Setting The Alarm Clock; Phone Settings; Repeater Mode; Changing The Display Language - Gigaset A400 User Manual

Internal listening in (conference)
You want to listen in to an existing external call.
c
Press and hold the key. You can listen in to the call.
All participants hear a signal tone.
To end: press the end call key
a signal tone.
If the first internal participant presses the end call key
a
, the handset that has "listened in" remains con-
nected to the external participant.

Setting the alarm clock

Activating/deactivating the alarm clock
Menu ¤ Alarm Clock ¤ OK ¤ Activation
‰
¤ OK (
= activated)
If activated:
¤ Enter wake-up time ¤ OK
When the alarm clock rings, press any key to switch it
off for 24 hours. If the alarm clock is set, the wake-up
icon l will appear on the screen and the wake-up
time will be displayed instead of the date.
Entering/changing the wake-up time
Menu ¤ Alarm Clock ¤ OK ¤ Wakeup time ¤ OK
Enter the wake-up time in hours and minutes, then
press . The alarm clock is automatically activated
OK
after the wake-up time is entered/changed.

Phone settings

For details on performing audio settings and activat-
ing/deactivating warning and advisory tones and key
tones, see menu tree ¢ page 15.
For details on setting the display contrast and large
dialling numbers, see menu tree ¢ page 16.
For details on setting the system PIN on the base, see
menu tree ¢ page 16.

Changing the display language

Menu ¤ Settings ¤ OK ¤ Handset ¤ OK ¤ Language
q
¤ OK ¤ Select language ¤ OK
The current language is indicated by
If you accidentally choose a language you do not
understand:
421
¤ q Select language
¤
Menu
‰
¤
(
OK = selected)

Resetting the handset

You can reset individual settings and changes that
you have made. Entries in the directory, the call list
and the handset's registration to the base will be
retained.
a
. All participants hear
‰
.
12
Menu ¤ Settings ¤ OK ¤ Handset ¤ OK
¤ Reset Handset ¤ OK ¤ Reset? ¤ OK
Cancel the reset with
Resetting the base to the default
settings
When restoring factory settings:
u Individual settings are reset
u All lists are deleted
Only the date and time are retained.
Software reset
Menu ¤ Settings ¤ OK ¤ Base ¤ OK ¤ Base Reset ¤ OK
¤ Reset? ¤ OK
Hardware reset
Additionally
u All handsets are deregistered and
u The system PIN is reset to the original code 0000.
Disconnect the power cable from the base. Hold
down the registration/paging key (¢ page 1) on the
base and reconnect the power cable to the base at
the same time. Release the key after approximately
5 seconds.

Repeater mode

With a repeater you can increase the range of your
base. You will need to activate repeater mode
(¢ page 16). Repeater mode and Eco Mode or Eco
Mode+ (¢ page 2) cancel each other out. The default
encrypted transmission setting is deactivated when
repeater mode is activated.
After activating or deactivating the repeater, switch
your handset off and on again (¢ page 6).
Operating the base on the
PABX
The following settings are only necessary if your PABX
requires them, see the user guide for your PABX.
When entering the digits, enter them slowly one after
the other.
Changing the dialling mode
P#Q5#11
MENU ¤
set dialling mode flashes: 0 = tone dialling (DTMF);
1 = pulse dialling (PD) ¤
Setting recall
P#Q5#12
Menu ¤
the current recall flashes
2 = 120 ms; 3 = 400 ms; 4 = 250 ms; 5 = 300 ms;
6 = 600 ms; 7 = 800 ms ¤
a
.
¤ The number for the
¤ OK.
enter number
¤
The number for
: 0 = 80 ms; 1 = 100 ms;
¤ OK.
Enter number