Page 1 2013 F-650/750 Owner’s Manual fordowner.com ford.ca DC4J 19A321 AA November 2012 First Printing Owner’s Manual F-650/750 Litho in U.S.A.
Page 2: Table Of Contents
Table of Contents Introduction Vehicle Inspection Guide Child Safety Child seats ......... . .28 Child seat positioning .
Page 3 Table of Contents Windows and Mirrors Power windows ........58 Exterior mirrors .
Page 4: Table Of Contents
Table of Contents Fuel and Refueling Fuel quality .........111 Running out of fuel.
Page 5 Table of Contents Roadside Emergencies Getting roadside assistance ......181 Hazard flasher control........182 Jump-starting the vehicle .
Page 6: Table Of Contents
Table of Contents Vehicle Care Cleaning products........239 Cleaning the exterior .
Page 7 Errors and omissions excepted. © Ford Motor Company 2012 2013 F-650/750 (f67) Owners Guide gf, 1st Printing, October 2012...
Page 8: Introduction
Introduction ABOUT THIS MANUAL Thank you for choosing Ford. We recommend that you take some time to get to know your vehicle by reading this manual. The more that you know about it, the greater the safety and pleasure you will get from driving it.
Page 9 Introduction SYMBOL GLOSSARY WARNING: You risk death or serious injury to yourself and others if you do not follow the instruction highlighted by the warning symbol. These are some of the symbols you may see on your vehicle. Symbol Description Symbol Description Symbol Description Safety alert...
Page 10 Introduction Symbol Description Symbol Description Symbol Description Fuel pump Fuse Hazard reset compartment warning flasher Heated rear Interior Jack window luggage compartment release Lighting Low tire Maintain control pressure correct fluid warning level Panic alarm Parking aid Parking system brake system Power Power Power...
Page 11 In order to properly diagnose and service your vehicle, Ford Motor Company, Ford of Canada, and service and repair facilities may...
Page 12 Introduction FORD CREDIT (U.S. ONLY) Ford Credit offers a full range of financing and lease plans to help you acquire your vehicle. If you have financed or leased your vehicle through Ford Credit, thank you for your business. For your convenience, we offer a number of ways to contact us, as well as help manage your account.
Page 13 WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that you use extreme caution when using any device or feature that may take your focus off the road. Your primary responsibility is the safe operation of your vehicle.
Page 14 Introduction FEDERAL HIGHWAY ADMINISTRATION REGULATION Regulations such as those issued by the Federal Highway Administration or issued pursuant to the Occupational Safety and Health Act (OSHA), and state and local laws and regulations may require additional equipment for the way you intend to use the vehicle. It is the responsibility of the registered owner to determine the applicability of such laws and regulations to your intended use for the vehicle, and to arrange for the installation of required equipment.
Page 15: Vehicle Inspection Guide
Vehicle Inspection Guide VEHICLE INSPECTION INFORMATION To be sure your vehicle is ready to operate, conduct a pre-trip inspection at the beginning of each work period. Follow the steps listed in this section to ensure a proper vehicle inspection procedure. The pages in this section may be produced locally and used on a regular basis.
Page 16 Vehicle Inspection Guide Engine Compartment (with Engine Stopped) Engine Oil Use the dipstick to verify the oil level is in the proper operating range. See Engine oil check in the Maintenance chapter. Engine Coolant Look through the plastic reservoir or the clear sight glass on the reservoir (depending upon vehicle equipment) and verify the coolant level is within the proper operating range.
Page 17 Vehicle Inspection Guide Engine Starting (Parking Brake Applied) • Before entering the cab, verify that the vehicle Safety and Emergency is equipped with spare electrical fuses (if used), three red reflective triangles, a properly charged Equipment and rated fire extinguisher and wheel chocks. •...
Page 18 Vehicle Inspection Guide Engine Starting (Parking Brake Applied) Voltmeter Check the gauge (diesel engine) or indicator light (gasoline engine) to verify the alternator is charging. Steering Linkage Inspect for excessive free play in the steering Free Play linkages. The steering wheel should have less than 2 in.
Page 19 Vehicle Inspection Guide Engine Starting (Parking Brake Applied) Air Brakes Verify operation using the following procedure. Chock the wheels, if necessary. Push in the parking brake and, on tractors, push in the tractor parking brake knob: 1. Verify the air compressor or governor cut-out pressure is approximately 120 psi (827 kPa).
Page 20 Vehicle Inspection Guide Front of Vehicle Lights Verify: • all exterior lights illuminate and are clean • headlights function on high and low beam • reflectors are clean, unbroken and of proper color (red on rear, amber elsewhere) • running lights are clean and unbroken. Steering Gear Inspect for: •...
Page 21 Vehicle Inspection Guide Front Suspension Springs Inspect for leaves that may be: • missing • broken • shifted • in contact with (or nearly contacting) a tire, rim, brake drum, frame or body component. Note: Never apply grease to spring pads. Spring Mounts Inspect the following for cracks, breaks, wear, damage and tightness:...
Page 22 Vehicle Inspection Guide Front Brakes Drums Verify: • there are no cracks, dents, holes, and no loose or missing bolts • the brake linings are not worn, dangerously thin or contaminated by lubricant. Front Wheels Rims Inspect for damaged or bent rims. They should not have welding repairs, and there should be no rust trails that indicate it is loose on the wheel.
Page 23 Vehicle Inspection Guide Underbody Driveshaft Verify: • the driveshaft is not bent or cracked • all driveshaft couplings are secure. Exhaust System Verify: • the visible outside parts are securely mounted • there are no cracks, holes or severe dents. •...
Page 24 Vehicle Inspection Guide Rear of Vehicle Lights and Verify: • all exterior lights illuminate and are clean Reflectors • reflectors are clean, unbroken and of proper color (red on rear, amber elsewhere) • running lights are clean and unbroken. Note: Rear running lights must be inspected separately from signal, flasher and brake lights.
Page 25 Vehicle Inspection Guide Rear Suspension • Verify torsion arm is not cracked, broken or Torsion Arm and Shock Absorbers missing. • Inspect the shock absorber for cracks or leaks. There should be no missing or broken mounting bolts or worn bushings. Rear Brakes •...
Page 26 Vehicle Inspection Guide Trailer If you are pulling a trailer, an inspection of the trailer similar to that of the tractor should be done. The inspection should follow trailer manufacturer recommendations and should include at a minimum: general condition, landing gear, doors, sides, lights, reflectors, suspension, brakes, tires, wheels, cargo placement, stability and tie-downs.
Page 27: Child Safety
NHTSA and other safety organizations, or are the minimum requirements of law. Ford recommends checking with a NHTSA Certified Child Passenger Safety Technician and consulting your pediatrician to make sure your child seat is appropriate for your child, and is compatible with and properly installed in your vehicle.
Page 28 Child Safety Recommendations for Safety Restraints for Children Child size, height, weight, or Recommended restraint type Small Children who have outgrown or no Use a belt-positioning children longer properly fit in a child safety booster seat. seat (generally children who are less than 4 ft.
Page 29: Child Seats
Child Safety CHILD SEATS Use a child safety seat (sometimes called an infant carrier, convertible seat, or toddler seat) for infants, toddlers or children weighing 40 pounds (18 kilograms) or less (generally age four or younger). CHILD SEAT POSITIONING WARNING: Airbags can kill or injure a child in a child seat. Never place a rear-facing child seat in front of an active airbag.
Page 30 Child Safety WARNING: Always restrain an unoccupied child seat or booster seat. These objects may become projectiles in a crash or sudden stop, which may increase the risk of serious injury. WARNING: Never place, or allow a child to place, the shoulder belt under a child’s arm or behind the back because it reduces the protection for the upper part of the body and may increase the risk of injury or death in a crash.
Page 31: Booster Seats
Child Safety BOOSTER SEATS WARNING: Never place, or allow a child to place, the shoulder belt under a child’s arm or behind the back because it reduces the protection for the upper part of the body and may increase the risk of injury or death in a crash.
Page 32 Child Safety Types of Booster Seats • Backless booster seats If your backless booster seat has a removable shield, remove the shield. If a vehicle seating position has a low seat back or no head restraint, a backless booster seat may place your child’s head (as measured at the tops of the ears) above the top of the seat.
Page 33 Child Safety Children and booster seats vary in size and shape. Choose a booster that keeps the lap belt low and snug across the hips, never up across the stomach, and lets you adjust the shoulder belt to cross the chest and rest snugly near the center of the shoulder.
Page 34: Installing Child Safety Seats
Child Safety INSTALLING CHILD SAFETY SEATS Using Automatic Locking Mode Combination Lap and Shoulder Belts (Front Passenger and Rear Outboard Seating Positions) WARNING: Children 12 and under should be properly restrained in the rear seat whenever possible. WARNING: Depending on where you secure a child restraint, and depending on the child restraint design, you may block access to certain safety belt buckle assemblies and/or LATCH lower anchors, rendering those features potentially unusable.
Page 35 Child Safety 2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together. 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer’s instructions.
Page 36 Child Safety 5. To put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is pulled out. • Allow the belt to retract to remove slack. The belt will click as it retracts to indicate it is in the automatic locking mode.
Page 37 There should be no more than one inch (two and a half centimeters) of movement for proper installation. Ford recommends checking with a NHTSA Certified Child Passenger Safety Technician (CPST) to make certain the child restraint is properly installed.
Page 38 Child Safety The tether strap anchors in your vehicle are in the following positions (shown from top view): • Regular Cab • Crew Cab Attach the tether strap only to the appropriate tether anchor as shown. The tether strap may not work properly if attached somewhere other than the correct tether anchor.
Page 39 If the safety seat is not anchored properly, the risk of a child being injured in a crash greatly increases. If your child restraint system is equipped with a tether strap, and the child restraint manufacturer recommends its use, Ford also recommends its use. Tether Strap Attachment (Rear SuperCab Only) There are three loops of webbing just above the back of the rear seat (along the bottom edge of the rear window) in the SuperCab.
Page 40 Child Safety Many tether straps cannot be tightened if the tether strap is hooked to the loop directly behind the child seat. To provide a tight tether strap: 1. Route the tether strap through the loop directly behind the child seat.
Page 41: Child Safety Locks
Child Safety CHILD SAFETY LOCKS (IF EQUIPPED) When these locks are set, the rear doors cannot be opened from the inside. The childproof locks are located on the rear edge of each rear door and must be set separately for each door.
Page 42: Safety Belts
Safety Belts PRINCIPLES OF OPERATION WARNING: Always drive and ride with your seat back upright and the lap belt snug and low across the hips. WARNING: To reduce the risk of injury, make sure children sit where they can be properly restrained. WARNING: Never let a passenger hold a child on his or her lap while the vehicle is moving.
Page 43: Fastening The Safety Belts
Safety Belts WARNING: Safety belts and seats can become hot in a vehicle that has been closed up in sunny weather; they could burn a small child. Check seat covers and buckles before you place a child anywhere near them. WARNING: Front and rear seat occupants, including pregnant women, should wear safety belts for optimum protection in an accident.
Page 44 Safety Belts 2. To unfasten, press the release button and remove the tongue from the buckle. Using the Safety Belt with Cinch Tongue (Front and Rear Center Seat) The cinch tongue slides up and down the belt webbing when the belt is stowed or while putting safety belts on.
Page 45 Safety Belts 2. Be sure the belt is not twisted. If the belt is twisted, remove the twist. 3. Insert the belt tongue into the proper buckle for your seating position until you hear a snap and feel it latch. 4.
Page 46 Safety Belts safety belt have the first locking mode described below only. All outboard passenger and outboard rear safety belts have both types of locking modes described as follows: Vehicle Sensitive Mode This is the normal retractor mode, which allows free shoulder belt length adjustment to your movements and locking in response to vehicle movement.
Page 47 Safety Belts How to Disengage the Automatic Locking Mode WARNING: After any vehicle crash, the safety belt system at all passenger seating positions must be checked by an authorized dealer to verify that the “automatic locking retractor” feature for child seats is still functioning properly.
Page 48: Safety Belt Height Adjustment
Safety Belts SAFETY BELT HEIGHT ADJUSTMENT WARNING: Position the safety belt height adjusters so that the belt rests across the middle of your shoulder. Failure to adjust the safety belt properly could reduce the effectiveness of the safety belt and increase the risk of injury in a crash. Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder.
Page 49: Safety Belt-Minder
Safety Belts SAFETY BELT-MINDER® This feature supplements the safety belt warning function by providing additional reminders by intermittently sounding a chime and illuminating the safety belt warning light when the driver’s seat is occupied and the safety belt is unbuckled. If...
Page 50 Safety Belts Read Steps 1-4 thoroughly before proceeding with the deactivation or activation programming procedure. The system can be deactivated and activated by performing the following procedure: Before following the procedure, make sure that: • the parking brake is set •...
Page 51: Child Restraint And Safety Belt Maintenance
Read the child restraint manufacturer’s instructions for additional inspection and maintenance information specific to the child restraint. Ford Motor Company recommends that all safety belt assemblies in use in vehicles involved in a crash be replaced.
