because the UEFI software is constantly being updated, the following UEFI setup screens and descriptions are for reference purpose only, and they may not exactly match what you see on your screen.
CPU Cache Ratio The CPU Internal Bus Speed Ratio. The maximum should be the same as the CPU Ratio. BCLK/PCIE Frequency The CPU speed is determined by the CPU Ratio multiplied with the BCLK. Increasing the BCLK will increase the internal CPU clock speed but also affect the clock speed of other components.
Page 99
Short Duration Power Limit Configure Package Power Limit 2 in watts. When the limit is exceeded, the CPU ratio will be lowered immediately. A lower limit can protect the CPU and save power, while a higher limit may improve performance. Primary Plane Current Limit Configure the current limit of the CPU under Turbo Mode in ampere.
DRAM Configuration DRAM Tweaker Fine tune the DRAM settings by leaving marks in checkboxes. Click OK to confirm and apply your new settings. CAS# Latency (tCL) The time between sending a column address to the memory and the beginning of the data in response.
Page 101
RAS# Active Time (tRAS) The number of clock cycles required between a bank active command and issuing the precharge command. Command Rate (CR) The delay between when a memory chip is selected and when the first active command can be issued. Write Recovery Time (tWR) The amount of delay that must elapse after the completion of a valid write operation, before an active bank can be precharged.
Page 102
tREFI Configure refresh cycles at an average periodic interval. tCKE Configure the period of time the DDR3 initiates a minimum of one refresh command internally once it enters Self-Refresh mode. tRDRD Configure between module read to read delay. tRDRDDR Configure between module read to read delay from different ranks. tRDRDDD Use this to change DRAM tRWSR Auto/Manual settings.
Page 103
tRDWR Configure between module read to write delay. tRDWRDR Configure between module read to write delay from different ranks. tRDWRDD Configure between module read to write delay from different DIMMs. RTL (CHA) Configure round trip latency for channel A. RTL (CHB) Configure round trip latency for channel B.
Page 104
Command Tri State Enable for DRAM power saving. MRC Fast Boot Enable Memory Fast Boot to skip DRAM memory training for booting faster. FIVR Configuration FIVR Switch Frequency Signature Select whether to boost or lower the FIVR Switch Frequency. FIVR Switch Frequency Offset Configure the percentage of frequency boost or deduction.
CPU Cache Voltage Offset Configure the voltage for the CPU Cache. Setting the voltage higher may increase system stability when overclocking. System Agent Voltage Offset Configure the voltage for the System Agent. Setting the voltage higher may increase system stability when overclocking. CPU Analog IO Voltage Offset CPU I/O Analog Voltage.
DRAM Voltage Use this to configure DRAM Voltage. The default value is [Auto]. PCH 1.05V Voltage Chipset 1.05V Voltage. Use default settings for best performance. PCH 1.5V Voltage I/O 1.5V Voltage. Use default settings for best performance.
6.4 Advanced Screen In this section, you may set the configurations for the following items: CPU Configu- ration, Chipset Configuration, Storage Configuration, Intel® Rapid Start Technology, Intel® Smart Connect Technology, ACPI Configuration and USB Configuration. Setting wrong values in this section may cause the system to malfunction.
6.4.1 CPU Configuration Active Processor Cores Select the number of cores to enable in each processor package. CPU C States Support Enable CPU C States Support for power saving. It is recommended to keep C3, C6 and C7 all enabled for better power saving. Enhanced Halt State (C1E) Enable Enhanced Halt State (C1E) for lower power consumption.
Page 109
Package C State Support Enable CPU, PCIe, Memory, Graphics C State Support for power saving. CPU Thermal Throttling Enable CPU internal thermal control mechanisms to keep the CPU from overheat- ing. No-Execute Memory Protection Processors with No-Execution Memory Protection Technology may prevent certain classes of malicious buffer overflow attacks.
6.4.2 Chipset Configuration Primary Graphics Adapter Select a primary VGA. VT-d Intel® Virtualization Technology for Directed I/O helps your virtual machine monitor better utilize hardware by improving application compatibility and reliability, and providing additional levels of manageability, security, isolation, and I/O performance.
