Table of Contents
Advertisement
Quick Links
SERVICE MANUAL
1
2
4
5
7
8
0
Refer to the SERVICE MANUAL of VHS MECHANICAL
ADJUSTMENT
for MECHANICAL ADJUSTMENTS.
(9-921-748-11)
System
Format
VHS NTSC standard
Video recording system
Rotary head helical scanning FM system
Video heads
Double azimuth four heads
Video signal
NTSC color, EIA standards
Tape speed
3
SP: 33.35 mm/s (1
/
inches/s)
8
EP: 11.11 mm/s (
7
/
inches/s)
16
LP: 16.67 mm/s (
11
/
inches/s),
16
playback only
Maximum recording/playback time
9 hrs. in EP mode (with T-180 tape)
Fast-forward and rewind time
Approx. 3 min. (with T-120 tape)
Tuner section
Channel coverage
VHF 2 to 13
UHF 14 to 69
CATV A-8 to A-1, A to W, W+1 to W+84
Antenna
75-ohm antenna terminal for VHF/UHF
Input and outputs
LINE-1 IN and -2 IN
VIDEO IN, phono jack (1 each)
Input signal: 1 Vp-p, 75 ohms, unbalanced, sync
negative
AUDIO IN, phono jacks (2 each)
Input level: 327 mVrms
Input impedance: more than 47 kilohms
3
6
9
SPECIFICATIONS
LINE OUT
VIDEO OUT, phono jack (1)
Output signal: 1 Vp-p, 75 ohms, unbalanced,
sync negative
AUDIO OUT, phono jacks (2)
Standard output: 327 mVrms
Load impedance: 47 kilohms
Output impedance: less than 10 kilohms
Timer section
Clock
Quartz locked
Timer indication
12-hour cycle
Timer setting
8 programs (max.)
Power back-up
Built-in self-charging capacitor
Back-up duration: up to 1 hour at a time
General
Power requirements
110 V AC to 240 V AC, 50/60 Hz
(SLV-LX80S CS)
120 V AC, 60 Hz
(SLV-LX80S MX)
SLV-LX80S
Power consumption
Operating temperature
Storage temperature
Dimensions
Mass
Supplied accessories
Remote commander (1)
Size AA (R6) batteries (2)
75-ohm coaxial cable with F-type connectors (1)
Audio/video cable (1) (3-phono to 3-phono)
Plug adaptor (1) (SLV-LX80S CS only)
Design and specifications are subject to change
without notice
ENERGY STAR
As an ENERGY STAR
has determined that this product meets the
ENERGY STAR
VIDEO CASSETTE RECORDER
— 1 —
RMT-V294A
Chilean Model
Mexican Model
S MECHANISM
17W
5°C to 40°C (41°F to 104°F)
-20°C to 60°C (-4°F to 140°F)
Approx. 430 97 292 mm (w/h/d)
(Approx. 17 3 11 inches) including
projecting parts and controls
Approx. 4.1 kg (9 lb 1 oz)
®
is a U.S. registered mark.
®
Partner, Sony Corporation
®
Advertisement
Table of Contents
Related Manuals for Sony SLV-LX80S
Summary of Contents for Sony SLV-LX80S
-
Page 1: Specifications
Fast-forward and rewind time Built-in self-charging capacitor Audio/video cable (1) (3-phono to 3-phono) Approx. 3 min. (with T-120 tape) Plug adaptor (1) (SLV-LX80S CS only) Back-up duration: up to 1 hour at a time Tuner section Design and specifications are subject to change... - Page 2 COMPONENTS IDENTIFIED BY MARK ! OR DOTTED LINE WITH MARK ! ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
-
Page 3: Table Of Contents
TABLE OF CONTENTS Section Title Page Section Title Page SERVICE NOTE • MA-397 (6/7)(DISPLAY CONTROL) SCHEMATIC DIAGRAM ......4-17 ERROR CODE INDICATION ........... 5 • MA-397 (7/7)(POWER SUPPLY) SCHEMATIC DIAGRAM ......4-19 GENERAL • FJ-28 (LINE-2 IN) Getting Started ................1-1 PRINTED WIRING BOARD AND Step 2 : Setting up the remote commander ...... -
Page 4: Service Note
SERVICE NOTE 1. ERROR CODE INDICATION • Error codes are indicated using the lower 5 digits in the fluorescent display tube. “At this time, Colon “:” between character is not indicated.” Mode code indication when the error has occurred. Error code ERROR CODE 0 No error 1 Cam encoder error Loading direction... -
Page 5: General
Now you can use the ?/1, VOL +/–, CH +/–, and TV/VIDEO buttons to control your TV. You can also use the buttons marked with a dot (•) to control a Sony TV. To Insert the negative (–) end first, control the VCR, reset •TV / VIDEO to VIDEO. -
Page 6: Step 3 : Hookups
Completing A/V hookup Hookup 1 After you’ve connected your TV and completed antenna or cable hookup, return to this procedure to complete VCR set up. This will prevent unwanted noise in the RF Antenna hookup channel. Make the following connections if you’re using an antenna (if you don’t have cable TV). - Page 7 VCR. “ACS” (Auto Clock Set) will flash in the display window and search for a AUTO time signal provided by Sony Entertainment Television (SETV). After that, MANUAL whenever you turn off the VCR, it checks the time and adjusts the clock, even for Daylight Saving Time.