Page 52: Keys And Remote Control
Keys and Remote Control KEYS The key operates all locks on your vehicle. In case of loss, replacement keys are available from your dealer. You should always carry a second key with you in a safe place in case you require it in an emergency. 2013 F-650/750 (f67) Owners Guide gf, 1st Printing, October 2012 USA (fus)
Page 53: Locks
Locks LOCKING AND UNLOCKING You can use the power door lock control to lock and unlock the vehicle. Power Door Locks (If Equipped) The power door lock control is located on the driver and front passenger door panels. A. Unlock B.
Page 54: Steering Wheel Controls
Steering Wheel ADJUSTING THE STEERING WHEEL WARNING: Do not adjust the steering wheel when your vehicle is moving. 1. Pull and hold the steering wheel release lever. 2. Adjust the steering wheel to the desired position then release the lever. VOICE CONTROL (IF EQUIPPED) A.
Page 55: Wipers And Washers
Wipers and Washers WINDSHIELD WIPERS Note: Fully defrost the windshield in icy conditions before turning on the windshield wipers. Rotate the end of the control away from you to increase the speed of the wipers. Rotate toward you to decrease the speed of the wipers. WINDSHIELD WASHERS Note: Do not operate the wipers on a dry windshield.
Page 56: Lighting
Lighting LIGHTING CONTROL • Rotate the headlamp control clockwise to the first position to turn on the parking lamps. • Rotate clockwise to the second position to also turn on the headlamps. High Beams • Push the lever toward the instrument panel to activate.
Page 57: Instrument Lighting Dimmer
Lighting INSTRUMENT LIGHTING DIMMER Use to adjust the brightness of the instrument panel and all applicable lit components in the vehicle during headlamp and parking lamp operation. • Tap the top or bottom of the control to brighten or dim all interior lit components incrementally, or •...
Page 58: Turn Signal Control
Lighting DIRECTION INDICATORS • Push down to activate the left turn signal. • Push up to activate the right turn signal. If your vehicle is a tractor, the turn signals may not shut off when a turn is completed. This is normal. See your dealer if there are any questions about your vehicle’s options.
Page 59: Windows And Mirrors
Windows and Mirrors POWER WINDOWS (IF EQUIPPED) WARNING: Do not leave children unattended in your vehicle and do not let them play with the power windows. They may seriously injure themselves. WARNING: When closing the power windows, you should verify they are free of obstructions and make sure that children and pets are not in the proximity of the window openings.
Page 60 Windows and Mirrors Bounce-Back (One-Touch Up or Down Windows Only) The window will stop automatically while closing and reverse some distance if there is an obstacle in the way. Overriding the Bounce-Back Feature WARNING: When you override the bounce-back feature the window will not reverse if it detects an obstacle.
Page 61: Exterior Mirrors
Windows and Mirrors EXTERIOR MIRRORS With the doors closed and the seat adjusted for proper comfort, move the mirrors to maximize rear viewing area by adjusting the mirrors left or right as required. Adjust the auxiliary convex mirrors. Convex mirrors are a ball-stud design for precise adjustment to maximize viewing area.
Page 62 Windows and Mirrors Power Exterior Mirrors (If Equipped) WARNING: Do not adjust the mirror while the vehicle is in motion. A. Left-hand mirror B. Off C. Right-hand mirror To adjust your mirrors: 1. Select the mirror you want to adjust. 2.
Page 63 Windows and Mirrors If the click is not heard, use the control to fold the mirrors all the way out, then in again. Once the click is heard the mirrors will operate normally until they are again manually folded. Heated Exterior Mirror (If Equipped) The heated exterior mirrors switch on with the heated mirror switch.
Page 64: Instrument Cluster
Instrument Cluster GAUGES - DIESEL ENGINE Cluster shown in standard measure. Metric similar. A. Engine oil pressure gauge B. Engine coolant temperature gauge C. Diesel exhaust fluid (DEF) gauge D. Fuel gauge E. Speedometer F. Information display. See the Information Displays chapter for more information.
Page 65 Instrument Cluster Engine Coolant Temperature Gauge Indicates engine coolant temperature. At normal operating temperature, the level indicator is in the normal range. If the engine coolant temperature exceeds the normal range, stop the vehicle as soon as safely possible, switch off the engine and let the engine cool. WARNING: Never remove the coolant reservoir cap while the engine is running or hot.
Page 66 Instrument Cluster GAUGES - GASOLINE ENGINE Cluster shown in standard measure. Metric similar. A. Engine oil pressure gauge B. Engine coolant temperature gauge C. Transmission fluid temperature gauge D. Fuel gauge E. Speedometer F. Information display. See the Information Displays chapter for more information.
Page 67 Instrument Cluster Engine Coolant Temperature Gauge Indicates engine coolant temperature. At normal operating temperature, the level indicator is in the normal range. If the engine coolant temperature exceeds the normal range, stop the vehicle as soon as safely possible, switch off the engine and let the engine cool. WARNING: Never remove the coolant reservoir cap while the engine is running or hot.
Page 68: Warning Lamps And Indicators
Instrument Cluster Gauge Package (If Equipped) Your vehicle may be equipped with an optional gauge package which has one of the following configurations: 1. Transmission temperature gauge: Displays the transmission temperature at the transmission sump. 2. Hourmeter: Displays the hours of engine run time.
Page 69 Instrument Cluster WARNING: Driving a vehicle with the brake system warning light on is dangerous. A significant decrease in braking performance may occur. It takes you longer to stop the vehicle. Have the vehicle checked by your authorized dealer. Driving extended distances with the parking brake engaged can cause brake failure and the risk of personal injury.
Page 70 Instrument Cluster Diesel Exhaust Fluid (diesel engine only) It illuminates when the diesel exhaust fluid level falls below 0.5 gallons (1.9L) in the five gallon (19.0L) tank or one gallon (3.8L) in the nine gallon (34.0L) tank. Refill the tank or, at a minimum, add at least one gallon (3.8L) to the five gallon (19.0L) tank or two gallons (7.6L) to the nine gallon (34.0L) tank.
Page 71 Instrument Cluster High Beam It illuminates when the headlamp high beam is switched on. Low Fuel Level (gasoline engine only) It illuminates when the fuel level is low or near empty. Refuel as soon as possible. Parking Brake Warning It momentarily illuminates when the ignition is switched to the on position (with the engine off).
Page 72 Instrument Cluster Stop Engine (diesel engine only) This red lamp illuminates when the engine needs to be stopped (as soon as it can be safely done). If the lamp begins flashing, automatic engine shutdown may take place in as little as 20 seconds.
Page 73: Audible Warnings And Indicators
Instrument Cluster Water in Fuel (diesel engine only) It illuminates when the fuel filter/water separator has a significant quantity of water in it. If the light illuminates when the engine is running, stop the vehicle as soon as safely possible, shut off the engine, then drain the fuel filter/water separator.
Page 74: Information Displays
GENERAL INFORMATION WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that drivers use extreme caution when using any device or feature that may take their focus off the road. Your primary responsibility is the safe operation of the vehicle.
Page 75 Information Displays • MILES (KILOMETERS) TO E: This displays an estimate of approximately how far you can drive with the fuel remaining in your tank under normal driving conditions. Remember to turn the ignition off when refueling to allow this feature to correctly detect the added fuel.
Page 76: Information Messages
Information Displays INFORMATION MESSAGES Note: Depending on the vehicle options equipped with your vehicle, not all of the messages display or are available. Certain messages may be abbreviated or shortened depending upon which cluster type you have. Press the OK button to acknowledge and remove some messages from the information display.
Page 77 Due to technical incompatibility, certain recordable and re-recordable compact discs may not function correctly when used in Ford CD players. Note: Do not insert CDs with homemade paper (adhesive) labels into the CD player as the label may peel and cause the CD to become jammed.
Page 78 Audio System MP3 Track and Folder Structure Audio systems capable of recognizing and playing MP3 individual tracks and folder structures work as follows: • There are two different modes for MP3 disc playback: MP3 track mode (system default) and MP3 folder mode. •...
Page 79: Audio System Am/Fm Stereo
AUDIO WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that you use extreme caution when using any device or feature that may take your focus off the road. Your primary responsibility is the safe operation of your vehicle.
Page 80: Am/Fm/Cd With Sync
AM/FM/CD WITH SYNC® WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that you use extreme caution when using any device or feature that may take your focus off the road. Your primary responsibility is the safe operation of your vehicle.
Page 81 Audio System D. Phone: Press this button to access the phone features of the SYNC® system. See the SYNC® chapter for more information. E. MENU: Press this button to access different audio system features. • If your vehicle is equipped with satellite radio, you can access different menus by pressing OK.
Page 82: Auxiliary Input Jack
AUXILIARY INPUT JACK WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that you use extreme caution when using any device or feature that may take your focus off the road. Your primary responsibility is the safe operation of your vehicle.
Page 83 Audio System WARNING: Store the portable music player in a secure location, such as the center console or the glove box, when your vehicle is moving. Hard objects may become projectiles in a crash or sudden stop, which may increase the risk of serious injury. The audio extension cable must be long enough to allow the portable music player to be safely stored while your vehicle is moving.
Page 84: Usb Port
USB PORT (IF EQUIPPED) WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that you use extreme caution when using any device or feature that may take your focus off the road. Your primary responsibility is the safe operation of your vehicle.
Page 85 Note: SIRIUS reserves the unrestricted right to change, rearrange, add or delete programming including canceling, moving or adding particular channels, and its prices, at any time, with or without notice to you. Ford Motor Company shall not be responsible for any such programming changes.
Page 86 Audio System Troubleshooting Radio display Condition Possible action Acquiring Radio requires more No action required. This than two seconds to message should produce audio for the disappear shortly. selected channel. Sat Fault/SIRIUS There is an internal If this message does not system failure module or system failure clear shortly, or with an...
Page 87: Climate Control
Climate Control MANUAL CLIMATE SYSTEM MAX A/C A. Defrost: Distributes air through the windshield defroster vents and demister vents. This setting can also be used to defog and clear the windshield of a thin covering of ice. B. Heated mirrors: Turns the heated mirrors on and off. See Heated mirrors later in this chapter for more information.
Page 88 Climate Control E. Recirculated air: Press to switch between outside air and recirculated air. When the LED on the button is lit, the air currently in the passenger compartment is being recirculated. Using recirculated air can reduce the time needed to cool the interior and reduce unwanted odors from entering your vehicle.
Page 89 Climate Control Gas engines: If your vehicle is stationary for long periods of time in high ambient temperature conditions, your climate control system may automatically switch from fresh air mode to recirculation mode. This is normal system operation as it provides protection of the air conditioning compressor (and related parts).
Page 90: Seats
Seats SITTING IN THE CORRECT POSITION WARNING: Do not recline the seat back as this can cause the occupant to slide under the seat’s safety belt, resulting in severe personal injury in the event of a crash. WARNING: Do not place objects higher than the seat backs to reduce the risk of injury in a crash or during heavy braking or when stopping suddenly.
Page 91: Head Restraints
Seats HEAD RESTRAINTS WARNING: To minimize the risk of neck injury in the event of a crash, you and the passenger occupants should not sit in or operate the vehicle, until the head restraint is placed in its proper position. Never adjust the head restraint while the vehicle is in motion. WARNING: The adjustable head restraint is a safety device.
Page 92 Seats Front Row Center, Outboard (Crew Cab), and Rear Seat Center (Crew Cab) Head Restraints Your vehicle may be equipped with head restraints that are non-adjustable. The non-adjustable head restraints consist of: A. An energy absorbing head restraint B. Two steel stems C.
Page 93: Manual Seats
Seats Remove - Front Row Center, Outboard (Crew Cab), and Rear Seat Center (Crew Cab) Head Restraints 1. Pull up the head restraint until it reaches the highest adjustment position. 2. Press and hold buttons C. 3. Pull up the head restraint. Reinstall Align the steel stems into the guide sleeves and push the head restraint down until it locks.
Page 94 Seats Tilting the Seat Back Forward (Two-passenger Bench Seat) Manual Lumbar (If Equipped) The lumbar support control is located on the outboard side of the seat. Turn the control to adjust your support. 2013 F-650/750 (f67) Owners Guide gf, 1st Printing, October 2012 USA (fus)
Page 95: Power Seats
Seats POWER SEATS WARNING: Never adjust the driver’s seat when the vehicle is moving. WARNING: To reduce the risk of excess slack in the belt system, always adjust the seat height before fastening the seat belt. Non Air-Ride Seat The control is located on the outboard side of the seat cushion. •...
Page 96 Seats Air-Ride Seat A. Recline: Lift the handle to adjust the angle of the seat back. B. Power lumbar: • Press the top of the forward control to inflate the lower lumbar support. • Press the bottom of the forward control to deflate the lower lumbar support.
