Entering Letters/Characters; Specifications; Questions And Answers - Gigaset A400 User Manual

Changing the pause after line seizure
You can set the length of the pause inserted between
pressing the accept key
phone number.
P#Q5#1O
Menu ¤
the current pause length flashes: 1 = 1 sec.; 2 = 3 sec.;
3 = 7 sec. ¤
Enter number
Changing the pause after recall key
P#Q5#14
Menu ¤
current pause length flashes
3 = 3200 ms ¤
Enter number
Appendix

Entering letters/characters

Press the relevant key the number of times indicated.
Briefly press the hash key
"123" mode, from "123" to "abc" mode and from "abc"
to "Abc" mode.
Standard characters
1x 2x 3x 4x 5x 6x 7x 8x 9x 10 11 12 13 14 15
1 1 £ $ ¥ ¤
2 a b c 2 ä á à â ã ç
I d e f 3 ë é è ê
4 g h i 4 ï
í
5 j k l 5
L m n o 6 ö ñ ó ò ô õ
M p q r s 7 ß
N t u v 8 ü ú ù û
O w x y z 9 ÿ ý æ ø å
Q
1)
. , ? ! 0 + -
P
* / ( ) < = > %
#
Abc
123 # @ \ & §
--> -->
abc
123
1) Space

Specifications

Recommended batteries
Technology: Nickel-metal-hydride (NiMH)
Size: AAA (Micro, HR03)
Voltage: 1.2 V
Capacity: 400–800 mAh
The device is supplied with two approved batteries.
Base power consumption
In standby mode
- Charged handset in base
- Handset not in base
During a call
c
and transmitting the
¤ The number for
¤ OK.
¤ The number for the
: 1 = 800 ms; 2 = 1600 ms;
¤ OK
.
#
to switch from "Abc" to
ì î
: ¿ ¡ " '
approx. 0.7 W
< 0.4 W
approx. 0.5 W
13
General specifications
DECT standard
GAP standard
Range
Base power supply
Environmental condi-
tions in operation
Standby time
Talktime
Operating time for 1.5
hours of calls per day
- Without Eco Mode+
- With Eco Mode+
Charging time in
charger

Questions and answers

If you have any queries about the use of your tele-
phone, visit our website at
www.gigaset.com/service
for assistance 24/7. The table below contains a list of
common problems and possible solutions.
Problem
Nothing
appears in the
display.
No wireless
connection to
the base, Base
flashes in the
; _
display.
You cannot
hear a ringer
melody/dial-
ling tone from
the fixed line
network.
Error tone
sounds after
system PIN
prompt.
PIN forgotten.
The connec-
tion always
terminates
after approx.
30 seconds.
Is supported
Is supported
(The Gigaset handset is only fully
functional on Gigaset bases)
Up to 300 m outdoors
Up to 50 m indoors
230 V ~/50 Hz
+5°C to +45°C, 20% to 75% relative
humidity
220 hours
20 hours
135 hours
90 hours
5.5 hours
Cause Solution
a
The handset is not Press the end call key
switched on. for approx.
5 seconds or place the
handset in the base.
The batteries are Charge or replace the
flat. batteries.
The handset is out- Move the handset
side the range of closer to the base.
the base.
The handset is not Register the handset
¢ page 11.
registered.
The base is not Check the mains con-
switched on. nector on the base
¢ page 3.
The phone cord Please always use the
supplied has not phone cord supplied or
been used or has ensure that the pin
been replaced by a connections are cor-
new cord with the rect when purchasing
wrong pin connec- from a retailer: 3-4
tions. assignment of tele-
phone leads/EURO
CTR37.
You have entered Reset the system PIN to
the wrong system the default setting
0000 ¢ page 12.
PIN.
All handsets are de-
registered. All settings
are reset. All lists are
deleted.
Repeater acti- Deactivate and
vated/deactivated reactivate the handset
¢ page 12. ¢ page 6.