Table of Contents
Advertisement
QQ
3 7 63 1515 0
Editing with another VCR
How to connect to record on this VCR
For SLV-LX700S and SLV-LX600S
This VCR (Recorder)
LINE-2 IN (entrada de línea 2)
Audio/video cable (not supplied)
: Signal flow
For SLV-LX500
This VCR (Recorder)
LINE-2 IN (entrada de línea 2)
Audio/video cable (not supplied)
: Signal flow
TE
L 13942296513
48
Editing with another VCR
Additional Information
Antenna information
Attaching the external antenna connector
When using a 300-ohm twin lead cable for a
VHF/UHF antenna, use an antenna connector
(not supplied) to connect the antenna to the
VCR.
1
Loosen the screws on the antenna connector.
2
Wind the twin leads around the screws on the antenna connector.
3
Retighten the screws.
Attaching a UHF/VHF band mixer
When using both a 75-ohm coaxial cable and
a 300-ohm twin lead cable for a VHF/UHF
antenna, use a UHF/VHF band separator/
mixer (not supplied) to connect the antenna
to the VCR.
1
Loosen the screws on the mixer.
2
Wind the twin leads around the screws on the mixer.
www
3
Retighten the screws.
4
Connect the 75-ohm coaxial cable to the mixer.
.
50
Antenna information
http://www.xiaoyu163.com
TV
Other VCR (Player)
LINE OUT
(salida de línea)
TV
Other VCR (Player)
LINE OUT
(salida de línea)
300-ohm twin
lead cable
Antenna
connector (not
supplied)
300-ohm twin
lead cable
UHF/VHF
Band
separator/
mixer (not
supplied)
75-ohm coaxial
cable
x
ao
u163
y
i
http://www.xiaoyu163.com
2 9
8
Notes
• Make sure you connect the plugs to jacks of the same color.
• If the other VCR is a monaural type and connected to this VCR's LINE-2 IN (entrada de línea
2) jacks, connect the audio plug to the AUDIO L (audio izquierda) (white) jack. The sound is
recorded on both right and left channels. If you connect to the AUDIO R (audio derecha)
(red) jack, the sound is recorded only on the right channel (SLV-LX700S and SLV-LX600S
only).
• If you connected this VCR to both the LINE IN (entrada de línea) and LINE OUT (salida de
línea) jacks of the other VCR, select the input correctly to prevent a humming noise.
• You can use the LINE IN 1 (entrada de línea 1) jacks for editing.
• If the other VCR is a monaural type and connected to this VCR's LINE IN 1 (entrada de línea
1) jacks, the sound is recorded only on the channel whose jack is connected to the audio plug.
To record on both right and left channels, connect the audio plugs to the AUDIO R/L (audio
derecha/izquierda) jacks using an audio/video cable (not supplied) (SLV-LX700S and SLV-
LX600S only).
Operation (when recording on this VCR)
Before you start editing
• Turn on the VCR and the TV and set
it to the video channel.
• Press INPUT SELECT (selección de
entrada) or CHANNEL (canal) +/– to
display "L1" or "L2" in the display
window.
• Press SP/EP to select the tape speed,
SP or EP.
1
Insert a source tape with its safety tab removed into the other (playback) VCR.
Search for the point to start playback and set it to playback pause.
2
Insert a tape into this (recording) VCR. Search for the point to start recording
and press X PAUSE (pausa).
Press z REC (grabación) on this VCR to set it to recording pause.
3
To start editing, press the X PAUSE (pausa) buttons on both VCRs at the same
4
time.
To stop editing
Press the x STOP (parada) buttons on both VCRs.
Tip
• To cut out unwanted scenes while editing, press X PAUSE (pausa) on this VCR when an
unwanted scene begins. When it ends, press X PAUSE (pausa) again to resume recording.
Q Q
3
6 7
1 3
Troubleshooting
If you have any questions or problems not covered below, please consult your nearest Sony
dealer.
Symptom
The ?/1 switch does not function.
The power is turned on but the VCR
does not operate.
The clock has stopped and "– –:– –"
appears in the display window.
The playback picture does not appear
on the TV screen.
The picture is not clear.
The picture rolls vertically during
picture search.
The picture has no sound.
A TV program does not appear on
the TV screen.
TV reception is poor.
The tape starts playing as soon as it is
inserted.
The tape is ejected when you press
z REC (grabación).
Nothing happens when you press
z REC (grabación).
.
1-12
9 4
2 8
X PAUSE (pausa)
z REC (grabación)
1 5
0 5
8
2 9
9 4
Editing with another VCR
Remedy
• Connect the AC power cord securely.
• Make sure the VCR is not locked. To unlock, hold down
?/1 POWER (alimentación) on the VCR until "LOC"
disappears.
• Moisture condensation has occurred. Turn the power off,
unplug the AC power cord and leave the VCR to dry for
over three hours.
• The clock stops if the VCR is disconnected from the wall
outlet for more than one minute. Reset the clock (and
timer).
• Make sure the TV is set to the channel for the VCR. If
you are using a monitor, set it to video input.
• Adjust the tracking with the TRACKING
(seguimiento) +/– buttons.
• The video heads are dirty (see the last page of
"Troubleshooting"). Clean the video heads using a
Sony's video head cleaning cassette. If a Sony cleaning
cassette is not available in your area, have the heads
cleaned at your nearest Sony dealer (a standard service
fee will be charged). Do not use a commercially available
liquid type cleaning cassette, as it may damage the video
heads.
• The video heads may have to be replaced. Consult your
local Sony dealer for more information.
• Adjust the vertical hold control on the TV or monitor.
• The tape is defective.
• If you made A/V connections, check the audio cable
connection.
• Make sure the TV is set to the channel for the VCR. If
you are using a monitor, set it to video input.
• Select the correct source with the INPUT SELECT
(selección de entrada) or CH (canal) +/– buttons. Select a
channel number when recording TV programs; select
"L1" or "L2" when recording from other equipment.
m
• Adjust the TV antenna.
• The safety tab has been removed. To record on this tape,
cover the tab hole.
co
• Check that the safety tab has not been removed.
• Make sure the tape is not at its end.
continued
Troubleshooting
9 9
2 8
9 9
49
51
Advertisement
Table of Contents
