Professional Calibration Eq Graphical Output; Display; Remote Control; Hdmi - Pioneer VSX-922-K Operating Instructions Manual

13

Professional Calibration EQ graphical output

Symptom Remedy
The reverb characteristics graph There are cases where the graph does not appear flat (even when selecting ALL CH ADJ
after EQ calibration does not appear in the Auto MCACC Setup) due to adjustments made to compensate for room character-
entirely flat. istics to achieve optimal sound.
Areas of the graph may appear identical (before and after) when there is little or no
adjustment needed.
The graph may appear to have shifted vertically when comparing before and after mea-
surements.
EQ adjustments made using the Despite level adjustments being made, the filters used for analysis may not display these
Manual MCACC setup do not appear adjustments in the reverb characteristics graph after EQ calibration. However, these
to change the reverb characteristics adjustments are taken into account by the filters dedicated to overall system calibration.
graph after EQ calibration.
Lower frequency response curves do Low frequencies used in bass management (the subwoofer channel) will not change for
not seem to have been calibrated for speakers that have been specified as SMALL in the configuration, or do not output these
SMALL speakers. frequencies.
Calibration is performed, but due to your speakers' low frequency limitations, no measur-
able sound is output for display.

Display

Symptom Remedy
The display is dark or off. Press DIMMER repeatedly to select a different brightness.
The OSD screen is not displayed. The OSD screen is not displayed unless the receiver and TV are connected using an
HDMI cable. If the TV does not support HDMI, perform the various operations and make
the settings while watching the display on the receiver's front panel.
You can't get DIGITAL to display Check the digital connections and make sure that the digital inputs are assigned cor-
when using SIGNAL SEL. rectly (see The Input Setup menu
2 DIGITAL or DTS does not light These indicators do not light if playback is paused.
when playing Dolby/DTS software.
Check the playback (especially the digital output) settings of the source component.
When playing Dolby Digital or DTS Check that the player is connected using a digital connection.
sources, the receiver's format indica-
Make sure that the receiver is set to AUTO or DIGITAL (see
tors do not light.
page 45).
Check that the player isn't set up so that Dolby Digital and DTS sources are converted to
PCM.
Ensure that if there are several audio tracks on the disc, the Dolby Digital or DTS is
selected.
When playing certain discs, none of The disc may not contain 5.1/6.1 channel material. Check the disc packaging for more on
the receiver's format indicators light. what audio tracks are recorded on the disc.
When playing a disc with the listen- Make sure that the receiver is set to AUTO or DIGITAL (see
ing mode set to Auto Surround or page 45).
ALC, 2 Pro Logic II or DTS Neo:6
If a two channel soundtrack is currently playing (including Dolby Surround encoded),
appear on the receiver.
then this is not a malfunction. Check the disc packaging for details about the audio
tracks available.
During playback of DVD-Audio, the This will occur when playing DVD-Audio material over the HDMI connection. This is not a
display shows PCM. malfunction.
on page 34).
Choosing the input signal on
Choosing the input signal on
Symptom Remedy
The power turns off automatically See the Power section
and some indicator flashes, or some
indicator flashes and the power does
not turn on.
Chinese cannot be selected for the FONT must be switched to Chinese at the OSD character set setting. For details, see
OSD Language setting. Selecting the OSD character set
Track names, etc., are not displayed The OSD Language setting must be switched to Chinese after switching FONT to
in Chinese on the OSD when playing Chinese at the OSD character set setting. For details, see
with the network function, a USB set on page 7
input, etc.

Remote control

Symptom Remedy
Cannot be remote controlled. Set the remote control unit's remote control mode so that it matches the setting on the
main unit (see
Check whether the receiver's remote control mode is properly set (see
Mode Setup
Try replacing the batteries in the remote control (see
Be sure to operate within 7 m and a 30º angle of the remote sensor on the front panel (see
Operating range of remote control unit
Check that there are no obstacles between the receiver and the remote control.
Make sure that there is no fluorescent or other strong light shining on to the remote
sensor.
Other components can't be operated If the battery ran down, the preset codes may have been cleared. Re-enter the preset
with the system remote. codes.
The preset code may be incorrect. Redo the procedure for entering preset codes.
When commands from the remote control units of other devices are registered using the
learning function, in some cases they may not be learned properly. In this case, register
the commands again using the learning function (see
they may be in a special format that cannot be registered on this receiver's remote con-
trol. Operate the device using another remote control.

HDMI

Symptom Remedy
The HDMI indicator blinks continu- Check all the points below.
ously.
88
(page 85).
on page 7.
Selecting the OSD character
and Changing the OSD display language (OSD Language)
Operating multiple receivers on page 64).
on page 82).
Loading the batteries
on page 7).
page 65). If they still do not work,
FAQ
on page 32.

Remote Control

on page 7).