Page 97: Rear Seats
Seats REAR SEATS Folding Up the Rear Seats (SuperCab) 1. Pull the control to release the seat cushion. 2. Rotate the seat cushion up until it locks into the vertical storage position. Returning the Seat to the Seating Position WARNING: Make sure that cargo or any objects are not trapped underneath the seat cushion before returning the seat cushion to its original position, and that the seat cushion locks into place.
Page 98: Heated Seats
Seats REAR SEAT ARMREST (IF EQUIPPED) To use the armrest, rotate it forward from the seat back. HEATED SEATS (IF EQUIPPED) WARNING: Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion, or other physical conditions, must exercise care when using the seat heater.
Page 99 Seats FRONT SEAT ARMREST (IF EQUIPPED) To release the armrest and gain access to the cupholders and seat back storage bin, press the button on the right-hand side of the seat and pull the seat back down. Pull up on the tab to open the storage bin.
Page 100: Auxiliary Power Points
Auxiliary Power Points AUXILIARY POWER POINTS WARNING: Do not plug optional electrical accessories into the cigarette lighter socket (if equipped). Improper use of the lighter can cause damage not covered by your warranty, and can result in fire or serious injury. Note: If used when the engine is not running, the battery will discharge.
Page 101: Starting And Stopping The Engine
Starting and Stopping the Engine GENERAL INFORMATION WARNING: Extended idling at high engine speeds can produce very high temperatures in the engine and exhaust system, creating the risk of fire or other damage. WARNING: Do not park, idle, or drive your vehicle on dry grass or other dry ground cover.
Page 102: Ignition Switch
Starting and Stopping the Engine IGNITION SWITCH Note: When you switch the ignition off and leave your vehicle, do not leave your key in the ignition. This could discharge your vehicle battery. A. Accessory: Allows the electrical accessories, such as the radio, to operate while the engine is not running.
Page 103 Starting and Stopping the Engine Some warning lights briefly illuminate. Note: Do not touch the accelerator pedal. 1. Fully press the brake pedal. 2. Turn the key to start the engine. The engine may continue cranking for up to 15 seconds or until the vehicle starts. Note: If the engine does not start on the first try, wait for a short period of time and try again.
Page 104 Starting and Stopping the Engine STARTING A DIESEL ENGINE WARNING: Operation of a diesel engine near flammable vapors in the air may cause the engine speed to increase uncontrollably and over speed. If this situation occurs, mechanical damage, fire, explosion, personal injury or death could result. Turning off the ignition key does not slow or stop the engine due to uncontrollable fueling of the engine through flammable vapors being drawn into the engine air inlet.
Page 105 Starting and Stopping the Engine Note: Idle the engine for three to five minutes before operating with a full load. Note: Try to limit engine idle to 10 minutes. Excessive idling reduces fuel economy. Vehicles with a Manual Transmission Note: Do not touch the accelerator pedal. 1.
Page 106 Starting and Stopping the Engine Regeneration Unlike a normal filter which requires periodic replacement, the DPF has been designed to regenerate, or clean itself to maintain operating efficiency. The regeneration process takes place automatically. A small increase in engine/turbo sound-level is normal during filter regeneration. However, some driving conditions mean that you may need to support the regeneration process: •...
Page 107 1. Bring the vehicle to a complete stop on level ground and safely off the road with the exhaust system away from people, flammable materials, vapors or structures. Ford recommends that you perform a walk-around before beginning a parked regeneration.
Page 108 Starting and Stopping the Engine On average (depending on filter level and other factors), the process takes 20–30 minutes to complete. The DPF lamp turns off when the process is complete. Repeat Steps 1–5, if parked regeneration is interrupted. To Discontinue Parked Regeneration Press any of the floor pedals to discontinue parked regeneration.
Page 109: Engine Block Heater
Starting and Stopping the Engine The inlet holes in the side of the assembly are functional. These holes allow outside air to be drawn into the outlet assembly. The holes need to be kept clear of mud and other foreign material to maintain proper functionality of the system.
Page 110 Starting and Stopping the Engine The heater acts as a starting aid by warming the engine coolant. This allows the climate control system to respond quickly. The equipment includes a heater element (installed in the engine block) and a wire harness.
Page 111: Fuel And Refueling
Fuel and Refueling SAFETY PRECAUTIONS WARNING: Do not overfill the fuel tank. The pressure in an overfilled tank may cause leakage and lead to fuel spray and fire. WARNING: The fuel system may be under pressure. If you hear a hissing sound near the fuel filler inlet, do not refuel until the sound stops.
Page 112: Fuel Quality
Fuel and Refueling • Avoid getting fuel liquid in your eyes. If fuel is splashed in the eyes, remove contact lenses (if worn), flush with water for 15 minutes and seek medical attention. Failure to seek proper medical attention could lead to permanent injury.
Page 113 Fuel and Refueling WARNING: Do not mix diesel fuel with gasoline, gasohol or alcohol. This could cause an explosion resulting in personal injury. WARNING: Do not use starting fluid such as ether or gasoline. Such fluids can cause immediate explosive damage to the engine and possible personal injury.
Page 114: Running Out Of Fuel
Fuel and Refueling Octane Recommendations - Gasoline Engines Regular unleaded gasoline with a pump (R+M)/2 octane rating of 87 is recommended. Some stations offer fuels posted as Regular with (R+M)/2 METHOD an octane rating below 87, particularly in high altitude areas. Do not use fuels with a posted octane rating below 87.
Page 115: Refueling
Fuel and Refueling • The fuel system must be primed before attempting to restart the engine. See your engine operator’s manual for instructions on priming the engine. • Use caution not to overheat and damage the starter by cranking the engine for an excessive period of time.
Page 116 The customer warranty may be void for any damage to the fuel tank or fuel system if the correct genuine Ford, Motorcraft® or other certified fuel filler cap is not used. Your fuel tank filler cap has an indexed design with a ⁄...
Page 117: Fuel Consumption
Fuel and Refueling FUEL CONSUMPTION Filling the Tank The advertised capacity is the indicated capacity and the empty reserve combined. Indicated capacity is the difference in the amount of fuel in a full tank and a tank when the fuel gauge indicates empty. Empty reserve is the amount of fuel in the tank after the fuel gauge indicates empty.
Page 118: Diesel Exhaust Fluid (Def)
Fuel and Refueling 5. Calculate fuel economy as follows: • Standard: Divide miles traveled by gallons used. • Metric: Multiply liters used by 100, then divide by kilometers traveled. Keep a record for at least one month and record the type of driving (city or highway).
Page 119 Fuel and Refueling Continued driving without refilling results in the following actions as required by the U.S. Environmental Protection Agency (EPA): Low DEF Level Warning Indications and Vehicle Consequences Indicator DEF Tank Level Consequence Remedy Lamps Above initial warning threshold None.
Page 120 Fuel and Refueling Low DEF Level Warning Indications and Vehicle Consequences for Emergency Vehicles Indicator DEF Tank Level Consequence Remedy Lamps Above initial warning threshold None. None. None. (Over 25% full). Below initial warning None. DEF solid Add 1 gallon threshold (25% full).
Page 121 Amber engine from 25% to Replace DEF DEF quality is solid 40% at rate of with detected. 1% each Ford-approved minute. Final vehicle • 25% torque consequence three reduction hours after incorrect • 5 mph Amber engine DEF quality is...
Page 122 10 hours after limited to incorrect DEF 55 mph solid quality is detected. (88 km/h). Replace DEF Final vehicle with consequence Ford-approved 20 hours after DEF. incorrect DEF Amber engine Vehicle speed quality is detected solid limited to and engine 25 mph...
Page 123 Fuel and Refueling SCR Faults and Vehicle Consequences Indicator Condition Consequence Remedy Lamps No faults. None. None. None. Amber engine Initial warning when None. fault is detected. solid Initial warning one Amber engine 25% torque hour after fault is solid reduction.
Page 124 Fuel and Refueling SCR Faults and Vehicle Consequences for Emergency Vehicle Indicator Condition Consequence Remedy Lamps No faults. None. None. None. Amber engine Initial warning when None. fault is detected. solid Vehicle speed Initial warning Amber engine limited to 10 hours after fault 55 mph solid is detected.
Page 125 Fuel and Refueling Filling the DEF Tank WARNING: Make sure that DEF does not come into contact with eyes, skin or clothing. Should DEF contact your eyes, flush them with plenty of water and contact a physician. Clean affected skin with soap and water.
Page 126 Fuel and Refueling Use Motorcraft® DEF or equivalent meeting Ford specification WSS-M2C130-A and/or ISO 22241. Use only DEF certified by the American Petroleum Institute. Look for this certification trademark. Repairs resulting from the use of non-certified DEF products may not be covered by your vehicle’s warranty.
Page 127 Fuel and Refueling 2. Open the DEF filler port on the vehicle by turning the blue cap counterclockwise a ⁄ -turn. 3. Lift and hold the DEF container, without tipping, and insert the spout, into the DEF filler port. 4. Lift and tip the container to let DEF flow into the tank.
Page 128 Fuel and Refueling DEF Filling Station Nozzle Fill Filling the DEF tank using a nozzle is similar to a normal fuel fill. The nozzle shuts off automatically when the tank is full. Do not continue to fill the tank as this may cause spillage and overfill the tank, which can cause damage.
Page 129 Fuel and Refueling DEF Guidelines and Information • DEF is non-flammable, non-toxic, colorless and water-soluble. • Use only DEF that carries the trademark: AMERICAN PETROLEUM INSTITUTE CERTIFIED DIESEL EXHAUST FLUID. • An ammonia odor may be smelled when the cap is removed or during a refill.
Page 130 Fuel and Refueling Engine: Valve covers and block covers are made to damp-out engine mechanical noise and, if needed, should be replaced with recommended parts. Check for mechanical isolations. Transmission Enclosure: Inspect for cracks, holes and tears. Clean any deposits, such as oil, dirt and stones. Exhaust System: •...
Page 131: Transmission
Transmission MANUAL TRANSMISSION OPERATION (IF EQUIPPED) Manual transmission shift patterns are displayed on either the shift lever knob or the sun visor. Study this information carefully before you drive the vehicle even though you may be familiar with similar units. Do not attempt to drive the vehicle without knowing the exact shift pattern of the transmission.
Page 132 Transmission Shifting with a Non-Synchronized Transmission See Clutch brake and Double clutch procedures in the Clutch section of this chapter. Clutch Do not ride or slip the clutch as this causes unnecessary heat and wear. Maintain the specified clutch adjustment to prolong its life and regularly inspect the clutch control linkage for tightness.
Page 133 Transmission If the transmission is equipped with a ceramic clutch, you must start the vehicle moving in first gear and engage the clutch before pressing the accelerator at idle. Also, do not try to slip the clutch by raising engine RPM and riding or feathering the clutch pedal since this causes erratic engagement which can cause engine stalling and potential serious damage to driveline components.
Page 134 Transmission Eaton FS-5205A 5–speed This transmission is equipped with five forward gears and one reverse; gears 2–5 are synchronized. The shift pattern is embossed on the gear shift knob. Do not shift the transmission into reverse while the vehicle is moving as this could damage the transmission.
Page 135: Transmission Operation
Transmission AUTOMATIC TRANSMISSION OPERATION (IF EQUIPPED) WARNING: Hold the brake pedal down while you move the gearshift lever between positions. If you do not hold the brake pedal down, your vehicle may move unexpectedly and cause property damage, personal injury or death. Main transmission, auxiliary transmission, transfer case and power take-off (PTO) control shift patterns can be found on a placard or decal on the driver’s sun visor, on the instrument panel or on the shift control...
Page 136 Transmission WARNING: If the parking brake is fully released, but the brake warning lamp remains illuminated, the brakes may not be working properly. See your authorized dealer. If the fuse is not blown and the brake lamps are working properly, the following procedure allows you to move the gearshift lever from position P: 1.
Page 137 Transmission Six–speed TorqShift® Transmission WARNING: Always set the parking brake fully and make sure the gearshift is latched in position P. Turn the ignition to the off position and remove the key whenever you leave your vehicle. WARNING: Do not use the tow/haul feature when driving in icy or slippery conditions as the increased engine braking can cause the rear wheels to slide and the vehicle to swing around with the possible loss of vehicle control.
Page 138 Transmission Position 2 Use position 2 to start-up on slippery roads or to provide additional engine braking on downgrades. Position 1 • Provides maximum engine braking. • Allows upshifts by moving gearshift lever. • The transmission does not downshift into position 1 at high speeds; it downshifts to a lower gear and then shifts into position 1 when the vehicle reaches slower speeds.
Page 139 Transmission Allison 2500 WARNING: To avoid sudden, unexpected vehicle movement and possible personal injury or death: 1. Bring the vehicle to a complete stop. 2. Shift the transmission into position N. 3. Apply the parking brake and make sure it is holding properly. 4.
Page 140 Transmission Allison 3000 Series Push-Button Shifter To shift to Reverse or Drive: 1. Press the brake pedal. 2. Press R or D on the shifter. 3. Release the brake pedal. To select a higher range when in Drive, press the up arrow button. To select a lower range when in Drive, press the down arrow button.