Page 111
Render Standby Power down the render unit when the GPU is idle for lower power consumption. Onboard HD Audio Enable/disable onboard HD audio. Set to Auto to enable onboard HD audio and automatically disable it when a sound card is installed. Front Panel Enable/disable front panel HD audio.
6.4.3 Storage Configuration SATA Controller(s) Enable/disable the SATA controllers. SATA Mode Selection IDE: For better compatibility. AHCI: Supports new features that improve performance. RAID: Combine multiple disk drives into a logical unit. AHCI (Advanced Host Controller Interface) supports NCQ and other new features that will improve SATA disk performance but IDE mode does not have these advantages.
Page 113
Dynamic Storage Accelerator Keep this option enabled for higher HDD and SDD I/O performance, lower latency and increased system responsiveness. Hard Disk S.M.A.R.T. S.M.A.R.T stands for Self-Monitoring, Analysis, and Reporting Technology. It is a monitoring system for computer hard disk drives to detect and report on various indicators of reliability.
Page 114
6.4.4 Intel® Rapid Start Technology ® Intel Rapid Start Technology Intel® Rapid Start Technology is a new zero power hibernation mode which allows users to resume in just 5-6 seconds.
Page 115
6.4.5 Intel® Smart Connect Technology ® Intel Smart Connect Technology ® Intel Smart Connect Technology automatically updates your email and social networks, such as Twitter, Facebook, etc. while the computer is in sleep mode.
6.4.6 ACPI Configuration Suspend to RAM It is recommended to select auto for ACPI S3 power saving. Check Ready Bit Enable to enter the operating system after S3 only when the hard disk is ready, this is recommended for better system stability. ACPI HPET Table Enable the High Precision Event Timer for better performance and to pass WHQL tests.
Page 117
RTC Alarm Power On Allow the system to be waked up by the real time clock alarm. Set it to By OS to let it be handled by your operating system. USB Keyboard/Remote Power On Allow the system to be waked up by an USB keyboard or remote controller. USB Mouse Power On Allow the system to be waked up by an USB mouse.
6.4.7 USB Configuration USB Controller Enable or disable all the USB ports. USB 3.0 Controller Enable or disable all the USB 3.0 ports. Legacy USB Support Enable or disable Legacy OS Support for USB 2.0 devices. If you encounter USB compatibility issues it is recommended to disable legacy USB support.
Page 119
In order to prevent users from bypassing OMG, guest accounts without permission to modify the system time are required. UEFI Tech Service Contact ASRock Tech Service if you are having trouble with your PC. Please setup network configuration before using UEFI Tech Service. Easy RAID Installer Easy RAID Installer helps you to copy the RAID driver from the support CD to your USB storage device.
Save UEFI files in your USB storage device and run Instant Flash to update your UEFI. Internet Flash ASRock Internet Flash downloads and updates the latest UEFI firmware version from our servers for you. Please setup network configuration before using Internet Flash.
Page 121
UEFI Download Server Select a server to download the UEFI firmware. Dehumidifier Function If Dehumidifier Function is enabled, the computer will power on automatically to dehumidify the system after entering S4/S5 state. Dehumidifier Period Configure the period of time until the computer powers on and enables Dehumidifier after entering S4/S5 state.
6.6 Hardware Health Event Monitoring Screen This section allows you to monitor the status of the hardware on your system, including the parameters of the CPU temperature, motherboard temperature, fan speed and voltage. CPU Fan 1 Setting Select a fan mode for CPU Fans 1, or choose Customize to set 5 CPU temperatures and assign a respective fan speed for each temperature.
6.7 Boot Screen This section displays the available devices on your system for you to configure the boot settings and the boot priority. Fast Boot Fast Boot minimizes your computer's boot time. In fast mode you may not boot from an USB storage device. Ultra Fast mode is only supported by Windows 8 and the VBIOS must support UEFI GOP if you are using an external graphics card.
Page 124
Boot Beep Select whether the Boot Beep should be turned on or off when the system boots up. Please note that a buzzer is needed. Full Screen Logo Enable to display the boot logo or disable to show normal POST messages. AddOn ROM Display Enable AddOn ROM Display to see the AddOn ROM messages or configure the AddOn ROM if you've enabled Full Screen Logo.