-
Page 8: Selecting A Language
VCR. “ACS” (Auto Clock Set) will flash in the display window and search for a PREAJUSTE DEL SINTONIZADOR AJUSTE DEL RELOJ time signal provided by Sony Entertainment Television (SETV). After that, SELECCION DEL IDIOMA VOLVER whenever you turn off the VCR, it checks the time and adjusts the clock, even for Daylight Saving Time. - Page 9 If the clock does not activate Press M/m to highlight NO for TOTAL. AJUSTE AUTOMATICO RELOJ AUTO. and press OK. PLAY TOTAL. AUTO. CH AJUSTE RELOJ – – – HORARIO VERANO AUTO VOLVER SELECCIONAR AJUSTAR PARA SALIR MENU Press M/m to highlight the item you want to set and press OK.
-
Page 10: Presetting Channels
Press M/m to highlight ANTENA/CABLE, then press OK. Presetting channels PLAY This VCR is capable of receiving VHF channels 2 to 13, UHF channels 14 to 69 and unscrambled CATV channels 1 to 125. First, • To preset cable TV channels: we recommend that you preset the receivable PREAJUSTE DEL SINTONIZADOR Press M/m to set ANTENA/CABLE to... -
Page 11: Basic Operations
If the picture is not clear Press M/m to highlight PREAJUSTE DEL PREAJUSTE DEL SINTONIZADOR Normally, the Auto Fine Tuning (AFT) SINTONIZADOR, then press OK. PLAY ANTENA / CABLE CABLE function automatically tunes in channels AJUSTE AUTO. clearly. If, however, the picture of a channel MANUAL is not clear, you can also use the manual SINTONIA FINA... -
Page 12: Recording Tv Programs
When the tape reaches the end, it will rewind automatically. PLAY You can only use this function if your TV is made by Sony (Trinitron TV). How to connect to use this function Connect the VCR and TV with the audio/video cable (see “Audio/video (A/V) Additional tasks hookup”... -
Page 13: Recording Tv Programs Using The Dial Timer
To watch another TV program while recording Recording TV programs using the Dial Press TV/VIDEO to turn off the VIDEO indicator in the display window. Timer If the TV is connected to the VCR’s LINE OUT jacks, set the TV to the TV’s antenna input;... -
Page 14: Recording Tv Programs Using The Timer
To set the clock About the Demonstration Mode The Dial Timer function has a Demonstration Mode that allows the user, such as a Turn DIAL TIMER so that “RELOJ” appears in the display window. salesperson, to enter more than eight examples of timer settings when demonstrating the use of the Dial Timer. -
Page 15: Additional Operations
Additional Operations To use the VCR after setting the timer Playing/searching at various speeds To use the VCR before timer recording begins, just press ?/1. The indicator disappears from the display window and the VCR switches on. Remember to press ?/1 to reset the VCR to the timer recording standby mode after using the VCR. -
Page 16: Synchronized Recording
Press INPUT SELECT or CH +/– to display “L1” in the display window. Synchronized Recording Set the timer on the connected equipment to the time of the program you want to record, then turn it off. You can set the VCR to automatically record programs from equipment such as a Press SP/EP to select the tape speed. -
Page 17: Recording Stereo And Bilingual Programs
