Sharp XE-A21S Programming Manual page 17

[JOB#145] Graphic logo data loading
The below data is loaded. Files are set in the folder for "LOGO Data".
File Name
1 Graphic LOGO LOGO
(*1) The contents of each file are same as the communication data of
"ONLINE FUNCTION". Details of "File No." and "Table No." are
described in "ONLINE SPECIFICATION". All data are converted to
use at "Customer Support Tool" software on PC.
Note: Files are created only for the "Customer Support Tool" software
on PC. Any users dose not need to concern its contents.
■ DISPLAY AND PRINT:
Key
1 2 3 4 5 6 7 8 9 0
[STBL] P
141 P
[@/FOR] P
[SBTL] P
[1] P
[CA/AT] S d - A C C E S S .
(SD ACCESS) S d - A C C E S S .
Case of NORMAL END
Case of ERROR END E - S d - 0 1
Cas e of CHANGING
MODE KEY
(to cancel)
Case of POWER OFF E - S d - P. O F F
File/Table
Field (*1)
No. (*1)
E0
Display
123456789012345678901234
1 4 1
1 4 1
-
(PRE-PRINT HEADDER)
! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! !
YOU SELECT SD CARD JOB
PUSH [1]-KEY to EXECUTE
PUSH [CL]-KEY to CANCEL
! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! !
Don't turn the mode key
! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! !
1
05/02/2006 12:34PM
123456#1234
*PGM*
#141
0. 0 0
***NORMAL END
(Issuing Receipt)
SD ERROR
(Issuing Receipt)
0. 0 0
SD CANCELED
(Issuing Receipt)
POWER OFF ERROR
AT THE DEVICE CONTROL
SET DATA&TIME AGAIN
(Issuing Receipt)
XE-A21S PROGRAM MODE
[JOB#144] All Data Saving
[JOB#148] All Data Loading
Notes: • In case of "DATA SAVING", the message of confirmation for
overwritten the file on SD Card does not display. Data is over-
written if there is data of the same file name.
• In case of "DATA LOADING", the condition of ECR will return
to past condition. However, the message of confirmation for
overwritten does not display.
The below data is saved or loaded. Files are set in the folder for "ALL
RAM BACKUP".
1 All RAM data
Note: Each files are used only for the purpose of DATA BACKUP at
ECR. Any users dose not need to concern its contents.
Print
while executing a job.
(Issuing Receipt)
HEADER
01
BETTY___
01
2 – 14
File Name
All
NOTE
The buffered keys are cleared and the message is
printed on "receipt" only.
(It is not print on "journal" and "EJ".)
MESSAGE : MAX 8-lines
(The message is fixed in ROM.)
(Not count up CC# at this time.)
(Count up CC#.)
DISPLAY : "." is blinking while executing job.
PRINT : JOB HEADDER is printed.
And job code is printed.
(Job code is printed only at SD jobs)
DISPLAY: "." is blinking while executing job. PRINT
PRINT : (NON)
DISPLAY: (INITIAL)
PRINT : STATUS is printed
(The message is fixed in ROM.)
DISPLAY: ERROR CODE (2-digits)
PRINT : SD ERROR MESSAGE and ERROR
CODE
(The message is fixed in ROM.)
DISPLAY: (INITIAL)
PRINT : SD CANCEL MESSAGE
(The message is fixed in ROM.)
DISPLAY: ERROR MESSAGE
PRINT : MESSAGE of POWER OFF
(The message is fixed in ROM.)