Page 125
Enable to launch the Compatibility Support Module. Please do not disable unless you’re running a WHCK test. If you are using Windows 8 64-bit and all of your devices support UEFI, you may also disable CSM for faster boot speed. Launch PXE OpROM Policy Select UEFI only to run those that support UEFI option ROM only.
6.8 Security Screen In this section you may set or change the supervisor/user password for the system. You may also clear the user password. Supervisor Password Set or change the password for the administrator account. Only the administrator has authority to change the settings in the UEFI Setup Utility. Leave it blank and press enter to remove the password.
6.9 Exit Screen Save Changes and Exit When you select this option the following message, “Save configuration changes and exit setup?” will pop out. Select [OK] to save changes and exit the UEFI SETUP UTILITY. Discard Changes and Exit When you select this option the following message, “Discard changes and exit setup?”...
Page 132
開啟 / 關閉機殼內的燈光,或啟用 Good Night LED ( 晚安 LED) 功能 *。 開:開啟機殼內的燈光 關:關閉機殼內的燈光 全關:關閉機殼內的燈光;啟用 Good Night LED ( 晚安 LED) 功能 *ASRock Good Night LED ( 晚安 LED) 技術會將不必要的 LED 關閉,以 營造更好的睡眠環境。啟用 Good Night LED ( 晚安 LED) 後,電源 /HDD LED 將在系統開啟時關閉。系統進入待命/休眠模式時,Good Night LED ( 晚安 LED) 功能也會自動關閉電源及鍵盤 LED。...
Page 146
2.3 内视图 编号 说明 转接卡固定支架 VGA 卡固定器 硬盘托盘(兼容 4 x 2.5" HDD 或 1 x 3.5 HDD) ODD + 2.5" HDD 托盘 (兼容 1 x 吸入式 ODD 和 1 x 2.5" HDD) 电源装置 (450W) 系统面板接脚 SATA 3.0 接口 USB 2.0 接脚 PCIe 槽...
Page 147
USB 3.0 接脚 辅助风扇接口 2T2R WiFi 模块 (802.11ac) CPU 插槽 DIMM 插槽 机箱风扇接口 ATX 12V 电源接口 此系统中未包括硬盘。...
Page 148
1 Einleitung Vielen Dank, dass Sie sich für das M8 entschieden haben – ein zuverlässiges Gaming- Barebone-System, das konsequent unter der strengen Qualitätskontrolle von ASRock hergestellt wurde. Es liefert ausgezeichnete Leistung mit robustem Design, das ASRocks Streben nach Qualität und Beständigkeit erfüllt.
Page 149
• Stahlgehäuse / Aluminium + Kunststoff Abmessungen • 372 mm (B) x 123 mm (H) x 400 mm (L) Motherboard • ASRock Z87-M8 Prozessor • Unterstützt Intel® Core -Prozessorfamilie i7 / i5 / i3 / Xeon® / Pentium® / Celeron® der 4. Generation • Unterstützt DDR3 1600/1333/1066 MHz, 2 x SO-DIMM-...
Page 150
2 Produktübersicht Dieses Kapitel enthält Abbildungen mit den Positionen wichtiger Komponenten des 2.1 Vorderseite Beschreibung A-Command (Alles-in-Einem-OLED-Taste) Auswurftaste des optischen LaufwerksA-Command 4 x USB 3.0-Ports 4-in-1-Kartenleser (SD 3.0/MMC/MS/MS PRO) Mikrofonanschluss Kopfhöreranschluss...
Page 151
2.1.1 Die Funktion von A-Command Der A-Command ist ein Mehrzweckkontrollregler zum Umschalten zwischen verschiedenen Funktionen. A-Command steuern • Drehen Sie den Knopf zum Umschalten zwischen Hauptfunktionen und Optionen. • Drücken Sie zum Bestätigen Ihrer Auswahl einmal. System einschalten Drücken Sie zum Einschalten des Systems A-Command. Warten Sie, bis das Betriebssystem automatisch lädt.