How sound is recorded on a video tape Recording stereo and bilingual programs The VCR records sound onto two separate tracks. Hi-fi audio is recorded onto the main track along with the picture. Monaural sound is recorded onto the normal audio track along the edge of the tape. -
Page 18: Searching Using The Time Search Function
Searching using the Time Search function Skip-searching automatically (Quick View) You can easily find a specific point on a tape You can spot check an entire tape quickly SEARCH MODE by using the Time Search function. using the Quick View function. At intervals, For example, you can find a recorded portion the VCR skips playback while searching 15 minutes ahead of or behind the current... -
Page 19: Adjusting The Picture
About the Adaptive Picture Control (APC) function Adjusting the picture The Adaptive Picture Control (APC) function automatically improves recording and playback quality by adjusting the VCR to the condition of the video heads and tape. To maintain better picture quality, we recommend that you set APC to SI on Adjusting the tracking PÁGINA2 of the OPCIONES menu (The APC indicator lights up in the display Although the VCR automatically adjusts the tracking... -
Page 20: Editing With Another Vcr
Operation (when recording on this VCR) Editing with another VCR Before you start editing X PAUSE • Turn on your TV and set it to the video channel. How to connect to record on this VCR • Press INPUT SELECT or CHANNEL +/–... -
Page 21: Index To Parts And Controls
Display window Index to parts and controls Refer to the pages indicated in parentheses ( ) for details. Front panel STEREO VIDEO APC SAP LP SP A Timer indicator (40) (44) F APC (Adaptive Picture Control) indicator (62) B SAP (Second Audio Program) indicator G RR (Reality Regenerator) indicator (61) (53) C STEREO indicator (53) - Page 22 K ?/1 (power) switch (6) (44) L TV/VIDEO button (6) (37) M AUDIO MONITOR button (53) N TIMER button (43) (51) O Number buttons (37) P ENTER button (37) Q CH (channel) +/– buttons (6) (36) R CLEAR button (33) (52) S y SLOW button (46) T ×2 button (46) U REPLAY button (33)
-
Page 23: Disassembly
SLV-LX80S SECTION 2 DISASSEMBLY NOTE: Follow the disassembly procedure in the numerical order given. 2-1. CASE, FRONT PANEL BLOCK ASSEMBLY 1 Two tapping screws 3 Upper case 5 Flat Cable FDI-002 2 Two tapping screws Hooks 6 Flat Cable FDM-010... -
Page 24: Rear Panel
2-3. REAR PANEL 2 Rear panel (Engaged by the seven hooks) Hooks Hooks Hooks 1 POWER code stopper 2-4. MA-397 BOARD 1 Six screws (Sumitite (B3) +BV) 2 MA-397 board with mechanism deck... -
Page 25: Mechanism Deck
2-5. MECHANISM DECK 4 Flat cable 3 Flat Cable 5 Connector 6 Two screws (BVTP 3 × 12) 9 Screw 2 Screw (BVTP 3 × 12) (Sumitite (B3), +BV) qs Mechanism deck 1 Flexible cable (CN260) CN101 CN351 CN350 CN600 qa MA-397 board 0 MD base (R) 7 MD base (M) -
Page 26: Internal Views
2-6. INTERNAL VIEWS — Top View — M901 ACE head block assembly Drum Assembly A-6759-620-A DZH-0B7A-R 1-772-366-11 Pinch press block assembly A-6759-863-B FE head 1-500-144-11 Reel (T) table Reel (S) table FL complete assembly 3-977-508-01 3-977-507-01 A-6775-359-C — Bottom View — M902 DC motor (capstan) 1-698-971-11... -
