After Sales Service - Dimplex CDE2TI Cadiz Eco Owner's Manual

Table of Contents

Advertisement

Manual Operation
Pressing ' ' from the default HIGH screen (Fig. 7) brings the heater
into AUTO mode - see 'Setting the Timer Programs'. Press again to put
the heater into OFF mode - see Fig. 5. Press again for left hand side
heat (
appears on LCD display - see Fig. 6). Press again for right
hand side heat (
appears on LCD display). Press again brings the
user full circle to FULL heat mode (
Setting the Desired Temperature
The desired temperature can be set using the ' ' or '
temperature can be set from 5
display. When the temperature is reached the heater will automatically
switch OFF. If the ambient temperature drops the heater will come on
again automatically. Note the electronic climate control device conserves
energy and assists with temperature regulation e.g. if the heater is set
to HIGH heat and the temperature is set to 28
will switch to a lower heat setting. Then at 28
off
completely.
Setting the Timer Programs
Two program settings are possible, P1 and P2. Only high heat is possible
for program settings. Press ' ' once to set the programs, starting with
P1 AUTO ON – See Fig 10.
1.
The hour digit will flash. To adjust the hour use the ' ' & ' ' buttons.
Confirm the hour digit by pressing '
2.
The minute digit will flash. To adjust the minute use the ' ' & ' '
buttons. Confirm the hour digit by pressing '
3.
Now P1 AUTO OFF is displayed, P1 off time can now be set. Repeat
steps 1 & 2 to set P1 off time.
At this point either:
(a) Press ' ' to exit the Program mode and return to AUTO mode.
The heater is now in AUTO mode. The heater will switch ON and
OFF depending on programme P1 previously entered.
OR
(b) Repeat steps 1 - 3 as above to set the programme for P2.
At this point press ENTER or PROG to exit the Programme mode.
The heater is now in AUTO mode. The heater will switch ON and
OFF depending on programme P1 & P2 previously entered. If after
programming and returning to the AUTO mode display, P1 or P2 is
active, the display will show PROG 1 AUTO ON or PROG 2 AUTO ON
depending on which is active - see Fig. 10. An OFF time cannot be
entered which is less than the corresponding ON time. When setting the
timer programs if no keys are pressed, the display will (after 4 minutes)
revert to the previous display i.e. display prior to entering Program mode.
Run Programs
If MODE is pressed until AUTO appears on the screen (either AUTO-
ON or AUTO-OFF), the heater will run both P1 and P2 program as they
are set.
NOTE: The heater cannot be programmed to run P1 only or P2 only.
To cancel P1, set P1 OFF time to be same as P1 ON time. To cancel P2
set P2 OFF time to be same as P2 ON time.
Review Program settings
To review the program settings the heater must be in AUTO mode. Press
ENTER and the times for PROG 1 ON, PROG 1 OFF, PROG 2 ON and
PROG 2 OFF will be displayed consecutively for 2 seconds. The display
will automatically return to the state it was in before ENTER was pressed.
FROST Protection Mode
With the heater in any mode, OFF, MANUAL ON or AUTO, if the
displayed set temperature is reduced to 5
FROST Protection mode - see Fig. 11. In this mode only, if the ambient
temperature drops below 5
C, will the heater come on. This is to prevent
o
freezing. In FROST Protection mode the heater comes on in the high
heat mode only. Pressing the ' ' button is the only way to bring the
heater out of this special mode.
Remote Control Operation - see Fig. 13
(CDE2ECC(B) & CDE24ECC(B) models only)
The batteries for the remote control are not installed in the remote but
are packed separately in the carton. To install batteries please follow
diagrams behind battery cover on the remote control.
The remote allows the set temperature to be adjusted, the mode to be
selected or can be used to put the heater in FROST Protection mode.
Full Heat output can only be achieved when using the remote control
i.e. both Left hand and Right hand panels are on.
appears on LCD display).
' keys. The
C to 35
C and this will be shown on the
o
o
C, at 27
C the heater
o
o
C the heater will switch
o
'.
'.
C the heater will go into
o
Press the ' ' button on the Remote Control to go from OFF, Man On
High and back to OFF again. Press the ' ' or '
to set desired temperature between 5
to put the heater into FROST Protection mode. Pressing the ' ' button
(on the Remote Control) is the only way (using the Remote Control) to
bring the heater out of this mode i.e. pressing the ' ' or '
the remote will have no effect on the heater.
Discard leaking batteries
Dispose of batteries in the proper manner according to Provincial and
local regulations. Any battery may leak electrolyte if mixed with a different
battery type, if inserted incorrectly, if all the batteries are not replaced at
the same time, if disposed of in a fire or if an attempt is made to charge
a battery not intended to be recharged.
Storage
If the radiator is not required for long periods, for example during the
summer, it should be stored in a dry place and preferably covered to
prevent the accumulation of dirt and dust. The plug and cord can be
stored in the storage area provided – see Fig. 14. The cord should be
neatly coiled around the hooks provided and the plug inserted into the
pin-hole in the central compartment.
Safety Overheat Protection
For your safety this appliance is fitted with a thermal cut-out. In the
event that the product overheats for some reason, the cut-out prevents
excessive temperatures on the product by cutting the power to the
heater. Once the heater has cooled down, it will reset automatically,
it will continue to cycle on and off automatically until the reason for
overheating is removed.
Cleaning
WARNING - ALWAYS DISCONNECT THE POWER SUPPLY BEFORE
CLEANING THE HEATER.
Do not use detergents, abrasive cleaning powder or polish of any kind
on the body of the heater.
Allow the heater to cool, then wipe with a dry cloth to remove dust
and a damp cloth (not wet) to clean off stains. Be careful not to allow
moisture in to the heater.

After Sales Service

Please see the separate Warranty leaflet for details of your Warranty &
after sales service including contact details.
Should you require after sales service, please get in touch with the
supplier through whom you purchased the appliance, or the contract
number on your Warranty leaflet.
' buttons on the remote
C and 35
C. Press the '
' button
o
o
' buttons on

Hide quick links:

Advertisement

Table of Contents
loading

This manual is also suitable for:

Cde2tib cadiz ecoCde2ecc cadiz ecoCde2eccb cadiz ecoCde24ecc cadiz ecoCde24eccb cadiz eco

Table of Contents