Page 152
Ein: Licht im Gehäuse einschalten Aus: Licht im Gehäuse ausschalten Alles aus: Licht im Gehäuse ausschalten; Good Night LED-Funktion aktivieren *ASRock Good Night LED-Technologie bietet Ihnen eine bessere Schlafumgebung durch Abschaltung nicht benötigter LEDs. Durch Aktivierung von Good Night LED werden Betriebsanzeige/Festplatten-LEDs abgeschaltet, wenn das System eingeschaltet ist.
Page 155
Nr. Beschreibung Beschreibung Line-In-Port (hellblau) eSATA2-Port** Line-Out-Port (grün) DisplayPort Center/Subwoofer-Port (orange) HDMI-Port Rückseitiger Lautsprecherausgang USB 3.0-Port (schwarz) LAN-RJ-45-Port* (Intel-Gigabit-LAN) 14 USB 3.0-Port USB 2.0-Ports USB 3.0-Port USB 2.0-Ports USB 3.0-Port USB 2.0-Ports Optischer SPDIF-Ausgang USB 2.0-Ports Mikrofonanschluss (rosa) * Es gibt zwei LEDs am LAN-Port. Bitte beachten Sie die nachstehende Tabelle zur Identifikation der LAN-Port-LED. Geschwindigkeits-LED Aktivitäts-/Verbindungs-LED LAN-Port...
Page 156
2.3 Innenseite Beschreibung Riser-Kartenhalterung VGA-Kartenhalterung Festplatteneinschub (kompatibel mit vier 2,5-Zoll-Festplatten oder 1 x 3,5-Zoll- Festplatte) ODD- + 2,5-Zoll-Festplatteneinschub (kompatibel mit einem optischem Slot-In-Laufwerk und einer 2,5-Zoll-Festplatte) Netzteil (450 W) Systemblende-Stileiste SATA 3.0-Anschlüsse USB 2.0-Stileisten PCIe-Steckplatz...
Page 157
Vorderer Audioanschluss USB 3.0-Stileisten Zusatzlüfteranschluss 2T2R-WLAN-Modul (802.11ac) CPU-Sockel DIMM-Steckplätze Gehäuselüfteranschluss ATX-12-V-Netzanschluss Festplatten sind nicht im Lieferumfang dieses Systems enthalten.
En cas de modifications du présent document, la version mise à jour sera disponible sur le site Internet ASRock sans notification préalable. Si vous avez besoin d’une assistance technique pour ce châssis, veuillez visiter notre site Internet pour plus de détails sur le modèle que vous utilisez.
2 Vue d'ensemble du matériel Ce chapitre comprend des diagrammes illustrant l'emplacement de composants critiques de votre châssis M8. 2.1 Vue avant Description A-Command (bouton OLED tout-en-un) Bouton d'éjection du lecteur optique 4 x ports USB 3.0 Lecteur de cartes 4 en 1 (SD3.0/MMC/MS/MS PRO) Prise microphone Prise casque...
Page 161
2.1.1 Fonction de la A-command La A-command est un bouton multifonction qui permet de sélectionner diverses fonctionnalités. Contrôle de la A-command • Faites tourner le bouton pour sélectionner une fonction principale ou une option. • Appuyez une fois pour confirmer votre choix. Mise en route du système Appuyez sur la A-command pour allumer le système.
Page 162
Arrêt : éteint l'éclairage du châssis Arrêt total : éteint l'éclairage du châssis ; active la fonction Good Night LED *La technologie Good Night LED d'ASRock crée un cadre de sommeil apaisant en éteignant tous les voyants LED non essentiels. En activant la fonction Good Night LED, les LED d'alimentation/disque dur resteront éteints lorsque le...
Page 165
No. Description No. Description Port entrée ligne (témoin bleu) Port eSATA2** Port sortie ligne (citron vert) DisplayPort Port Centre/Caisson de basse (orange) 12 Port HDMI Port sortie haut-parleur arrière (noir) Port USB3.0 Port LAN RJ-45* (Intel Gigabit LAN) Port USB3.0 Ports USB2.0 Port USB3.0 Ports USB2.0...