Page 27: Circuit Boards Location
2-7. CIRCUIT BOARDS LOCATION MA-397 VIDEO, AUDIO, SERVO/SYSTEM CONTROL, TUNER, POWER SUPPLY FJ-28 (LINE 2 IN) DM-98 (USER CONTROL) DI-81 (DIAL TIMER) 2-5E... -
Page 28: Block Diagrams
SLV-LX80S SECTION 3 BLOCK DIAGRAMS 3-1. OVERALL BLOCK DIAGRAM... -
Page 29: Video Block Diagram
SLV-LX80S 3-2. VIDEO BLOCK DIAGRAM IC160 OSD V OUT REC IC160 OSD V OUT PB IC201 IC201 IC201 C VIDEO IN IC160 2.2Vp-p REC/PB 2.3Vp-p 2.0Vp-p 1.0Vp-p 2.3Vp-p 2.1Vp-p IC160 OSC V IN REC IC160 OSC V IN PB IC201... -
Page 30: Servo/System Control Block Diagram
SLV-LX80S 3-3. SERVO/SYSTEM CONTROL BLOCK DIAGRAM... -
Page 31: Tuner Block Diagram
SLV-LX80S 3-4. TUNER BLOCK DIAGRAM... -
Page 32: Audio Block Diagram
SLV-LX80S 3-5. AUDIO BLOCK DIAGRAM MA-397 BOARD (SEE PAGE 4-13) TU701 T380 50Vp-p 69.9kHz 3-10... -
Page 33: Power Block Diagram
SLV-LX80S 3-6. POWER BLOCK DIAGRAM CHILEAN MEXICAN 3-11 3-12E... -
Page 34: Printed Wiring Boards And Schematic Diagrams
SLV-LX80S SECTION 4 PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this, the necessary note is printed in each block.) (For printed wiring boards) • : Pattern from the side which enables seeing. -
Page 35: Frame Schematic Diagram
SLV-LX80S 4-1. FRAME SCHEMATIC DIAGRAM FRAME SCHEMATIC DIAGRAM... -
Page 36: Printed Wiring Boards And Schematic Diagrams
SLV-LX80S 4-2. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS MA-397 (VIDEO, AUDIO, SERVO/SYSTEM CONTROL, TUNER, POWER) PRINTED WIRING BOARD There are few cases that the part printed on this diagram isn’t mounted in this model. — Ref. No. MA-397 Board:1,000 Series —... - Page 37 SLV-LX80S MA-397 (REC/PB HEAD AMP) SCHEMATIC DIAGRAM – Ref. No: MA-397 Board; 1000 series – • See page 4-21 for waveforms CN270 MA-397 BOARD(1/7) NO MARK:REC/PB MODE JL271 HF ADJ R :REC MODE REC/PB HEAD AMP(RP BLOCK) JL272 PB RF...
- Page 38 SLV-LX80S MA-397 (Y/C, AUDIO PROCESS) SCHEMATIC DIAGRAM • See page 4-5 for printed wiring board. • See page 4-21 for waveforms. MA-397 BOARD(2/7) •REF.NO.:1000 SERIES- NO MARK:REC/PB MODE R :REC MODE XX MARK:NO MOUNT Y/C,AUDIO PROCESSOR(VA BLOCK) P :PB MODE...
- Page 39 SLV-LX80S MA-397 (SERVO/SYSTEM CONTROL) SCHEMATIC DIAGRAM • See page 4-5 for printed wiring board. • See page 4-22 for waveforms. MA-397 BOARD(3/7) •REF.NO.:1000 SERIES- NO MARK:REC/PB MODE XX MARK:NO MOUNT R :REC MODE SERVO/SYSTEM CONTROL(SS BLOCK) P :PB MODE OSD_VCC...
-
Page 40: 2/7)(Y/C, Audio Process)
SLV-LX80S MA-397 (AUDIO PROCESS) SCHEMATIC DIAGRAM • See page 4-5 for printed wiring board. MA-397 BOARD(4/7) AUDIO PRO0CESS(AU BLOCK) •REF.NO.:1000 SERIES- XX MARK:NO MOUNT NO MARK:REC/PB MODE JL331 R :REC MODE MA-397(5/7) (SEE PAGE 4-15) P :PB MODE JL325 MPX_MODE... - Page 41 SLV-LX80S MA-397 (TUNER) SCHEMATIC DIAGRAM • See page 4-5 for printed wiring board. MA-397 BOARD(5/7) TUNER(TU BLOCK) •REF.NO.:1000 SERIES- XX MARK:NO MOUNT TU701 10 11 12 13 14 15 16 17 18 22 23 24 JL718 R704 C701 R703 JL715...