Page 141 Transmission PTO Operation with Vehicle Stationary WARNING: When the PTO is operated with the vehicle stationary, the transmission must be placed in position N with the parking brake set. If the transmission is not in position N and is equipped with a remote throttle control, an increase in engine speed can overpower the parking brake and cause the vehicle to move, possibly resulting in personal injury and/or property damage.
Page 142 Transmission REAR AXLES Gross Axle Weight WARNING: Exceeding these ratings by overloading can cause component failure resulting in property damage, personal injury or death. Your truck has gross axle weight, gross vehicle weight and gross combination weight ratings. Do not exceed these ratings. Locking or Limited-Slip Differentials WARNING: If both wheels are not raised off the ground, the one wheel that is not raised may pull the vehicle off its support,...
Page 143 Transmission Turn the engine off and raise all drive wheels of the locker differential axle in order to prevent the vehicle from moving when servicing the wheels, tires or brakes. Axles equipped with a NoSPIN Detroit Locker differential deliver power to both wheels even when only one wheel is on the ground.
Page 144 Transmission TWO-SPEED REAR AXLE (IF EQUIPPED) WARNING: Never shift a two-speed axle when descending a steep grade as this may cause loss of vehicle control and result in personal injury. Note: Do not shift between ranges when the speed control is on. A two-speed rear axle allows the driver to select a low range for greater pulling power and a high...
Page 145 Transmission To shift the axle from LOW to HIGH with the vehicle moving, accelerate to approximately 35 mph (56 km/h), press the lower part of the switch while the transmission is in position N, then release and apply the accelerator. To shift the axle from HIGH to LOW with the vehicle stopped, place the transmission in position N, then press the upper part of the switch.
Page 146: Brakes
Brakes GENERAL INFORMATION All standard equipment brakes are designed to be self-adjusting. Automatic adjustment, when required, occurs whenever the brakes are applied and released during forward or reverse operation. Note: Occasional brake noise is normal. If a metal-to-metal, continuous grinding or continuous squeal sound is present, the brake linings may be worn out and should be inspected by an authorized dealer.
Page 147 Brakes Anti-lock Brake System (ABS) This system helps you maintain steering control during emergency stops by keeping the brakes from locking. The ABS lamp momentarily illuminates when the ignition is turned on. If the light does not illuminate during start-up, remains on or flashes, the ABS may be disabled and may need to be serviced.
Page 148 Brakes AIR BRAKES After starting the engine, give the air compressor time to build up the air pressure to 60 psi (414 kPa) before moving the vehicle. WARNING: Do not drive or continue to drive if the low air pressure buzzer is sounding or the brake warning light is lit. These warnings indicate that air pressure is not to normal operating level.
Page 149 Brakes Air Chamber Stroke Indication Air chamber push rods have orange stroke indicator markers that warn when the braking system requires adjustment or repair. The orange stripe is painted on the air chamber push rod at the slack adjuster stroke dimension which requires service when visible during brake application.
Page 150: Hints On Driving With Anti-Lock Brakes
Brakes HINTS ON DRIVING WITH ANTI-LOCK BRAKES When the system is operating, the brake pedal pulses and may travel further. Maintain pressure on the brake pedal. You may also hear a noise from the system. This is normal. The ABS does not eliminate the dangers inherent when: •...
Page 151 Brakes A switch on the instrument panel, in combination with the accelerator and clutch pedal, allows the operator to make maximum use of the exhaust brake in the following conditions: • off-highway driving • mountain driving • heavy traffic • high-speed highway driving. To operate the brake, push the switch up to turn it on.
Page 152 Brakes • Engine temperature remaining in the normal operating range. • The tachometer showing a drop in engine RPM (depending on grade and vehicle load) during a descent. • A decrease in road speed when the exhaust brake is applied during a descent, except when the vehicle is carrying a heavy load or the grade is extremely steep.
Page 153 Brakes Trailer Air Supply and Parking Brake Modular Controls (If Equipped) The trailer air supply valve delivers air to the trailer supply and automatically pops out, shutting off the trailer supply, if pressure decreases to approximately 35 psi (249 kPa). The parking brake controls the spring brakes on the tractor.
Page 154 Brakes The parking brake (B – yellow knob) can now be pushed in and supply air to the tractor spring brakes, releasing them. Normal Driving Position With both knobs pushed in, air is supplied to both trailer and tractor spring brakes and all brakes are released. 2013 F-650/750 (f67) Owners Guide gf, 1st Printing, October 2012 USA (fus)
Page 155 Brakes System Park With both knobs pushed in (normal driving position), the parking brakes for both the tractor and trailer can be applied by pulling the parking brake knob (B) out, exhausting air from the tractor spring brakes, simultaneously causing the trailer air supply valve to pop out, applying the trailer brakes.
Page 156 Brakes Automatic Application If both knobs are pushed in and the brake system air pressure is reduced to approximately 35 psi (249 kPa), the trailer air supply (A) knob automatically pops out applying the emergency or parking brakes on the trailer.
Page 157 Brakes PARKING BRAKE Hydraulic Brakes WARNING: Do not use the gearshift selector in place of the parking brake. Always set the parking brake fully AND make sure the gearshift selector is in position R for vehicles equipped with a manual transmission or position P (if equipped) or N for vehicles equipped with an automatic transmission.
Page 158 Brakes Power Park (Hydraulic Brake Vehicles Only) This feature uses a brake chamber mounted on the chassis to power a spring-applied, hydraulically-released driveline parking brake. The Power Park Brake is controlled by the park brake dash-mounted, yellow knob-type switch. The switch has three positions: apply (out), neutral (central), and release (in).
Page 159 Brakes 3. Select the appropriate drive gear. 4. Push and hold the yellow, dash-mounted parking brake knob until the parking brake light turns off, then release. Parking Brake Light Illumination Due to Low Air Pressure If at any time during vehicle operation air pressure becomes too low, the parking brake may apply and the parking brake light turns on.
Page 160 Brakes If hydraulic pressure is released from the spring brake chamber the power spring applies the brake and, unless hydraulic pressure can be re-established, the spring brake must be released as follows in order to move the vehicle. Loosen the jam nut (A) and un-thread the adjustment rod (B) from the chamber to reduce tension on the cable (C).
Page 161 Brakes WARNING: This control is used for parking only. Do not leave the vehicle unattended after setting the parking brake without placing the transmission inposition R for vehicles equipped with manual transmission or position N (except Allison 2200 transmission) or P (Allison 2200 transmission) for vehicles with automatic transmission.
Page 162 Brakes WARNING: Block the wheels to help prevent the vehicle from moving. WARNING: Unexpected and possibly sudden vehicle movement may occur if these precautions are not taken. Impact wrenches should not be used as they may damage the piston and prevent proper caging of the spring.
Page 163: Traction Control
Traction Control PRINCIPLES OF OPERATION The traction control system helps avoid drive wheel spin and loss of traction. If your vehicle begins to slide, the system applies the rear brakes to individual wheels and, when needed, reduces engine power at the same time.
Page 164: Cruise Control
Cruise Control PRINCIPLES OF OPERATION Cruise control lets you maintain a set speed without keeping your foot on the accelerator pedal. USING CRUISE CONTROL WARNING: Do not use cruise control in heavy traffic or on roads that are winding, slippery or unpaved. Note: Vehicle speed may vary momentarily when driving up or down a steep hill.
Page 165 Cruise Control Changing the Set Speed • Press and hold SET ACCEL to increase or COAST to decrease the set speed. Release the button when you reach the desired speed. • Press and release SET ACCEL to increase or COAST to decrease. The set speed will change in approximately 1 mph (2 km/h) increments.
Page 166: Driving Aids
Driving Aids OPERATING YOUR VEHICLE General Information • Start the vehicle in motion by using the highest gear speed in the transmission that lets the engine easily start the load without slipping the clutch. • Accelerate smoothly and evenly. Rapid acceleration increases fuel consumption without increasing engine performance.
Page 167 Driving Aids Parking WARNING: When parking your vehicle, do not leave the transmission in gear; if the key is in the on position and the vehicle rolls, the engine could start. Failure to follow these instructions could result in an unattended vehicle moving, possibly causing personal injury or property damage.
Page 168: Steering
Driving Aids Hot Weather • Use a permanent-type engine coolant to protect the engine against damage from overheating. • Fill the fuel tank at the end of daily operation to prevent condensation in the fuel system. • Keep external surfaces of the engine, radiator, charge air cooler, A/C condenser and accessories clean to avoid dirt build-up.
Page 169: Air Suspension
Driving Aids AIR SUSPENSION (IF EQUIPPED) Note: The vehicle must not be operated without air in the suspension springs. Operating the vehicle without air in the suspension springs damages the suspension, degrades ride performance and may cause property damage. The air suspension system automatically adjusts to different loads to maintain a constant frame height, allows for ease of vehicle loading and provides improved vehicle ride and increased driver comfort.
Page 170: Upfitter Controls
See your authorized dealer for service. Switch access location is in a connector located in the engine compartment. More detailed information can be found at https://www.fleet.ford.com/truck/bbas/. 2013 F-650/750 (f67) Owners Guide gf, 1st Printing, October 2012 USA (fus)
Page 171: Load Carrying
WARNING: Exceeding any vehicle weight rating limitation could result in serious damage to the vehicle and/or personal injury. Every vehicle manufactured by Ford Motor Company is supplied with information on the Safety Compliance Certification Label, located on either the B-pillar or the driver’s door edge, listing the maximum loading for the vehicle (GVWR), and its axle systems (GAWR) at the tire to ground interface.
Page 172: Vehicle Loading
Load Carrying Unloaded or Lightly Loaded Vehicles WARNING: When operating empty or lightly loaded, sudden or hard braking may induce wheel lockup with loss of vehicle control and the possibility of accident and serious injury, especially on wet or slippery road surfaces. The braking system has been designed to safely stop your vehicle when fully loaded to its GVWR.
Page 173: Towing
Towing TOWING A TRAILER WARNING: Do not exceed the GVWR or the GAWR specified on the certification label. WARNING: Towing trailers beyond the maximum recommended gross trailer weight exceeds the limit of the vehicle and could result in engine damage, transmission damage, structural damage, loss of vehicle control, vehicle rollover and personal injury.
Page 174 Towing ESSENTIAL TOWING CHECKS Service your vehicle more frequently if you tow a trailer. See your scheduled maintenance information. For load specification terms found on the Tire Label and Safety Compliance Certification Label and for instructions on calculating your vehicle’s load, see Load limit in the Load Carrying chapter. Hitches Do not use a hitch that either clamps onto the bumper or attaches to the axle.
Page 175 Towing Trailer lamps are required on most towed vehicles. Make sure all running lights, brake lights, turn signals and hazard lights are working. Before Towing a Trailer Practice turning, stopping and backing up to get the feel of your vehicle-trailer combination before starting on a trip. When turning, make wider turns so the trailer wheels clear curbs and other obstacles.
Page 176: Wrecker Towing
Towing Hook-up 1. Back the tractor squarely under the trailer, engaging the fifth-wheel jaws on the kingpin. Always back up slowly, making sure the trailer is neither too high nor too low. Avoid backing under the trailer from an angle. 2.
Page 177 Towing Before moving the disabled vehicle, check for adequate road clearance of vehicle components. It is recommended the disabled vehicle be unloaded prior to being towed to reduce any abnormal load to the vehicle components resulting from the towing procedures. Before towing, make sure the parking brake is fully released.
Page 178 Towing Towing Vehicles Equipped with a Driver-controlled Differential Lock Note: If the vehicle must be towed to a service facility with the drive axle wheels on the ground, it is necessary to remove the axle shafts before the vehicle is towed. A.
Page 179 Towing Note: One of the axle shafts has two sets of splines. One set to engage with the differential side gear and one set to engage with the shift collar for the differential lock. It may be necessary to rotate the shaft slightly to align the gear spline teeth with the shift collar teeth in order to remove the axle shaft.
Page 180: Driving Hints
Driving Hints BREAKING-IN You need to break in new tires for approximately 300 miles (480 kilometers). During this time, your vehicle may exhibit some unique driving characteristics. Avoid driving too fast during the first 1000 miles (1600 kilometers). Vary your speed frequently and change up through the gears early.
Page 181 Driving Hints DRIVING THROUGH WATER If driving through deep or standing water is unavoidable, proceed very slowly especially if the depth is not known. Never drive through water that is higher than the bottom of the hubs. Traction or brake capability may be limited and your vehicle may stall.
Page 182: Roadside Emergencies
ROADSIDE ASSISTANCE Vehicles Sold in the U.S.: Getting Roadside Assistance To fully assist you should you have a vehicle concern, Ford Motor Company offers a complimentary roadside assistance program. This program is separate from the New Vehicle Limited Warranty and is not applicable to vehicles sold in Canada.