2.3 Vue interne Description Support de maintien du rehausseur de carte Porte-carte VGA Plateau pour lecteur de disque dur (compatible avec 4 x HDD 2,5" ou 1 x HDD 3,5) Plateau ODD + HDD 2,5" (compatible avec 1 x ODD slot-in et 1 x HDD 2,5") Bloc d'alimentation (450W) Embase du panneau système Connecteurs SATA 3.0...
Page 167
Embases USB 3.0 Connecteurs du ventilateur auxiliaire Module WiFi 2T2R (802.11ac) Socket processeur Sockets DIMM Connecteurs du ventilateur du châssis Connecteur d’alimentation ATX 12V Les disques durs ne sont pas livrés avec ce système.
Congratulazioni per l’acquisto di M8, un sistema barebone di gioco affidabile prodotto secondo i severissimi controlli di qualità ASRock. La scheda madre offre eccellenti prestazioni con un design robusto che si adatta all'impegno di ASRock di offrire sempre qualità e durata.
• Corpo si acciaio / alluminio + plastica Dimensioni • 372 mm (P) x 123 mm (H) x 400 mm (L) Scheda madre • ASRock Z87-M8 • Supporto della famiglia di processori 4 Gen Intel® Core i7 / i5 / i3 / Xeon® / Pentium® / Celeron®...
2 Descrizione del prodotto Questo capitolo fornisce diagrammi che mostrano la posizione dei componenti chiave di M8. 2.1 Veduta frontale Descrizione A-Command (Tasto OLED All-In-One) Tasto d’ e spulsione unità ottica 4 x porte USB 3.0 Lettore di schede 4 in 1 (SD3.0/MMC/MS/MS PRO) Connettore microfono Connettore cuffie...
Page 171
2.1.1 Funzione della manopola A-Command A-Command è una manopola di regolazione polivalente utilizzata per scorrere tra varie funzioni. Controllo della manopola A-Command • Ruotare la manopola per passare tra le principali funzioni od opzioni. • Premere una volta per confermare la selezione. Accensione del sistema Premere la manopola A-Command per accendere il sistema.
Page 172
All off (Disattiva tutto): Disattiva la luce del case; abilita la funzione Good Night LED. *La tecnologia ASRock Good Night LED offre un migliore ambiente per dormire spegnendo i LED non essenziali. Abilitando Good Night LED, i LED alimentazione/HDD si spengono quando il sistema è acceso. La funzione Good Night LED spegne automaticamente i LED alimentazione e della tastiera quando il sistema accede alla modalità...
Page 175
No. Descrizione No. Descrizione Porta ingresso linea (azzurro) Porta eSATA2* Porta uscita linea (verde lime) DisplayPort Porta diffusore centrale/subwoofer Porta HDMI (arancione) Porta uscita diffusori posteriori (nero) 13 Porta USB3.0 Porta LAN RJ-45* (LAN Intel Gigabit) 14 Porta USB3.0 Porte USB2.0 Porta USB3.0 Porte USB2.0 Porta USB3.0...
Page 176
2.3 Veduta interiore Descrizione Staffa di contenimento della scheda riser Supporto scheda VGA Cassetto unità disco rigido (compatibile con 4 x HDD 2,5" o 1 x HDD 3,5") Cassetto ODD + HDD 2,5" (Compatibile con 1 x ODD slot-in e 1 x HDD 2,5") Alimentatore (450W) Header sul pannello del sistema Connettori SATA 3.0...
Page 177
Connettore audio frontale Embases USB 3.0 Connettore ventola ausiliaria Modulo WiFi 2T2R (802.11ac) Socket CPU Prese DIMM Connettore ventola telaio Connettore alimentazione ATX 12V I dischi rigidi non sono inclusi con questo sistema.
Web de ASRock sin previo aviso. Si requiere soporte técnico relacionado con este producto, visite nuestro sitio Web para obtener información específica acerca del modelo que está utilizando. Sitio Web de ASRock: http://www.asrock.com.
Dimensiones • 372 mm (AN) X 123 mm (AL) X 400 mm (LA) Placa base • ASRock Z87-M8 • Admite la familia de procesadores Intel® Core i7 / i5 / i3 / Xeon® / Pentium® / Celeron® de la 4ª generación • Admite DDR3 1600/1333/1066 MHz, 2 ranuras SO-DIMM...
