Table of Contents
Advertisement
13
Settings
Symptom
Remedy
The Auto MCACC Setup continually
The ambient noise level may be too high. Keep the noise level in the room as low as pos-
shows an error.
sible (see also
Problems when using the Auto MCACC Setup
level cannot be kept low enough, you will have to set up the surround sound manually
(page 89
).
When using only one surround back speaker, connect it to the SURROUND BACK L
(Single) terminals.
To use a 5.1-channel speaker set, use the surround speakers for the surround channel,
not the surround back channel.
Make sure there are no obstacles between the speakers and the microphone.
If Reverse Phase is displayed, try the following:
— The speaker's wiring (+ and –) may be inverted. Check the speaker connections.
— Depending on the type of speakers and their installation conditions, Reverse Phase
may be displayed even if the speakers are properly connected. If this happens, select
GO NEXT and continue.
— If the speaker is not pointed to the microphone (listening position) or when using
speakers that affect the phase (dipole speakers, reflective speakers, etc.), it may not be
possible to properly identify the polarity.
After using the Auto MCACC Setup,
There may have been some low frequency noise in the room from an air-conditioner,
the speaker size setting is incorrect.
motor, etc. Switch off all other appliances in the room and use Auto MCACC Setup again.
Depending on a number of factors (bass reproduction capabilities of the speakers, room
size, speaker placement, etc.) this may occur in some cases. Change the speaker setting
manually in
Speaker Setting
the Auto MCACC menu in
problem.
Can't adjust the Fine Speaker Dis-
Check that the speakers are all in phase (make sure the positive (+) and negative (–)
tance setting properly.
terminals are matched up properly).
The display shows KEY LOCK ON
With the receiver in standby, press u STANDBY/ON for about 5 seconds while holding
when you try to make settings.
down SPEAKERS to disable the key lock.
Most recent settings have been
The power cord was disconnected from the wall while adjusting this setting.
erased.
Settings are only stored if all the zones are turned off. Turn off all the zones before
unplugging the power cord.
The various system settings are not
Do not pull out the power cord while conducting the settings. (The settings will be stored
stored.
when both the main zone and sub zone turn off. Turn off all zones before pulling out the
power cord.)
Certain listening modes or
When Operation Mode is set to Basic, the Pioneer-recommended settings are made and
HOME MENU items cannot be
not all of the functions can be used. To use all of the functions without restrictions, set
selected.
Operation Mode to Expert (see
Feels like there is no subwoofer EQ
The effect becomes less when the set frequency value of the crossover frequency is low.
effect.
When setting a high frequency value, the subwoofer EQ effect becomes stronger. How-
ever, setting a higher crossover frequency increases the share that the subwoofer bears
for low-frequency playback. For that reason, it is disadvantageous in terms of the phase
point of view. Set to your preference.
on
page 38
). If the noise
on
page 89
, and use the ALL (Keep SP System) option for
Automatic MCACC (Expert)
on
page 82
if this is a recurring
Operation Mode Setup
on
page 40
).
Professional Calibration EQ graphical output
Symptom
Remedy
The reverb characteristics graph
There are cases where the graph does not appear flat (even when selecting ALL CH ADJ
after EQ calibration does not appear
in the Auto MCACC Setup) due to adjustments made to compensate for room character-
entirely flat.
istics to achieve optimal sound.
Areas of the graph may appear identical (before and after) when there is little or no
adjustment needed.
The graph may appear to have shifted vertically when comparing before and after mea-
surements.
EQ adjustments made using the
Despite level adjustments being made, the filters used for analysis may not display these
Manual MCACC setup do not appear
adjustments in the reverb characteristics graph after EQ calibration. However, these
to change the reverb characteristics
adjustments are taken into account by the filters dedicated to overall system calibration.
graph after EQ calibration.
Lower frequency response curves do
Low frequencies used in bass management (the subwoofer channel) will not change for
not seem to have been calibrated for
speakers that have been specified as SMALL in the configuration, or do not output these
SMALL speakers.
frequencies.
Calibration is performed, but due to your speakers' low frequency limitations, no measur-
able sound is output for display.
Display
Symptom
Remedy
The display is dark or off.
Press DIMMER repeatedly to select a different brightness.
The OSD screen is not displayed.
The on-screen display is not displayed unless the receiver's HDMI OUT 1 terminal and
the TV are connected with an HDMI cable. If the TV does not support HDMI, perform the
operations and make the settings watching the display on the receiver's front panel.
When the input is a 3D signal, OSD cannot be displayed.
Even through the input is switched,
Check the digital connections and make sure that the digital inputs are assigned cor-
DIGITAL does not light.
rectly (see
These indicators do not light if playback is paused.
DIGITAL or DTS does not light
when playing Dolby/DTS software.
Make sure that the receiver is set to AUTO or DIGITAL (see
page 54
).
Check the playback (especially the digital output) settings of the source component.
When playing Dolby Digital or DTS
Check that the player is connected using a digital connection.
sources, the receiver's format indica-
Make sure that the receiver is set to AUTO or DIGITAL (see
tors do not light.
page 54
).
Check that the player isn't set up so that Dolby Digital and DTS sources are converted to
PCM.
Ensure that if there are several audio tracks on the disc, the Dolby Digital or DTS is
selected.
When playing certain discs, none of
The disc may not contain multi-channel material. Check the disc packaging for more on
the receiver's format indicators light.
what audio tracks are recorded on the disc.
It does not light when the PCM signal or analog signal is input.
101
The Input Setup menu
on
page 39
).
Choosing the input signal
Choosing the input signal
FAQ
on
on
- Quick Links:
- Resetting the System
Hide quick links:
Advertisement
Chapters
Table of Contents