Page 183: Hazard Flasher Control
Canadian Roadside coverage and benefits may differ from the U.S. coverage. Please see your warranty information or visit our website at www.ford.ca for information on Canadian services and benefits. Canadian customers who need to obtain roadside information, call 1-800-665-2006 or visit our website at www.ford.ca.
Page 184: Jump-Starting The Vehicle
Roadside Emergencies JUMP-STARTING THE VEHICLE WARNING: The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could result in injury or vehicle damage. WARNING: Batteries contain sulfuric acid which can burn skin, eyes and clothing, if contacted. Do not attempt to push-start your automatic transmission vehicle.
Page 185 Roadside Emergencies Connecting the Jumper Cables WARNING: Do not connect the end of the second cable to the negative (-) terminal of the battery to be jumped. A spark may cause an explosion of the gases that surround the battery. Note: Do not attach the negative (-) cable to fuel lines, engine rocker covers, the intake manifold or electrical components as grounding points.
Page 186 Roadside Emergencies Jump Starting 1. Start the engine of the booster vehicle and run the engine at moderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for an additional three minutes before disconnecting the jumper cables.
Page 187: Customer Assistance
• the name of the authorized dealer and city where located • the vehicle’s current odometer reading. In some states, you must directly notify Ford in writing before pursuing remedies under your state’s warranty laws. Ford is also allowed a final repair attempt in some states.
Page 188 • Maintenance Schedules • Recalls • Ford Extended Service Plans • Ford Genuine Accessories. In Canada: Mailing address Customer Relationship Centre Ford Motor Company of Canada, Limited P.O. Box 2000 Oakville, Ontario L6J 5E4 Telephone 800-565-3673 (FORD) Online www.ford.ca IN CALIFORNIA (U.S. ONLY) California Civil Code Section 1793.2(d) requires that, if a manufacturer...
Page 189: Getting Assistance Outside The U.s And Canada
(CANADA ONLY) For vehicles delivered to authorized Canadian dealers. In those cases where you continue to feel that the efforts by Ford of Canada and the authorized dealer to resolve a factory-related vehicle service concern have been unsatisfactory, Ford of Canada participates in an impartial third party mediation/arbitration program administered by the Canadian Motor Vehicle Arbitration Plan (CAMVAP).
Page 190 In the United States, using leaded fuel may also result in difficulty importing your vehicle back into the U.S. Ford dealerships outside of the U.S. and Canada may be unable to support the F–650/750 due to the specialized training and servicing requirements of these vehicles.
Page 191: Reporting Safety Defects (U.s. Only)
However, NHTSA cannot become involved in individual problems between you, your dealer, or Ford Motor Company. To contact NHTSA, you may call the Vehicle Safety Hotline toll-free at 1–888–327–4236 (TTY: 1–800–424–9153);...
Page 192: Fuses
Fuses CHANGING A FUSE Fuses WARNING: Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating can cause severe wire damage and could start a fire. If electrical components in the vehicle are not working, a fuse may have blown.
Page 193: Fuse Specification Chart
Fuses FUSE SPECIFICATION CHART Power Distribution Box WARNING: Always disconnect the battery before servicing high current fuses. WARNING: To reduce risk of electrical shock, always replace the cover to the power distribution box before reconnecting the battery or refilling fluid reservoirs. The power distribution box has high-current fuses that protect your vehicle’s main electrical systems from overloads.
Page 194 Fuses Fuse/Relay Fuse Amp Protected Circuits Location Rating Brake warning switch (hydraulic brake vehicles only) Upfitter switches (AUX 1 and AUX 3) Brake pressure switches, ABS event relay DEF (Urea) line heaters (diesel engine only) Ignition switch, Starter cutoff Air tank moisture removal valve Electric trailer brake Passenger compartment fuse box 5 and 21 Instrument cluster/Gateway module...
Page 195 Fuses Fuse/Relay Fuse Amp Protected Circuits Location Rating Ignition switch, Passenger compartment fuse box fuses 19, 29 and 30 Power point Power door lock switches Main light switch, Multi-function switch Passenger compartment fuse box fuses 1, 2, 3, 4, 12, 13, 14 and 15 Fuel heater (diesel engine only) Fuel pump module (gasoline engine only) Power window...
Page 196 Fuses Fuse/Relay Fuse Amp Protected Circuits Location Rating — ABS event relay (hydraulic brake vehicles only) — Body builder relay, back up lamps relay — Auxiliary stop lamp relay — Fuel heater/Fuel transfer pump relay (diesel engine only) — Fuel pump module (gasoline engine only) —...
Page 197 Fuses Passenger Compartment Fuse Panel The fuse box is located behind the passenger airbag cover and can be accessed through the glove box. Fuse/Relay Fuse Amp Protected Circuits Location Rating Horn Flasher relay Power point Data Link Connector (DLC), Engine diagnostic connector, Parking brake warning Run relay —...
Page 198 Fuses Fuse/Relay Fuse Amp Protected Circuits Location Rating Interior lamp relay High beams, Indicator — Not used Dimmer switch, Interior lighting Engine control (diesel engine only) Starting system DRL resistor Air horn, Air suspension dump, Two-speed axle, Driver-controlled locking differential Flasher relay Hydraulic brakes relay, Fuel heater relay (diesel engine only), Air dryer...
Page 199 Fuses Relay Center The relay center is located along the passenger side A-pillar on the right side of the footwell. Relay Relay Description Location Spring applied hydraulic release warning chime module or PCM power VPWR 2, 3 and 4 A/C compressor clutch Power windows Flasher (standard/LED) Upfitter relay 1...
Page 200 Fuses Relay Relay Description Location Shift interlock/EPRNDL display Selective Catalyst Reduction (SCR) system (NOx) (diesel engine only) Door unlock ABS warning indicator DRL #2 Park lights Spare Trailer Tow Relays (If Equipped) TRAILER TRAILER MARKER LAMP USED USED TRAILER TRAILER STOP TAIL TURN...
Page 201: Fuses And Relays
Fuses Fuse/Relay Fuse Amp Protected Circuits Location Rating 30A* Trailer tow turn/stop lamps (combined) Trailer tow turn lamps (separate) — Not used — Trailer tow ABS relay (non electric trailer brake vehicles only) — Trailer tow marker lamp relay — Trailer tow stop lamp relay —...
Page 202: Maintenance
Maintenance GENERAL INFORMATION WARNING: Making modifications to various parts, components and systems of the vehicle, such as brake and steering systems, can adversely affect the quality, reliability and operation of your vehicle and could result in property damage, personal injury or death. Such modifications must be avoided.
Page 203 Maintenance Quality service parts are available through your dealer. If dealer parts are not used, make sure the replacement parts are of equivalent quality. WARNING: The use of inferior parts can adversely affect the quality and reliability of your vehicle which, in turn, can result in property damage, personal injury or death.
Page 204 Maintenance Climate Control System Have the air conditioning system checked each spring. The refrigerant charge, cleanliness of the condenser-evaporator cores and belt condition are essential to system performance. When the air conditioning system is being used daily, remove the fresh air filter (if equipped) once each season and check for dirt, lint, etc.
Page 205 Maintenance Follow the tire manufacturer’s recommended cold inflation pressure for the tire size, load range (ply rating) and steer axle loading typical for their operation (each steer axle tire equals ⁄ steer axle loading). Special applications may warrant a setting based on experience with the type of tire operating loads and conditions.
Page 206 Maintenance Brake System Note: Persons handling brake linings should follow all precautions listed below: WARNING: 1. Always wear a respirator approved by the National Institute of Occupational Studies of Health (NIOSH) or Mine Safety and Appliance (MSA) during all brake service procedures. Wear the respirator from removal of the wheels through assembly.
Page 207 Maintenance Air Brakes WARNING: Do not manually adjust the automatic slack adjusters to correct excessive push rod stroke as it may result in reduced brake effectiveness and a vehicle crash. Excessive push rod stroke indicates that a problem exists with the automatic adjuster, with the installation of the adjuster, or with foundation brake components that manual adjustment does not remedy.
Page 208 Maintenance Some parts such as air brake chamber diaphragm, air compressor and air cleaner should be inspected periodically and replaced if considered unserviceable. Air dryer: Climactic conditions affect performance of desiccant or after-cooler type air dryers. Maintenance schedules must be established for each specific operation.
Page 209 Maintenance Hydraulic Brakes Establish a regular schedule for periodic cleaning, lubrication and adjustment inspection based on vehicle use. Exact maintenance intervals are difficult to predetermine since vehicles are used in a wide variety of applications and conditions. If you are uncertain of the proper schedule for your vehicle, contact your dealer.
Page 210 Maintenance Steering System WARNING: Failure to maintain the steering system in proper condition can cause reduced steering ability resulting in property damage, personal injury or death. Note: Have any steering problems immediately corrected by a qualified service technician. Ask your service technician to examine the steering mechanism. Only minor adjustments may be necessary.
Page 211 Maintenance Catalytic Converter (Diesel Engine) Note: If your vehicle is equipped with a catalytic converter/muffler, do not blend waste oil with diesel fuel. Operate only on ultra low sulfur (less than 15 parts per million sulfur) diesel fuel with a cetane value of 45 or higher.
Page 212 Maintenance Chassis-mounted Charge Air Cooler Visually inspect the core assembly for debris and clogging of external fins with the engine off. Prior to engine operation, remove any debris blocking the core. • Turbocharger-to-charge air cooler • Charge air cooler-to-intake manifold pipe •...
Page 213: Opening And Closing The Hood
Maintenance Supporting Your Vehicle for Service WARNING: Do not use a jack when working under a vehicle. It may give way, causing the vehicle to fall and result in property damage, personal injury or death. Always use floor stands to support the vehicle.
Page 214 Maintenance The hood and fenders are held in position by a latch located on each fender. Before opening the hood, set the parking brake, shift into position N (automatic transmission) or first (manual transmission) and turn the engine off. To open the hood: 1.
Page 215: Engine Oil Dipstick
Maintenance 3. Tilt the hood forward until stopped by the retaining cables. To lower the hood: 1. Push the hood rearward at the top center of the hood above the grille until closed. 2. Engage the latch on each fender. 3.
Page 216: Engine Oil Check
Maintenance ENGINE OIL CHECK Diesel Engine See your engine operator’s manual for information on checking and adding engine oil as well as engine oil specifications, capacities and required maintenance. Gasoline Engine Checking the Engine Oil 1. Make sure the vehicle is on level ground. 2.
Page 217: Engine Coolant Check
Maintenance 2. If the engine oil level is not within the normal range, add engine oil that meets Ford specifications. See Capacities and Specifications for more information. Remove the engine oil filler cap and use a funnel to pour the engine oil into the opening.
Page 218 Note: For best results, coolant concentration should be tested with a refractometer such as Rotunda tool 300-ROB75240E available from your dealer. Ford does not recommend the use of hydrometers or coolant test strips for measuring coolant concentrations. Note: Automotive fluids are not interchangeable; do not use engine coolant, antifreeze or windshield washer fluid outside of its specified function and vehicle location.
Page 219 Severe Climates If you drive in extremely cold climates: • It may be necessary to have a Ford authorized dealer increase the coolant concentration above 50%. • A coolant concentration of 60% provides improved freeze point protection. Engine coolant concentrations above 60% decrease the overheat protection characteristics of the engine coolant and may cause engine damage.
Page 220 Maintenance Vehicles driven year-round in non-extreme climates should use prediluted engine coolant for optimum cooling system and engine protection. What You Should Know About Fail-Safe Cooling (If Equipped) (Gasoline Engine Only) WARNING: If fail-safe cooling activates, pull off the road as soon as safely possible and turn the engine off.
Page 221: Automatic Transmission Fluid Check
Maintenance TRANSMISSION FLUID CHECK Allison Automatic Transmissions See your Allison Automatic Transmission Operator’s Manual for scheduled transmission fluid checks and change intervals. Your transmission does not consume fluid. However, the fluid level should be checked if the transmission is not working properly, i.e., if the transmission slips or shifts slowly or if you notice some sign of fluid leakage.
Page 222 Maintenance TorqShift® Automatic Transmission See the Scheduled Maintenance chapter for scheduled intervals for fluid checks and changes. Your transmission does not consume fluid. However, the fluid level should be checked if the transmission is not working properly, i.e., if the transmission slips or shifts slowly or if you notice some sign of fluid leakage.
Page 223 Maintenance High Fluid Level Fluid levels above the safe range may result in transmission failure. An overfill condition of transmission fluid may cause shift or engagement concerns and possible damage. High fluid levels can be caused by an overheating condition. Adjusting Automatic Transmission Fluid Levels Note: Use of a non-approved automatic transmission fluid may cause internal transmission component damage.
Page 224 Maintenance 3. Clean any dirt from around the filler plug. 4. Remove the filler plug and inspect the fluid level. The fluid level should be at the bottom of the filler plug opening. 5. Add fluid, if necessary, through the filler plug opening. 6.
