General; Getting Started; Step 1 : Unpacking; Step 2 : Setting Up The Remote Commander - Sony SLV-LX500 Service Manual

QQ
3 7 63 1515 0

1. GENERAL

Getting Started

Step 1 : Unpacking

Check that you have received the following items with the VCR:
• Remote commander
• Size AA (R6) batteries
• Plug adaptor (SLV-LX700S CS only)
If the plug supplied with your VCR does not fit
your power outlet, attach the supplied adaptor
to the plug.
Check your model name
The instructions in this manual are for the 4 models: SLV-LX700S MX/CS, SLV-LX600S
MX and SLV-LX500 MX. Check your model name by looking at the rear panel of your
VCR.
SLV-LX700S MX is the model used for illustration purposes. Any difference in operation
is clearly indicated in the text, for example, "SLV-LX700S MX only."
TE
L 13942296513
4
Unpacking
Controlling other TVs with the remote commander
(not available on SLV-LX500)
The remote commander is preprogramed to control non-Sony TVs. If your TV is
listed in the following table, set the appropriate manufacturer's code number.
1 Set •TV / VIDEO at the top of the remote commander to •TV.
Hold down ?/1, and enter your TV's code number using the number buttons.
2
Then release ?/1.
Now you can use the ?/1, VOL (volumen) +/–, CH (canal) +/–, and TV/VIDEO
buttons to control your TV. You can also use the buttons marked with a dot (•) to
control a Sony TV. To control the VCR, reset •TV / VIDEO to VIDEO.
Code numbers of controllable TVs
If more than one code number is listed, try entering them one at a time until you find
the one that works with your TV.
TV brand
Sony
Akai
AOC
Centurion
Coronado
Curtis-Mathes
Daytron
Emerson
Fisher
General Electric
Gold Star
Hitachi
J.C.Penney
www
JVC
KMC
Magnavox
Marantz
MGA/Mitsubishi
.
NEC
6
Setting up the remote commander
http://www.xiaoyu163.com
• 75-ohm coaxial cable with F-type connectors
• Audio/video cable (3-phono to 3-phono)
(SLV-LX700S and SLV-LX600S only)
Code number TV brand Code number
01 Panasonic 06, 19
04 Philco 03, 04
04 Philips 08
12 Pioneer 16
03 Portland 03
12 Quasar 06, 18
12 Radio Shack 05, 14
03, 04, 14 RCA 04, 10
11 Sampo 12
06, 10 Sanyo 11
03, 04, 17 Scott 12
02, 03 Sears 07, 10, 11
04, 12 Sharp 03, 05, 18
09 Sylvania 08, 12
03 Teknika 03, 08, 14
x ao u163
03, 08, 12 Toshiba 07
y
04, 13 Wards 03, 04, 12
04, 12, 13, 17 Yorx 12
i
04, 12 Zenith 15
http://www.xiaoyu163.com
2 9
8

Step 2 : Setting up the remote commander

Inserting the batteries
Insert two size AA (R6) batteries
by matching the + and – on the
batteries to the diagram inside the
battery compartment.
Insert the negative (–) end first,
then push in and down until the
positive (+) end clicks into
position.
Using the remote
commander
You can use this remote
commander to operate this VCR
and a Sony TV. Buttons on the
remote commander marked with a
dot (•) can be used to operate your
Sony TV.
If the TV does not have the
symbol near the remote sensor, this
remote commander will not
operate the TV.
To operate
the VCR
a Sony TV
Notes
• With normal use, the batteries should last about three to six months.
• If you do not use the remote commander for an extended period of time, remove the batteries
to avoid possible damage from battery leakage.
• Do not use a new battery with an old one.
Q Q
3 6 7 1 3 • Do not use different types of batteries. 1 5
Notes
• If you enter a new code number, the code number previously entered will be erased.
• If the TV uses a different remote control system from the one programed to work with the
VCR, you cannot control your TV with the remote commander.
• When you replace the batteries of the remote commander, the code number may change. Set
the appropriate code number every time you replace the batteries.
• When you press the AUDIO MONITOR (monitor de audio) button, your TV's menu may
appear on the TV screen. To exit the TV menu, press the MENU button on the TV remote
commander or wait until the menu disappears automatically.
co
.
1-1
SLV-LX500/LX600S/LX700S
9 4 2 8
This section is extracted from instruction manual.
(3-081-607-E1)
Remote sensor
•TV / VIDEO
1 2 3
4 5 6
Set •TV / VIDEO to
VIDEO and point at the remote sensor at the VCR
•TV and point at the remote sensor at the TV
0 5 8 2 9 9 4 2 8
Setting up the remote commander
m
Setting up the remote commander
9 9
9 9
continued
5
7