Switching The Speaker Terminals; Using The Multi-Zone Controls - Pioneer VSX-922-K Operating Instructions Manual

09

Switching the speaker terminals

If you selected Normal(SB/FH), Normal(SB/FW) or Speaker B at
switch between speakers using the SPEAKERS button. If you selected Front Bi-Amp or ZONE 2, the button will
simply switch your main speaker terminals on or off.
1 Press to the receiver operation mode.
2 Use SPEAKERS to select a speaker system setting.
As mentioned above, if you have selected Front Bi-Amp or ZONE 2, the button will simply switch your main
speaker terminal (A) on or off.
Press repeatedly to choose a speaker terminal option:
When you select Normal(SB/FH), you can select from:
! SP: SB/FH ON – Surround back or front height channels are added to the front, center and surround chan-
nels (maximum 5 channels) and a maximum of 7 channels are output. The surround back and front height
channels are switched automatically according to the audio input signal.
! SP: SB ON – Surround back channels are added to the front, center and surround channels (maximum 5
channels) and a maximum of 7 channels are output.
! SP: FH ON – Front height channels are added to the front, center and surround channels (maximum 5 chan-
nels) and a maximum of 7 channels are output.
! SP: OFF – No sound is output from the speakers.
When you select Normal(SB/FW), you can select from:
! SP: SB/FW ON – Surround back or front wide channels are added to the front, center and surround channels
(maximum 5 channels) and a maximum of 7 channels are output. The surround back and front wide channels
are switched automatically according to the audio input signal.
! SP: SB ON – Surround back channels are added to the front, center and surround channels (maximum 5
channels) and a maximum of 7 channels are output.
! SP: FW ON – Front wide channels are added to the front, center and surround channels (maximum 5 chan-
nels) and a maximum of 7 channels are output.
! SP: OFF – No sound is output from the speakers.
When you select Speaker B, you can select from:
! SP: A ON – Sound is output from the A-speaker terminals (up to 7 channels (including surround back chan-
nels), depending on the source).
! SP: B ON – Sound is output from the two speakers connected to the B-speaker terminals. Multichannel
sources will not be heard.
! SP: A+B ON – Sound is output from the A-speaker terminals (up to 5 channels, depending on the source), the
two speakers connected to the B-speaker terminals, and the subwoofer. The sound from the B-speaker termi-
nals will be the same as the sound from the A-speaker terminals (multichannel sources will be downmixed to
2 channels).
! SP: OFF – No sound is output from the speakers.
Note
! The subwoofer output depends on the settings you made in
B ON is selected above, no sound is heard from the subwoofer (the LFE channel is not downmixed).
! All speaker systems (except Speaker B connections) are switched off when headphones are connected.
Speaker system setting on page 78, you can
Manual speaker setup on page 78. However, if SP:

Using the MULTI-ZONE controls

The following steps use the front panel controls to adjust the sub zone volume and select sources. See
ZONE remote controls on page 60.
1 Press MULTI-ZONE ON/OFF on the front panel.
Each press selects a MULTI-ZONE option:
! ZONE 2 ON – Switches the MULTI-ZONE feature on
! MULTI ZONE OFF – Switches the MULTI-ZONE feature off
The MULTI-ZONE indicator lights when the MULTI-ZONE control has been switched ON.
2 Press MULTI-ZONE CONTROL on the front panel.
! When the receiver is on, make sure that any operations for the sub zone are done while ZONE 2 shows in the
display. If this is not showing, the front panel controls affect the main zone only.
3 Use the INPUT SELECTOR dial to select the source for the sub zone.
For example, ZONE 2 DVD sends the source connected to the DVD inputs to the sub room (ZONE 2).
! If you select TUNER, you can use the tuner controls to select a preset station (see
on page 40 if you're unsure how to do this). The tuner cannot be tuned to more than one station at a time.
Therefore, changing the station in one zone also changes the station in the other zone. Please be careful not
to change stations when recording a radio broadcast.
4 When Speaker System is set to ZONE 2, use the MASTER VOLUME dial to adjust the volume
for the sub zone.
5 When you're finished, press MULTI-ZONE CONTROL again to return to the main zone
controls.
You can also press MULTI-ZONE ON/OFF on the front panel to switch off all output to the sub zone.
! You won't be able to switch the main zone off completely unless you've switched off the MULTI-ZONE control
first.
! If you don't plan to use the MULTI-ZONE feature for a while, turn off the power in both the sub and main
rooms so that this receiver is in standby.
MULTI-ZONE remote controls
Press the remote control's ZONE 2 to operate the ZONE 2.
The following table shows the possible MULTI-ZONE remote controls:
Button(s) What it does
Switches on/off power in the sub zone.
u
INPUT SELECT Use to select the input function in the sub zone.
Use to select the input function directly (this may not work for some functions) in the sub
Input function buttons
zone.
VOLUME +/–
Use to set the listening volume in the sub zone.
<a>
MUTE Mutes the sound or restores the sound if it has been muted (adjusting the volume also
<a> restores the sound).
a In case of VSX-1122
The volume cannot be adjusted on the receiver if Volume Level at ZONE 2 Setup under ZONE Setup is set to –40 dB Fixed or
0 dB Fixed.
In case of VSX-922
You can only use this button when Speaker System is set to ZONE 2.
60
Using other functions
MULTI-
Saving station presets