Page 225 Maintenance Changing the Fluid See the Scheduled Maintenance chapter for rear axle lubricant change intervals. 1. Drain the rear axle while the lubricant is warm. 2. Park the vehicle on level ground. 3. Set the parking brake and shift into position N or P (automatic transmission), or first gear (manual transmission).
Page 226: Brake Fluid Check
Maintenance Air Suspension U-bolt and U-bolt Nut Installation 1. Inspect the threads of the U-bolt and nut for rust and debris. Clean the threads if contaminated. 2. Install the U-bolts and nuts and torque the nuts to seat the cap flat which is about 18 ft-lb (25 N•m) using a diagonal pattern.
Page 227 Clutch Fluid WARNING: Carefully read cautionary information on product label. For MEDICAL EMERGENCY INFORMATION, contact a physician or Poison Control Center immediately; on Ford-Motorcraft® products call: 1-800-959-3673 (FORD). Failure to follow these instructions may result in personal injury. Use only a DOT 3 brake fluid designed to meet manufacturer specifications.
Page 228: Power Steering Fluid Check
Maintenance Clutch Linkage Lubricate the clutch linkage using the following procedure. Use a grease which meets manufacturer specifications. See the Capacities and Specifications chapter. Transmission and clutch removed for clarity. 1. Set the parking brake, shift into first gear and turn the engine off.
Page 229: Fuel Filter
Maintenance 6. Reinstall the dipstick. Remove it again and check the fluid level. Check the MAX. COLD side of the dipstick if the fluid is cool or warm to the touch (approximately 68°F-120°F [20°C-49°C]). The fluid FULL MAX. COLD level should be within the FULL range.
Page 230: Washer Fluid Check
Add fluid to fill the reservoir if the level is low. Only use a washer fluid that meets Ford specifications. See Technical specifications in the Capacities and Specifications chapter. State or local regulations on volatile organic compounds may restrict the use of methanol, a common windshield washer antifreeze additive.
Page 231 Maintenance WARNING: Keep batteries out of reach of children. Batteries contain sulfuric acid. Avoid contact with skin, eyes or clothing. Shield your eyes when working near the battery to protect against possible splashing of acid solution. In case of acid contact with skin or eyes, flush immediately with water for a minimum of 15 minutes and get prompt medical attention.
Page 232 Maintenance If you see any corrosion on the battery or terminals, remove the cables from the terminals and clean with a wire brush. You can neutralize the acid with a solution of baking soda and water. It is recommended that the negative battery cable terminal be disconnected from the battery if you plan to store your vehicle for an extended period of time.
Page 233: Checking The Wiper Blades
Maintenance If the battery has been disconnected or a new battery has been installed, the clock and radio settings must be reset once the battery is reconnected. Always dispose of automotive batteries in a responsible manner. Follow your local authorized standards for disposal.
Page 234: Changing The Wiper Blades
Maintenance CHANGING THE WIPER BLADES 1. To remove the wiper blade, pull the wiper arm away from the vehicle. Pry open the lock cover (A) with your thumb to release the blade. 2. Press the retaining clip to disengage the wiper blade, then pull the wiper blade down (C) toward the windshield to remove it from the arm.
Page 235 Maintenance See the Scheduled Maintenance chapter for the appropriate intervals for changing the air filter element. When changing the air filter element, use only the Motorcraft® air filter element listed. See Motorcraft® part numbers in the Capacities and Spcificationschapter. 1. Locate and disconnect the mass air flow sensor electrical connector on the air outlet tube.
Page 236 Maintenance 5. Release the three clamps that secure the cover to the air filter housing. Push the air filter cover toward the center of the vehicle, and up slightly, to release it. 6. Remove the air filter element from the air filter housing. 7.
Page 237: Adjusting The Headlamps
Maintenance ADJUSTING THE HEADLAMPS The headlamps on your vehicle are properly aimed at the assembly plant. If your vehicle has been in an accident, the alignment of your headlamps should be checked by your authorized dealer. CHANGING A BULB Lamp Assembly Condensation Exterior lamps are vented to accommodate normal changes in pressure.
Page 238 Maintenance 3. Remove the four screws and the retaining bracket from the headlamp bulb. 4. Pull the headlamp bulb out of the housing. Disconnect the electrical connector, then remove the headlamp bulb. 5. Reverse the procedure to install the new bulb. Replacing Front Parking/Turn Signal/Side Marker Lamp Bulbs To remove the parking lamp/turn signal bulbs: 1.
Page 239: Bulb Specification Chart
Maintenance Replacing Brake/Tail/Rear Turn Signal/Reverse/License Plate Lamp Bulbs 1. Remove the four screws and the lamp lens from the lamp assembly. 2. Carefully pull the bulb straight out of the socket. 3. Reverse the procedure to install the new bulb. BULB SPECIFICATION CHART Replacement bulbs are specified in the chart below.
Page 240: Vehicle Care
Vehicle Care GENERAL INFORMATION Your Ford or Lincoln authorized dealer has many quality products available to clean your vehicle and protect its finishes. CLEANING PRODUCTS For best results, use the following products or products of equivalent quality: Motorcraft® Bug and Tar Remover (ZC-42) Motorcraft®...
Page 241 Vehicle Care • Dry the vehicle with a chamois or soft, terry cloth towel in order to eliminate water spotting. • It is especially important to wash the vehicle regularly during the winter months, as dirt and road salt are difficult to remove and cause damage to the vehicle.
Page 242: Waxing
Vehicle Care Cleaning Plastic Exterior Parts Use only approved products to clean plastic parts. • For routine cleaning, use Motorcraft® Detail Wash. • If tar or grease spots are present, use Motorcraft® Bug and Tar Remover. WAXING • Wash the vehicle first. •...
Page 243: Cleaning The Windows And Wiper Blades
Vehicle Care CLEANING THE WINDOWS AND WIPER BLADES The windows and wiper blades should be cleaned regularly. If the wipers do not wipe properly, substances on the vehicle’s glass or the wiper blades may cause squeaking or chatter noise from the blades, and streaking and smearing of the windshield.
Page 244: Cleaning The Instrument Panel And Instrument Cluster Lens
Vehicle Care • If a ring forms on the fabric after spot cleaning, clean the entire area immediately (but do not oversaturate) or the ring will set. • Do not use household cleaning products or glass cleaners, which can stain and discolor the fabric and affect the flame retardant abilities of the seat materials.
Page 245: Cleaning Leather Seats
Vehicle Care CLEANING LEATHER SEATS • Clean spills and stains as quickly as possible. • For routine cleaning, wipe the surface with a soft, damp cloth. For more thorough cleaning, wipe the surface with a mild soap and water solution. In Canada, use Motorcraft® Vinyl Cleaner (CXC-93). Dry the area with a soft cloth.
Page 246: Vehicle Storage
Vehicle Care VEHICLE STORAGE If you plan on storing your vehicle for an extended period of time (30 days or more), read the following maintenance recommendations to make sure your vehicle stays in good operating condition. All motor vehicles and their components were engineered and tested for reliable, regular driving.
Page 247 Vehicle Care Fuel System Note: During extended periods of vehicle storage (30 days or more), fuel may deteriorate due to oxidation. Add a quality gas stabilizer product to the vehicle fuel system whenever actual or expected storage periods exceed 30 days. Follow the instructions on the additive label. The vehicle should then be operated at idle speed to circulate the additive throughout the fuel system.
Page 248 Vehicle Care Removing Your Vehicle from Storage When your vehicle is ready to come out of storage, do the following: • Wash your vehicle to remove any dirt or grease film build-up on window surfaces. • Check windshield wipers for any deterioration. •...
Page 249: Wheels And Tires
Wheels and Tires TIRES Tire Inflation Information WARNING: Always maintain your tires in good condition. Frequently check and maintain correct inflation pressures as specified by tire manufacturers. Inspect periodically for abnormal wear patterns and repair/replace cut or broken tire casings. Always use experienced, trained personnel with proper equipment and correct procedures to mount or remove tires and wheels.
Page 250 Wheels and Tires WARNING: An inflated tire and rim can be very dangerous if improperly used, serviced or maintained. To avoid serious injury, never attempt to re-inflate a tire which has been run flat or seriously under-inflated without first removing the tire from the wheel assembly for inspection.
Page 251 Wheels and Tires Stay out of the trajectory (1) as indicated in the illustration. WARNING: Do not mount tube type tires on tubeless wheels or tubeless tires on tube type wheels. To do so could result in tire or wheel failure and cause property damage, personal injury or death. Preserving proper inflation pressure is a very important maintenance practice to make sure safe vehicle operation and long life for the tires.
Page 252 Wheels and Tires Checking Tire Pressure Always check inflation pressure when tires are cold. Never bleed air from hot tires to relieve normal pressure build-up. Normal increase in pressure due to service conditions is 10–15 psi (69–103 kPa), which is allowable in truck tires.
Page 253 Wheels and Tires Proper tire inflation, toe-in adjustment, loads, and road speeds are important factors governing tire mileage, steering ease and maneuverability. Tire Loading WARNING: Loading tires beyond their rated capacity decreases tire life requiring more frequent replacement of tires. Overloading creates an unsafe condition that may result in sudden air loss from a tire failure resulting in an accident that could cause property damage, personal injury or death.
Page 254 Wheels and Tires If rib tire is used on front axle and lug or off-road type on rear axle positions: • Front (Steering) Axle: Replace tires at front wheels when tread is worn to 4/32 inch (3 millimeters) or less. •...
Page 255 Wheels and Tires Rotating tires from one wheel position to another is a way often used to even out many types of irregular wear or to avoid it altogether. Some of the more effective tire rotation programs are: • Steer tires that have developed some type of irregular wear pattern can be rotated to drive axles if rib tires are being used on all wheel positions.
Page 256 Wheels and Tires Oil-lubricated Front Wheel Bearings During normal vehicle duty cycle, the lubricant and air inside the hub/wheel cavity expands and, if not vented, causes pressure build-up that could cause accelerated seal wear. There are two venting methods that can be used to prevent pressure build-up: •...
Page 257 Wheels and Tires Disc Wheel with Flange Nuts (Hub-piloted). Front wheel mounting of flange nut system. A. Flange nut B. Wheel(s) C. Brake drum D. Wheel stud (22 millimeter) E. Wheel hub 2. Position the outer rear tire and wheel in place over the studs and push it back as far as possible.
Page 258 Wheels and Tires 3. Run the nuts on the studs until they contact the wheel(s). Rotate the wheel assembly a half-turn to permit the parts to seat. 4. Draw-up the nuts alternately following the crisscross sequence illustrated under the following wheel tightening sequence illustrations. Do not fully tighten the nuts.
Page 259: Wheel Lug Nut Torque
Wheels and Tires Proper Torque It is important to tighten and maintain wheel and rim mounting nuts to the proper torque. Loose nuts or over-tightened nuts can lead to premature wear and possible failure of the wheel or mounting hardware. Changing Wheel Types WARNING: Use only the same type and style wheels and mounting hardware to replace original parts.
Page 260: Capacities And Specifications
Capacities and Specifications ENGINE SPECIFICATIONS (GASOLINE ENGINE ONLY) Engine 6.8L V10 engine Cubic inches Required fuel Minimum 87 octane Firing order 1-6-5-10-2-7-3-8-4-9 Spark plug gap 0.039–0.043 inch (1.0–1.1 mm) Ignition system Coil on plug Compression ratio 9.2:1 Engine Drivebelt Routing 6.8L V10 engine with A/C 6.8L V10 engine - without A/C 2013 F-650/750 (f67)
Page 261: Lubricant Specifications
Capacities and Specifications 2013 F-650/750 (f67) Owners Guide gf, 1st Printing, October 2012 USA (fus)
Page 262 Capacities and Specifications 2013 F-650/750 (f67) Owners Guide gf, 1st Printing, October 2012 USA (fus)
Page 263 Capacities and Specifications 2013 F-650/750 (f67) Owners Guide gf, 1st Printing, October 2012 USA (fus)
Page 264 Capacities and Specifications 2013 F-650/750 (f67) Owners Guide gf, 1st Printing, October 2012 USA (fus)
Page 265 Capacities and Specifications 2013 F-650/750 (f67) Owners Guide gf, 1st Printing, October 2012 USA (fus)
Page 266 Capacities and Specifications 2013 F-650/750 (f67) Owners Guide gf, 1st Printing, October 2012 USA (fus)
Page 267 Capacities and Specifications 2013 F-650/750 (f67) Owners Guide gf, 1st Printing, October 2012 USA (fus)
Page 268 Capacities and Specifications 2013 F-650/750 (f67) Owners Guide gf, 1st Printing, October 2012 USA (fus)
Page 269 Capacities and Specifications 2013 F-650/750 (f67) Owners Guide gf, 1st Printing, October 2012 USA (fus)
Page 270 Capacities and Specifications 2013 F-650/750 (f67) Owners Guide gf, 1st Printing, October 2012 USA (fus)
Page 271 Capacities and Specifications 2013 F-650/750 (f67) Owners Guide gf, 1st Printing, October 2012 USA (fus)
Page 272 Capacities and Specifications 2013 F-650/750 (f67) Owners Guide gf, 1st Printing, October 2012 USA (fus)
Page 273 Capacities and Specifications 2013 F-650/750 (f67) Owners Guide gf, 1st Printing, October 2012 USA (fus)
Page 274: Refill Capacities
Capacities and Specifications REFILL CAPACITIES Engine Coolant and Engine Oil Engine Engine Coolant Engine Oil 26.0 quarts Refer to engine operator’s manual. Diesel (24.6L) 26.3 quarts 7.0 quarts (6.6L) Gasoline (24.9L) (includes filter change) Quantities listed are approximate. Add the coolant type originally equipped in your vehicle. Transmission Note: Capacities may be increased if the vehicle is equipped with a cooler.