2 Información general del producto En este capítulo se proporcionan diagramas que muestran la ubicación de los componentes importantes de su M8. 2.1 Vista frontal Nº Descripción A-Command (botón OLED todo en uno) Botón de expulsión de la unidad de disco ópticaA-Command (botón OLED todo en uno) 4 puertos USB 3.0 Lector de tarjetas 4 en 1 (SD3.0/MMC/MS/MS PRO)
Page 181
2.1.1 Función de A-Command A-Command es un mando de control multifunción que se utiliza para recorrer varias funciones. Controlar A-Command • Gire el mando para cambiar entre las funciones u opciones principales. • Presione una vez para confirmar la selección. Encender el sistema Presione A-Command para encender la alimentación del sistema.
Page 182
Todo desactivado: Apague la luz de la carcasa; habilite la función Good Night LED. *La tecnología Good Night LED de ASRock mejora el entorno de sueño apagando los LED innecesarios. Al habilitar Good Night LED, los LED de alimentación y de disco duro se apagarán cuando esté encendido. Good Night LED también apagará...
Page 185
Nº Descripción Nº Descripción Puerto de entrada de línea (azul claro) 10 Puerto eSATA2** Puerto de salida de línea (verde lima) DisplayPort Puerto central y para amplificador de Puerto HDMI graves (naranja) Puerto Salida de los altavoces traseros Puerto USB3.0 (negro) Puerto LAN RJ-45* Puerto USB3.0...
2.3 Vista interna Nº Descripción Soporte de retención de la tarjeta vertical (tipo riser) Soporte de la tarjeta VGA Bandeja para unidad de disco duro (compatible con 4 unidades de disco duro de 2,5" o 1 unidad de disco duro de 3,5) Bandeja para unidad de disco óptica + unida de disco duro de 2,5"...
Page 187
Ranura PCI Conector de audio frontal Cabezales USB 3.0 Conector para el ventilador auxiliar Módulo WiFi 2T2R (802.11ac) Zócalo para CPU Zócalos DIMM Conector para el ventilador del chasis Conector de alimentación ATX de 12 V Las unidades de disco duro no se incluyen con este sistema.
Благодарим вас за приобретение надежной игровой базовой системы M8, выпускаемой под постоянным строгим контролем компании ASRock. Система обеспечивает великолепную производительность и характеризуется прочной конструкцией в соответствии с требованиями компании ASRock в отношении качества и долговечности. В случае обновления спецификации на аппаратное обеспечение содержимое настоящей...
Page 189
Цвет • "Черная буря" Материал • Металлический корпус/ алюминий + пластик Размер • 372 мм (Ш) х 123 мм (В) х 400 мм (Д) Материнская • ASRock Z87-M8 плата го ЦП • Поддержка процессоров 4- поколения Intel® Core i7 / i5 / i3 / Xeon® / Pentium® / Celeron®...
2 Обзор изделия В данной главе представлены диаграммы расположения важных компонентов М8. 2.1 Вид спереди № Описание A-Command (Универсальная кнопка ОСИД) Кнопка извлечения оптического диска 4 порта USB 3.0 Устройство чтения карт 4-в-1 (SD3.0/MMC/MS/MS PRO) Разъем для подключения микрофона Разъем для подключения наушников...
2.1.1 Функции A-Command A-Command - это многоцелевая ручка управления, которая используется для выбора различных функций. Управление с помощью кнопки "A-Command" • Поверните ручку для выбора основных функций или параметров. • Нажмите один раз для подтверждения выбора. Включение питания системы Чтобы включить питание системы, нажмите на кнопку "A-Command" Подождите, пока...
Page 192
Выкл.: Выключение подсветки в корпусе Выкл. все: Выключить подсветку в корпусе; активировать функцию Good Night LED *Технология Good Night LED компании ASRock повышает эффективность режима неактивности, отключая ненужные светодиодные индикаторы. Активация технологии Good Night LED позволяет отключить индикаторы питания и жесткого диска при включении питания системы. Функция...