-
Page 42: 6/7)(Display Control)
SLV-LX80S MA-397 (DISPLAY CONTROL) SCHEMATIC DIAGRAM • See page 4-5 for printed wiring board. MA-397 BOARD(6/7) DISPLAY CONTROL(FRONT BLOCK) •REF.NO.:1000 SERIES- XX MARK:NO MOUNT R420 R429 R430 R419 2700 NO MARK:REC/PB MODE JL433 JL434 JL435 S424 S422 S421 AN_GND CN403... -
Page 43: 7/7)(Power Supply)
SLV-LX80S MA-397 (POWER SUPPLY) SCHEMATIC DIAGRAM • See page 4-5 for printed wiring board. MA-397 BOARD(7/7) POWER SUPPLY(PS BLOCK) •REF.NO.:1000 SERIES- XX MARK:NO MOUNT NO MARK:REC/PB MODE Q600 L660 TO TU 68uH 2SB1398-Q(TA).S0 JL618 MTR 12V REG +30V 13.5 SW_5V... - Page 44 SLV-LX80S MA-397 MA-397 MA-397 BOARD (1/7) BOARD (2/7) BOARD (3/7) (R/P BLOCK) (VA BLOCK) (SS BLOCK) 4fsc (OUT) IC260 4 REC/PB IC201 2 REC IC201 yj REC/PB IC160 el IC160 i;T REEL REC/PB 4.8Vp-p 1.6sec (TAPE TOP) 3.6Vp-p 380mVp-p 3.579545MHz R 460mVp-p 14.31818MHz...
-
Page 45: Line-2 In
SLV-LX80S FJ-28 (LINE 2 IN) PRINTED WIRING BOARD AND SCHEMATIC DIAGRAM — Ref. No. FJ-28 Board:2,000 Series — FJ-28 BOARD There are few cases that the part printed on this diagram isn’t mounted in this model. FJ-28 BOARD R801 LINE 2 IN CN801 •REF.NO.:2000 SERIES-... - Page 46 SLV-LX80S DM-98 (USER CONTROL) PRINTED WIRING BOARD AND SCHEMATIC DIAGRAM — Ref. No. DM-98 Board:2,000 Series — DM-98 BOARD There are few cases that the part printed on this diagram isn’t mounted in this model. DM-98 BOARD USER CONTROL •REF.NO.:2000 SERIES-...
- Page 47 SLV-LX80S DI-81 (DIAL TIMER) PRINTED WIRING BOARD AND SCHEMATIC DIAGRAM — Ref. No. DI-81 Board:1,000 Series — DI-81 BOARD There are few cases that the part printed on this diagram isn’t mounted in this model. MA-397 VIDEO, AUDIO, SERVO/SYSTEM CONTROL,...
-
Page 48: Interface, Ic Pin Function Description
SLV-LX80S SECTION 5 INTERFACE, IC PIN FUNCTION DESCRIPTION 5-1. SYSTEM CONTROL — MECHANISM BLOCK INTERFACE (MA-397 BOARD IC160) CASSETTE CASSETTE TAPE TAPE STOP EJECTED Signal Pin No. LOARDING UNLOARDING THREADING UNTEREADING MA-397 Board IC160ed MA-397 Board MODE 1 — —... -
Page 49: System Control - System Control Peripheral Circuit Interface (Ma-397 Board Ic160)
5-3. SYSTEM CONTROL — SYSTEM CONTROL PERIPHERAL CIRCUIT INTERFACE (MA-397 BOARD IC160) Signal Pin No. I/O level MA-397 Board RESET Normally “H”, “L” when service interruption detected or restored. IC160ef MA-397 Board I2C DATA 1 Serial communication data to EEPROM I2C161. IC160es MA-397 Board I2C CLOCK 1... -
Page 50: Servo/System Control Microprocessor Pin Functions (Ma-397 Board Ic160)
5-7. SERVO/SYSTEM CONTROL MICROPROCESSOR PIN FUNCTIONS (MA-397 BOARD IC160) Pin No. Pin Name Function DEST Destination control input FULL ERS STEREO/MONO/SAP DETECTION TU AFT Tuner analog AFT input FUNC KEY2 Key input FUNC KEY1 Key input S SENS Tape end sensor input T SENS Tape top sensor input V RF ENV... - Page 51 Pin No. Pin Name Function WHITE LEVEL White level signal input OSD V OUT OSD Video signal output OSD Vcc — SW 5V (OSD block) External low-pass filter for slicer/AFC is connected to this terminal V HOLD External capacitor for slicer is connected to this terminal C VIDEO IN Control video signal input (osd, tuner, sorvo) —...