Page 275 Capacities and Specifications Eaton-Spicer Capacity - Weight Capacity - lb Axle Code Description Pints (kg) (Liters) M190T 19000 (8618) Two-speed 35.0 (17.0) 21060S 21000 (9525) Single reduction 28.0 (13.2) 21060D 21000 (9525) Single reduction, 28.0 (13.2) driver-controlled locking differential M210T 21000 (9525) Two-speed 16.0 (33.0)
Page 276 Capacities and Specifications Meritor Axle Model Capacity - Pints (Liters) RS-23–161 37.2 (17.6) RS-23–180/186 47.3 (22.4) RS-23–240 37.4 (17.7) RS-23–380 63.6 (30.1) Oil capacities are for standard track axles that have been measured at various common drive pinion angles. The quantities listed include enough oil for both wheel ends.
Page 277: Part Numbers
Scheduled Maintenance chapter for the appropriate intervals for changing the spark plugs. Note: Replace the spark plugs with ones that meet Ford material and design specifications for your vehicle, such as Motorcraft® or equivalent replacement parts. The customer warranty may be void for any damage to the engine if such spark plugs are not used.
Page 278: Vehicle Identification Number
The VIN is printed on the Vehicle Rating Decal attached to the vehicle on the edge of the driver’s door or B-Pillar. The VIN also serves as the warranty number. If you ever find it necessary to communicate with Ford Motor Company about your vehicle, always include the VIN in your communication.
Page 279 Capacities and Specifications TRANSMISSION CODE DESIGNATION You can find a transmission code on the Safety Compliance Certification Label. The following table tells you which transmission each code represents. Description Code Six-speed TorqShift® automatic (6R140) 2013 F-650/750 (f67) Owners Guide gf, 1st Printing, October 2012 USA (fus)
Page 280: Scheduled Maintenance
Ford strongly recommends the use of only genuine Ford, Motorcraft® or Ford-authorized remanufactured replacement parts because they are engineered for your vehicle.
Page 281 It is critical that systems are flushed only with new fluid that is the same as that required to fill and operate the system, or using a Ford-approved flushing chemical. Owner Checks and Services Certain basic maintenance checks and inspections should be performed monthly or at six month intervals.
Page 282 Scheduled Maintenance Every Oil Change Engine Inspect engine cooling system hoses, clamps and protection. Inspect drive belt(s). Inspect entire exhaust system (including the inlet Exhaust System pipe(s), muffler(s), outlet pipe(s), clamps and fasteners) for holes, leakage, breakage, corrosive damage and separation from other components. Adjust, service or replace with the same or the equivalent part.
Page 283 Scheduled Maintenance Every Oil Change Steering System Lubricate the steering shaft(s), U-joints and splines if equipped with grease fittings. Lubricate the front axle spindle pins. Lubricate the steering linkage when equipped with grease fittings. Lubricate the power steering gear output shaft. Coolant protection checks should be made just prior to the onset of freezing weather, where applicable.
Page 284 Scheduled Maintenance Observation Maintenance Operation Excessive noise from under the Inspect the vehicle for missing, cab or engine compartment. damaged or mislocated noise shields. Excessive engine noise. Check the engine performance and the engine governor. Engine overheats; excessive fan Inspect the fan, fan shroud and fan noise;...
Page 285 Scheduled Maintenance Observation Maintenance Operation Noisy or difficult to operate. Lubricate body lock cylinders. Headlamp beams in wrong position Check headlamp alignment. when vehicle operating loaded. Windshield washers do not spray Check windshield washer fluid when operated. level. Add fluid if required. During maintenance and repair, protect the fuel tube and the hose assemblies, power steering lines, and brake lines from external heat, acids and abrasions that could damage them.
Page 286 Scheduled Maintenance Noise Emissions Warranty, Prohibited Tampering Acts and Maintenance On January 1, 1978, Federal regulations became effective governing the noise emissions on trucks over 10000 pounds (4536 kilograms) GVWR. The following statements concerning prohibited tampering acts and maintenance and the noise warranty are found in the warranty information, and are applicable to completed trucks.
Page 287 To further help minimize noise emissions degradation throughout the life of the vehicle, Ford Motor Company recommends that this vehicle should be operated in the manner described within this owner’s manual.
Page 288 Information decal. The following services are to be performed at scheduled intervals because they are considered essential to the life and performance of your vehicle. Ford recommends that you perform maintenance on all designated items to achieve best vehicle operation.
Page 289 Scheduled Maintenance 2013 F-650/750 (f67) Owners Guide gf, 1st Printing, October 2012 USA (fus)
Page 290 Scheduled Maintenance 2013 F-650/750 (f67) Owners Guide gf, 1st Printing, October 2012 USA (fus)
Page 291 Scheduled Maintenance 2013 F-650/750 (f67) Owners Guide gf, 1st Printing, October 2012 USA (fus)
Page 292 Scheduled Maintenance 2013 F-650/750 (f67) Owners Guide gf, 1st Printing, October 2012 USA (fus)
Page 293 Scheduled Maintenance 2013 F-650/750 (f67) Owners Guide gf, 1st Printing, October 2012 USA (fus)
Page 294 Scheduled Maintenance 2013 F-650/750 (f67) Owners Guide gf, 1st Printing, October 2012 USA (fus)
Page 295 Scheduled Maintenance 2013 F-650/750 (f67) Owners Guide gf, 1st Printing, October 2012 USA (fus)
Page 296 Scheduled Maintenance 2013 F-650/750 (f67) Owners Guide gf, 1st Printing, October 2012 USA (fus)
Page 297 Scheduled Maintenance 2013 F-650/750 (f67) Owners Guide gf, 1st Printing, October 2012 USA (fus)
Page 298 Scheduled Maintenance 2013 F-650/750 (f67) Owners Guide gf, 1st Printing, October 2012 USA (fus)
Page 299 Scheduled Maintenance 2013 F-650/750 (f67) Owners Guide gf, 1st Printing, October 2012 USA (fus)
Page 300 Scheduled Maintenance 2013 F-650/750 (f67) Owners Guide gf, 1st Printing, October 2012 USA (fus)
Page 301 Scheduled Maintenance 2013 F-650/750 (f67) Owners Guide gf, 1st Printing, October 2012 USA (fus)
Page 302 Scheduled Maintenance 2013 F-650/750 (f67) Owners Guide gf, 1st Printing, October 2012 USA (fus)
Page 303 Scheduled Maintenance 2013 F-650/750 (f67) Owners Guide gf, 1st Printing, October 2012 USA (fus)
Page 304 Scheduled Maintenance 2013 F-650/750 (f67) Owners Guide gf, 1st Printing, October 2012 USA (fus)
Page 305 Scheduled Maintenance 2013 F-650/750 (f67) Owners Guide gf, 1st Printing, October 2012 USA (fus)
Page 306 Scheduled Maintenance 2013 F-650/750 (f67) Owners Guide gf, 1st Printing, October 2012 USA (fus)
Page 307 Scheduled Maintenance 2013 F-650/750 (f67) Owners Guide gf, 1st Printing, October 2012 USA (fus)
Page 308 Scheduled Maintenance 2013 F-650/750 (f67) Owners Guide gf, 1st Printing, October 2012 USA (fus)
Page 309 Scheduled Maintenance 2013 F-650/750 (f67) Owners Guide gf, 1st Printing, October 2012 USA (fus)
Page 310 Scheduled Maintenance 2013 F-650/750 (f67) Owners Guide gf, 1st Printing, October 2012 USA (fus)
Page 311 Scheduled Maintenance 2013 F-650/750 (f67) Owners Guide gf, 1st Printing, October 2012 USA (fus)
Page 312 Scheduled Maintenance 2013 F-650/750 (f67) Owners Guide gf, 1st Printing, October 2012 USA (fus)
Page 313 Scheduled Maintenance Maintenance Record Retention and Service Log 2013 F-650/750 (f67) Owners Guide gf, 1st Printing, October 2012 USA (fus)
Page 314 Scheduled Maintenance EALER ALIDATION EALER ALIDATION P&A C P&A C RO#: RO#: OURS OURS ILEAGE ILEAGE EALER ALIDATION EALER ALIDATION P&A C P&A C RO#: RO#: OURS OURS ILEAGE ILEAGE EALER ALIDATION EALER ALIDATION P&A C P&A C RO#: RO#: OURS OURS ILEAGE...
Page 315 Scheduled Maintenance EALER ALIDATION EALER ALIDATION P&A C P&A C RO#: RO#: OURS OURS ILEAGE ILEAGE EALER ALIDATION EALER ALIDATION P&A C P&A C RO#: RO#: OURS OURS ILEAGE ILEAGE EALER ALIDATION EALER ALIDATION P&A C P&A C RO#: RO#: OURS OURS ILEAGE...
Page 316 Scheduled Maintenance EALER ALIDATION EALER ALIDATION P&A C P&A C RO#: RO#: OURS OURS ILEAGE ILEAGE EALER ALIDATION EALER ALIDATION P&A C P&A C RO#: RO#: OURS OURS ILEAGE ILEAGE EALER ALIDATION EALER ALIDATION P&A C P&A C RO#: RO#: OURS OURS ILEAGE...
Page 317: Sync
SYNC® SYNC is an in-vehicle communications system that works with your Bluetooth-enabled cellular phone and portable media player. This allows you to: • Make and receive calls. • Access and play music from your portable music player. • Use 911 Assist®, Vehicle Health Report and SYNC Services (Traffic, Directions &...
Page 318 Safety Information WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that drivers use extreme caution when using any device that may take their focus off the road. Your primary responsibility is the safe operation of the vehicle.
Page 319 Master Reset to erase all stored information. System data cannot be accessed without special equipment and access to the vehicle’s SYNC module. Ford Motor Company and Ford of Canada do not access the system data for any purpose other than as described...
Page 320 SYNC® USING VOICE RECOGNITION This system helps you control many features using voice commands. This allows you to keep your hands on the wheel and focus on what is in front of you. Initiating a Voice Session Push the voice icon; a tone sounds and Listening appears in the display.
Page 321 SYNC® Adjusting the Interaction Level Push the voice icon; when prompted, say “Voice settings”, then any of the following: When you say: The system: “Interaction mode standard” Provides more detailed interaction and guidance. “Interaction mode advanced” Provides less audible interaction and more tone prompts.
Page 322 SYNC® • Speak naturally, without long pauses between words. • At any time you can interrupt the system while it is speaking by pressing the voice icon. USING SYNC WITH YOUR PHONE Hands-free calling is one of the main features of SYNC. While the system supports a variety of features, many are dependent on your cellular phone’s functionality.
Page 323 SYNC® 4. When prompted on your phone’s display, enter the six-digit PIN provided by SYNC in the radio display. 5. The display indicates when the pairing is successful. Depending on your phone’s capability and your market, the system may prompt you with questions such as setting the current phone as the primary phone (the phone SYNC automatically tries to connect with first upon vehicle start-up), downloading your phone book, etc.
Page 324 SYNC® “PHONE” “Call history missed” “Menu” “Join” “Call <name> at home” “Call <name> at work” OR “Call <name> in office” “Dial” “Phone book <name>” “Phone book <name> at work” OR “Phone book <name> at office” “Call history incoming” “Connections” “Go to privacy” “Hold”...
Page 325 SYNC® Phone book commands: When you ask SYNC® to access a phone book name, number, etc., the requested information appears in the display to view. Press the phone button and say “Call” to call the contact. “DIAL” “411” (four-one-one), “911” (nine-one-one), etc. “700 (seven hundred)”...
Page 326 SYNC® Phone Options during an Active Call During an active call, you have additional menu features which become available such as putting a call on hold, joining calls, etc. Use the arrow buttons to scroll through the menu options. To access: 1.
Page 327 SYNC® When you select: You can: Access your call history log. Call History 1. Press OK to select, then scroll through your call history options (incoming, outgoing or missed). 2. Press OK when the desired selection appears in the display. 3.
Page 328 SYNC® When you select: You can: Phonebook Allows you to access your downloaded phonebook. 1. Press OK to confirm and enter. If your phonebook has fewer than 255 listings, they appear alphabetically in flat file mode. If there are more, they are organized into alphabetical categories.