Page 195
№ Описание № Описание Порт линейного входа (голубой) Порт eSATA2** Порт линейного выхода (салатовый) 11 DisplayPort Центральный канал/сабвуфер Порт HDMI (оранжевый) Порт выхода тыловых динамиков Порт USB3.0 (черный) Порт LAN RJ-45* (Intel Gigabit LAN) 14 Порт USB3.0 Порты USB2.0 Порт USB3.0 Порты...
Page 196
2.3 Вид внутри № Описание Скобка для крепления переходной платы Держатель карты VGA Лоток для жесткого диска (совместимый с 4 жесткими дисками 2,5'' или 1 жестким диском 3,5'') Лоток для оптического диска + жесткого диска 2,5'' (совместимый с 1 разъемом для подключения оптического диска и 1 жестким...
Page 197
Гнездо PCIe Аудиоразъем на передней панели Колодки USB 3.0. Разъем дополнительного вентилятора Модуль 2T2R WiFi (802.11ac) Гнездо ЦП Гнезда DIMM Разъем вентилятора корпуса Разъем питания АТХ 12 В Данная система поставляется без жестких дисков.
Caso ocorram modificações a esta docu- mentação, a versão actualizada estará disponível no Web site da ASRock sem aviso prévio. Se necessitar de assistência técnica relacionada com este produto, visite o nosso Website para obter informações específicas acerca do modelo que está...
• Corpo em aço / Alumínio + Plástico Dimensões • 372 mm (L) x 123 mm (A) x 400 mm (C) Placa principal • ASRock Z87-M8 • Suporta processadores Intel® Core i7 / i5 / i3 / Xeon® / ª...
2 Descrição geral do produto Este capítulo apresenta diagramas que mostram a localização dos componentes do sistema M8. 2.1 Vista frontal N.º Descrição A-Command (Botão OLED tudo em um) Botão de ejecção do disco óptico 4 x portas USB 3.0 Leitor de cartões 4-em-1 (SD3.0/MMC/MS/MS PRO) Tomada para microfone Tomada para auscultadores...
Page 201
2.1.1 A função do A-Command O A-Command é um botão controlador multifunções que é utilizado para percorrer as diversas funções. Controlar o A-Command • Rode o o botão para alternar entre as funções principais ou opções. • Prima uma vez para confirmar a sua selecção. Ligar o sistema Prima o botão A-Command para ligar o sistema.
Page 202
Desligar tudo: Desligar a luz da caixa; activar a função de LED de Boa Noite *A tecnologia LED de Boa Noite da ASRock proporciona-lhe um melhor ambiente de sono desligando os LEDs não essenciais. Ao activar a função LED de Boa Noite, os LEDs de Energia/HDD serão desligados quando o sistema estiver...
Page 203
2.2 Vista posterior N.º Descrição Tampas de ranhura PCIe Painel de E/S Conector de alimentação AC...
Page 205
N.º Descrição N.º Descrição Porta entrada de linha (azul claro) Porta eSATA2** Porta de saída de linha (verde claro) DisplayPort Porta de Subwoofer/Centro (laranja) Porta HDMI Porta de saída do altifalante traseiro Porta USB3.0 (preto) Porta LAN RJ-45* (Intel Gigabit LAN) 14 Porta USB3.0 Portas USB 2.0 Porta USB3.0...
Page 206
2.3 Vista interna N.º Descrição Suporte de retenção da placa Suporte da placa VGA Compartimento da unidade de disco rígido (compatível com 4 x HDD de 2,5" ou 1 x HDD de 3,5") Compartimento de ODD + HDD de 2,5" HDD (compatível com 1 x ODD de entrada de ranhura e 1 x HDD de 2,5") Fonte de alimentação (450W) Terminal do painel de sistema...
Page 207
Conector de áudio do painel frontal Terminais USB 3,0 Conector da ventoinha auxiliar Módulo WiFi 2T2R (802.11ac) CPU socket Este sistema não inclui os discos rígidos.
Page 208
하드웨어을 업데이트할 수도 있기 때문에 , 이 문서의 내용은 예고 없이 변경될 수 있 습니다 . 이 설명서가 변경될 경우 , 업데이트된 버전은 ASRock 의 웹사이트에서 추가 통지 없이 제공됩니다 . 이 제품과 관련하여 기술적 지원이 필요한 경우 , 당사의 웹사...