-
Page 52: Adjustments
SLV-LX80S SECTION 6 ADJUSTMENTS 2-1-3. Set-up of Adjustment MECHANICAL ADJUSTMENTS In this adjustment, NTSC pattern generator is connected with LINE input terminal. When check to tuner, connected AERIAL terminal. For the mechanical adjustments, please refer to the Check that the synchronizing signal of the Y signal has an amplitude “VHS MECHANICAL ADJUSTMENT MANUAL... -
Page 53: Input/Output Levels And Impedance
2-1-5. Input/Output Levels and Impedance 2-2. POWER SUPPLY CHECK Video input: LINE IN 2-2-1. Output Voltage Check (MA-397 Board) Input signal: 1 Vp-p, 75 ohms, unbalanced, Mode STANDBY sync negative +30 V Check Video output: LINE OUT Measurement point C671 3 Output signal: 1 Vp-p, 75 ohms, unbalanced, Specified value 31.0 to 39.0 V... -
Page 54: Servo System Check
2-3. SERVO SYSTEM CHECK 2-4. AUDIO SYSTEM ADJUSTMENT 2-3-1. RF Switching Position Adjustment • Adjust both L ch and R ch. (MA-397 Board) [Connecting Instruments] [Adjustment Purpose] Audio line OUTPUT L/R To adjust the link of the A-ch and B-ch of the tape playback outputs. To make the unit compatible with other tapes and units. -
Page 55: Hifi Switching Position Adjustment (Ma-397 Board)
2-4-2. HiFi Switching Position Adjustment 2-4-5. Audio Noise Check (MA-397 Board) [Adjustment purpose] [Adjustment Purpose] Confirm that the noise level is within the specification. To adjust the link of the A-ch and B-ch of the tape playback outputs. Mode REC and PB (SP mode) To make the unit compatible with other tapes and units. -
Page 56: Adjusting Parts Location Diagram
SLV-LX80S 2-5. ADJUSTING PARTS LOCATION DIAGRAM MA-397 BOARD (CONDUCTOR SIDE) CNJ561 CN270 VIDEO/AUDIO LINE RF/HF SWP IN/OUT C671 +30 V Q600 MTR12 V -11V +12V Q674 D420 SW5V JS401 IC660 ND420 6-5E... -
Page 57: Repair Parts List
4-921-277-41 SCREW (B2.6 x 8), TAPPING, BIND * 11 3-057-168-41 CASE, UPPER A-6794-718-A DM-98 MOUNT 3-710-901-61 SCREW, TAPPING 1-757-552-12 FLAT CABLE FDM-010 * 13 1-418-698-11 COMMANDER, STANDARD (RMT-V294A) A-6794-730-A DI-81 MOUNT 3-943-995-31 EMBLEM (NO.5), SONY 1-757-553-11 FLAT CABLE FDI-002 3-057-165-01 PLATE,EARTH... -
Page 58: Chassis Section
SLV-LX80S 7-1-2. CHASSIS SECTION Not Supplied Not Supplied Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks 3-959-383-01 BASE (R), MD 3-970-608-21 SUMITITE (B3), + BV X-3950-107-1 PANEL ASSY, REAR 1-757-550-11 FLAT CABLE FMD-021 * 53 A-6713-822-A MA-397 COMPLETE (Chilean) -
Page 59: Mechanism Deck Section-1
SLV-LX80S 7-1-3. MECHANISM DECK SECTION-1 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks 3-977-509-01 WASHER, THRUST 3-063-773-02 OPENER, LID (SL) 3-977-507-01 TABLE, REEL (S) 3-977-441-03 GEAR, PINCH PRESSING 3-977-508-01 TABLE, REEL (T) 3-977-445-02 GEAR, TG8 ARM DRIVING... -
Page 60: Mechanism Deck Section-2
SLV-LX80S 7-1-4. MECHANISM DECK SECTION-2 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks X-3947-581-4 BRAKE ASSY,MAIN(T) 3-965-178-01 SPRING 3-977-462-01 SPRING,EXTENTION. (MAIN BRAKE) 3-062-687-01 BASE DRUM, K (UPPER MOTOR) X-3947-573-1 ARM ASSY, PENDULUM A-6750-328-E SHUTTLE (T) BLOCK ASSY... -