Page 209
• 강철 본체 / 알루미늄 + 플라스틱 재질 • 372mm (W) x 123mm (H) x 400mm (L) 치수 • ASRock Z87-M8 마더보드 • 4 세대 Intel® Core i7 / i5 / i3 / Xeon® / Pentium® / Celeron® 프로세서 제품군 지원...
Page 210
2 제품 개요 이 장에서는 M8 의 중요 구성부품의 위치를 보여주는 다이어그램을 제공합니 다 . 2.1 앞면 번호 설명 A-Command ( 올인원 OLED 버튼 ) 광학 디스크 드라이브 꺼내기 버튼 USB 3.0 포트 4 개 4-in-1 카드 리더 (SD3.0/MMC/MS/MS PRO) 마이크...
Page 211
2.1.1 A-Command 의 기능 A-Command 는 여러 기능 사이에서 전환하는 데 사용되는 다목적 컨트롤러 스 위치입니다 . A-Command 조절 • 스위치를 돌려 주요 기능 또는 옵션 사이에서 전환합니다 . • 한 번 누르면 선택이 확인됩니다 . 시스템 켜기 A-Command 를 눌러 시스템 전원을 켭니다 . 운영체제가 자동으로 로드할 때까 지...
Page 212
꺼짐 : 케이스의 라이트를 끕니다 모두 꺼짐 : 케이스의 라이트를 끄고 Good Night LED 기능을 활성화합니다 . *ASRock Good Night LED 기술은 불필요한 LED 를 꺼서 더욱 편안하게 잠 을 잘 수 있는 환경을 제공합니다 . Good Night LED 를 활성화하면 , 시스템...
Page 213
2.2 뒷면 번호 설명 PCIe 슬롯 커버 I/O 패널 AC 입력 전원 커넥터...
Page 215
번호 설명 번호 설명 라인 입력 포트 ( 담청색 ) eSATA2 포트 ** 라인 출력 포트 ( 라임색 ) DisplayPort 센터 / 서브우퍼 포트 ( 주황색 ) HDMI 포트 후면 스피커 출력 포트 ( 검정 ) USB3.0 포트 LAN RJ-45 포트 * (Intel Gigabit LAN) 14 USB3.0 포트...
Page 216
2.3 내부 번호 설명 라이저 카드 고정 브래킷 VGA 카드 홀더 하드 디스크 드라이브 트레이 (2.5" HDD 4 개 또는 3.5" HDD 1 개와 호환 ) ODD + 2.5" HDD 트레이 ( 슬롯 삽입식 ODD 1 개와 2.5" HDD 1 개와 호환 ) 전원공급장치...
Page 217
USB 3.0 헤더 보조 팬 커넥터 2T2R WiFi 모듈 (802.11ac) CPU 소켓 DIMM 소켓 섀시 팬 커넥터 ATX 12V 전원 커넥터 하드 드라이브는 별도로 구입하셔야 합니다 .
Page 221
2.1.1 A-command の機能 A-command は、 さまざまな機能を切り替える際に使用する多目的コントローラノ ブです。 A-command を制御する ノブを回転してメイン機能またはオプションを切り替えます。 • 1 回押して選択を確定します。 • システムの電源をオンにします。 A-command を押してシステムの電源をオンにします。 オペレーティ ングシステム が自動的に読み込まれるまでお待ちく ださい。 システムの電源をオフにします。 OLED に M8 Logo / Date and Time ( M8 ロゴ / 日付と時刻) が表示されたら、 A-command を押し、 「 Yes (はい) 」 を選択してシステムの電源をオフにします。 Windows を開く前に...
Page 222
O(オフ) : ケース内のライ トをオフにします All o(すべてオフ) : ケース内のライ トをオフにして、 Good Night LED (グッ ド ナイ ト LED) 機能を有効にします *ASRock の Good Night LED (グッ ドナイ ト LED) テク ノロジーは不必要な LED を消灯して、 スリープ状態の環境を改善します。 Good Night LED (グッ ドナイ ト LED) 機能を有効にした場合は、 システムの電源を入れると、 電源...