Page 61: Mechanism Deck Section-3
SLV-LX80S 7-1-5. MECHANISM DECK SECTION-3 M902 M903 supplied Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks 3-977-437-01 RETAINER, CAM MOTOR 3-063-755-01 GEAR, CAM X-3947-584-1 ASSY, REEL DIRECT 3-977-442-03 SLIDER 3-977-443-01 WASHER, STOPPER 3-063-757-01 GEAR, LOADING(T) 3-063-760-01 WORM - WHEEL... -
Page 62: Electrical Parts List
SLV-LX80S DI-81 DM-98 FJ-28 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks 7-2. ELECTRICAL PARTS LIST NOTE: • Due to standardization, replacements in the • RESISTORS When indicating parts by reference number, All resistors are in ohms. - Page 63 SLV-LX80S MA-397 FJ-28 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R803 1-216-022-00 RES-CHIP 1/10W C176 1-164-004-11 CERAMIC CHIP 0.1µF R804 1-216-013-00 RES-CHIP 1/10W C185 1-109-982-11 CERAMIC CHIP 1µF C187 1-164-346-11 CERAMIC CHIP 1µF C188 1-109-982-11 CERAMIC CHIP 1µF...
- Page 64 SLV-LX80S MA-397 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks C271 1-164-232-11 CERAMIC CHIP 0.01µF C350 1-126-160-11 ELECT 1µF C272 1-164-004-11 CERAMIC CHIP 0.1µF C351 1-104-664-11 ELECT 47µF C275 1-164-232-11 CERAMIC CHIP 0.01µF C352 1-163-038-00 CERAMIC CHIP 0.1µF...
- Page 65 SLV-LX80S MA-397 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks ! C602 1-113-900-11 CERAMIC 470PF 250V CN404 1-766-980-71 CONNECTOR, FFC/FPC 7P ! C603 1-113-900-11 CERAMIC 470PF 250V CN600 *1-580-230-11 PIN, CONNECTOR (PC BOARD) 2P ! C604...
- Page 66 SLV-LX80S MA-397 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks IC260 8-759-564-36 IC LA70011 JR118 1-216-296-00 SHORT IC301 8-759-696-39 IC AN3668FBP JR119 1-216-296-00 SHORT IC350 8-759-499-30 IC BA7755AF-E2 JR120 1-216-296-00 SHORT IC404 8-759-643-83 IC UPD16315GB-3BS JR121...
- Page 67 SLV-LX80S MA-397 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks L303 1-414-857-51 INDUCTOR 100µH <RESISTOR> L380 1-414-857-51 INDUCTOR 100µH L420 1-414-185-51 INDUCTOR 22µH R101 1-249-413-11 CARBON 1/4W R102 1-216-077-91 RES-CHIP 1/10W L500 1-414-930-21 INDUCTOR 2.2µH R103...
- Page 68 SLV-LX80S MA-397 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R205 1-208-830-11 METAL CHIP 100K 0.5% 1/10W R380 1-216-017-91 RES-CHIP 1/10W R208 1-216-295-00 SHORT R381 1-216-063-91 RES-CHIP 3.9K 1/10W R209 1-216-067-00 RES-CHIP 5.6K 1/10W R382 1-217-671-11 RES-CHIP...
- Page 69 SLV-LX80S MA-397 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R621 1-249-429-11 CARBON 1/4W <CRYSTAL> R622 1-216-430-11 METAL OXIDE R623 1-247-843-11 CARBON 3.3K 1/4W X160 1-767-857-11 VIBRATOR, CRYSTAL 14.31818 MHz ! R640 1-219-153-11 FUSIBLE 1/4W X161 1-579-463-11 VIBRATOR, CRYSTAL 32.469 KHz...
- Page 70 SLV-LX80S SLV-LX80S Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks 20001A0800-1 Sony Corporation 2001. 1 NETWORK ENTERTAINMENT GROUP 9-921-785-11 Published by Quality Assurance Dept. – 86 – 7-14...