Page 329 SYNC® Text Messaging Note: This is a phone-dependent feature. SYNC allows you to receive, send, download and delete text messages. The system can also read incoming text messages to you so that you do not have to take your eyes off the road. Receiving a Text Message Note: This is a phone-dependent feature.
Page 330 6. Press OK when the contact appears and press OK again to confirm when the system asks if you would like to send the message. Each text message is sent with the following signature: “This message was sent from my <Ford or Lincoln>”. Pre-defined text message options Can’t talk right now...
Page 331 SYNC® Pre-defined text message options Too funny Can’t wait to see you I’m stuck in traffic Accessing Your Phone Settings These are phone-dependent features. Your phone settings allow you to access and adjust features such as your ring tone, text message notification, modify your phone book and also set up automatic download.
Page 332 SYNC® When you select: You can: Modify Phonebook Modify the contents of your phone book (i.e., add, delete, download). Press OK to select and scroll between: Add Contacts: Press OK to add more contacts from your phone book. Push the desired contact(s) on your phone.
Page 333 SYNC® System Settings System Settings provide access to your Bluetooth Devices and Advanced menu features. Use the arrow buttons to scroll through the menu options. The Bluetooth Devices menu allows you to add, connect, delete and set a phone as primary as well as turn your Bluetooth feature on and off. The Advanced menu allows you to access and set prompts, languages, defaults, perform a master reset, install an application and view system information.
Page 334 SYNC® If you select: You can: Set Bluetooth On/Off Turn the Bluetooth feature on and off. Press OK and scroll to toggle between On and Off. When the desired selection is chosen, press OK. Note: Turning Bluetooth off disconnects all Bluetooth devices and deactivates all Bluetooth features.
Page 335 SYNC® If you select: You can: Choose between English, Espanol and Languages Francais. Once selected, all of SYNC’s radio displays and prompts are in the selected language. 1. Press OK to select and then scroll through the languages. 2. Press OK when the desired selection appears in the display.
Page 336: Assist
SYNC® SYNC APPLICATIONS AND SERVICES (IF EQUIPPED) Note: In order for the following features to work, your cellular phone must be compatible with SYNC. To check your phone’s compatibility, visit www.SYNCMyRide.com, www.SYNCMyRide.ca or www.syncmaroute.ca. • SYNC Services (if equipped, U.S. only): Provides access to traffic, directions and information such as travel, horoscopes, stock prices and more.
Page 337 SYNC® Note: Every phone operates differently. While SYNC 911 Assist works with most cellular phones, some may have trouble using this feature. If a crash deploys an airbag (excludes knee airbags and rear inflatable safety belts [if equipped]) or activates the fuel pump shut-off, your SYNC equipped vehicle may be able to contact emergency services by dialing 911 through a paired and connected Bluetooth-enabled phone.
Page 338 SYNC® In the Event of a Crash Not all crashes deploy an airbag or activate the fuel pump shut-off (which would activate 911 Assist); however, if 911 Assist is triggered, SYNC tries to contact emergency services. If a connected phone is damaged or loses connection to SYNC, SYNC searches for, and tries to connect to, any available previously paired phone and tries to make the call to 911.
Page 339: Vehicle Health Report
SYNC® Vehicle Health Report WARNING: Always follow scheduled maintenance instructions, regularly inspect your vehicle, and seek repair for any damage or problem you suspect. Vehicle Health Report supplements, but cannot replace normal maintenance and vehicle inspection. Vehicle Health Report only monitors certain systems that are electronically monitored by the vehicle and will not monitor or report the status of any other system, (i.e., brake lining wear).
Page 340 Certain versions or updates to Vehicle Health Report may also collect additional vehicle information. Ford may use the vehicle information it collects for any purpose. If you do not want to disclose your cellular phone number or vehicle information, do not run the feature or set up your Vehicle Health Report profile at www.SYNCMyRide.com.
Page 341 For more information, see SYNC Services Terms and Conditions at www.SYNCMyRide.com. If you do not want Ford or its service providers to collect the vehicle travel information or other information identified in the Terms and Conditions, do not activate or use the service.
Page 342 SYNC® 3. Once you are connected to the service, follow the voice prompts to request the desired service, such as “Traffic” or “Directions”. You can also say “What are my choices?” to receive a complete list of available services from which to choose. 4.
Page 343 SYNC® Disconnecting from SYNC Services 1. Press and hold the phone button on the steering wheel. 2. Say “Good-bye” from the SYNC Services main menu. SYNC Services Quick Tips Personalizing You can personalize your Services feature to provide quicker access to your most used or favorite information.
Page 344 SYNC® SYNC AppLink™ Note: Your smartphone must be paired and connected to SYNC to access AppLink. Note: iPhone® users need to connect the phone to the USB port in order to start the application. It is recommended to lock your iPhone® after starting an application.
Page 345 SYNC® To Access Using Voice Commands 1. Press the voice icon. 2. When prompted, say “Mobile Apps”. 3. Say the name of the application after the tone. 4. The app should start. While an app is running through SYNC, you can press the voice button and speak commands specific to the app, such as “Play Station Quickmix”.
Page 346 SYNC® 6. Press OK and scroll through selections of: • Play All • Artists • Albums • Genres • Playlists • Tracks • Explore USB • Similar Music • Return When the desired selection appears in the display, press OK to build your desired music selection.
Page 347 SYNC® “USB” “Play track <name>” “Refine album <name>” “Refine artist <name>” “Refine song <name>” “Refine track <name>” “Repeat off” “Repeat on” “Search album <name>” “Search artist <name>” “Search genre <name>” “Search song <name>” “Search track <name>” “Shuffle off” “Shuffle on” “Similar music”...
Page 348 SYNC® Voice Command Guide “Search/Play Genre” The system searches all the data from your indexed music and, if available, begins to play the chosen type of music. You can only play genres of music which are present in the GENRE metadata tags that you have on your digital media player.
Page 349 SYNC® Media Menu Features The media menu allows you to select your media source, how to play your music (by artist, genre, shuffle, repeat, etc.), and also to add, connect or delete devices. 1. Press AUX and then MENU to enter the Media Menu. 2.
Page 350 SYNC® When you select: You can: Media Settings Choose to shuffle or repeat your music and select your Autoplay settings. Once these selections are turned on, they remain on until turned off. Press SEEK to play the previous or next track. Note: Some digital media players require both USB and line in ports to stream data and music separately.
Page 351 SYNC® Accessing Your Play Menu This menu allows you to select and play your media by artist, album, genre, playlist, track, similar music or even to explore what is on your USB device. 1. Make sure that your device is plugged into the USB port and is turned on.
Page 352 SYNC® When you select: You can: Genres Sort indexed music by genre (category) type. SYNC lists the genres alphabetically in flat file mode. If there are more than 255, SYNC automatically organizes them into alphabetical categories. Press OK to select and then scroll to select the desired genre and press OK.
Page 353 SYNC® When you select: You can: Similar Music Play music similar to what is currently playing from the USB port. The system uses the metadata information of each song to compile a playlist for you. Press OK to select. The system creates a new list of similar songs and begins playing.
Page 354 SYNC® 4. Press OK and then scroll to select from: When you select: You can: Add Bluetooth Allows you to pair additional devices to the system. Device 1. Press OK to select and press OK again when Find SYNC appears in the display. 2.
Page 355 SYNC® 3. Scroll until Advanced appears. 4. Press OK and then scroll to select from the following: When you select: You can: Have SYNC guide you via questions, helpful Prompts hints or ask you for a specific action. 1. Press OK to select and scroll to select between on or off.
Page 356 SYNC® TROUBLESHOOTING Your SYNC system is easy to use. However, should questions arise, see the tables below. Use the website at any time to check your phone’s compatibility, register your account and set preferences as well as access a customer representative via an online chat (during certain hours).
Page 357 SYNC® Phone Issues Issue Possible Possible Solution(s) Cause(s) • Try pushing your phonebook The system says Limitations on Phonebook your phone’s contacts to SYNC by using the Downloaded but capability. Add Contacts feature. • If the missing contacts are my phonebook in SYNC is empty or stored on your SIM card, try is missing...
Page 358 SYNC® USB/Media Issues Issue Possible Possible Solution(s) Cause(s) • Try turning off the device, I am having Possible device trouble connecting malfunction. resetting the device or removing my device. the device’s battery, then trying again. • Make sure you are using the manufacturer’s cable.
Page 359 SYNC® Vehicle Health Report/Services (Traffic, Directions and Information) Issues Issue Possible Possible Solution(s) Cause(s) • Your account • This is a free feature, but you I received a text that the Vehicle may not be must first register online to use it. •...
Page 360 SYNC® Voice Command Issues Issue Possible Possible Solution(s) Cause(s) • You may be • Review the Phone voice SYNC does not understand what using the wrong commands and the Media voice I am saying. voice commands, commands at the beginning of their respective sections.
Page 361 SYNC® Voice Command Issues Issue Possible Possible Solution(s) Cause(s) • You may be • Review the phone voice SYNC does not understand or is using the wrong commands at the beginning of calling the wrong voice commands, the phone section. •...
Page 362: Appendices
SYNC® End User License Agreement (EULA) • You have acquired a device (“DEVICE”) that includes software licensed by FORD MOTOR COMPANY from an affiliate of Microsoft Corporation (“MS”). Those installed software products of MS origin, as well as associated media, printed materials, and “online” or electronic documentation (“MS SOFTWARE”) are protected by international...
Page 363 Neither FORD MOTOR COMPANY nor its suppliers shall be liable for any damages arising out of errors in the speech recognition process.
Page 364 • Consent to Use of Data: You agree that MS, Microsoft Corporation, FORD MOTOR COMPANY, third party software and systems suppliers, their affiliates and/or their designated agent may collect and use technical information gathered in any manner as part of product support services related to the SOFTWARE or related services.
Page 365 DEVICE. UPGRADES AND RECOVERY MEDIA: If the SOFTWARE is provided by FORD MOTOR COMPANY separate from the DEVICE on media such as a ROM chip, CD ROM disk(s) or via web download or other means, and is labeled “For Upgrade Purposes Only” or For Recovery Purposes...
Page 366 For additional information, see http://www.microsoft.com/exporting/. TRADEMARKS: This EULA does not grant you any rights in connection with any trademarks or service marks of FORD MOTOR COMPANY, MS, Microsoft Corporation, third party software or service providers, their affiliates or suppliers.
Page 367 End user notice Microsoft® Windows® Mobile for Automotive Important Safety Information This system Ford SYNC™ contains software that is licensed to Manufacturer FORD MOTOR COMPANY by an affiliate of Microsoft Corporation pursuant to a license agreement. Any removal, reproduction, reverse engineering or other unauthorized use of the software from this system in violation of the license agreement is strictly prohibited and may subject you to legal action.
Page 368 Appendices WARNING: Operating certain parts of this system while driving can distract your attention away from the road, and possibly cause an accident or other serious consequences. Do not change system settings or enter data non-verbally (using your hands) while driving.
Page 369 Appendices Distraction Hazard Any navigation features may require manual (non-verbal) setup. Attempting to perform such set-up or insert data while driving can seriously distract your attention and could cause an accident or other serious consequences. Stop the vehicle in a safe and legal manner before attempting these operations.
Page 370 Index 911 Assist™ ......335 Auxiliary powerpoint ....99 Axle ......141, 204, 223 lubricant specifications ..260 refill capacities ......273 ABS (see Brakes) .....146 Accessing call history/phone book during active call .....325 Battery ........229 Accessing your media menu acid, treating emergencies ..229 features ........348 jumping a disabled battery ..183 Accessing your phone menu maintenance-free ....229...
Page 371 Index Child safety seats - Defrost .........86 booster seats .......31 Diesel exhaust fluid (DEF) ..117 Cleaning your vehicle ....239 Diesel Particulate Filter engine compartment ....241 (DPF) ........104 exterior ........239 instrument panel ....243 Dipstick interior ........242 automatic transmission plastic parts ......241 fluid ..........220 washing ........239 engine oil .........214...
Page 372 Index specifications ......260 Head restraints ......90 Exhaust fumes ......102 Heating ........86 Hood ..........212 Fail safe cooling ......219 Ignition .......101, 259 Fan, Engine Cooling ....216 Information displays ....73 Filter fuel ...........228 Instrument panel cleaning ........243 Flexible Fuel Vehicle (FFV) ..110 cluster ........67 Fuel lighting up panel and cap ...........115...
Page 373: Pairing Your Phone For The First Time
Index Load limits .........171 Playing music (by artist, album, genre, playlist, Locks tracks, similar) ......350 childproof ........40 Power distribution box doors ..........52 (see Fuses) .......192 Lubricant specifications ...260 Power door locks ......52 Lumbar support, seats ....93 Power mirrors ......61 Powerpoint ........99 Power steering ....167, 209 fluid, checking and adding ..227 Manual transmission ....130...
Page 374 Index Safety information ....317 Safety restraints ..42–44, 46–47 Tail lamps Belt-Minder® ......47 bulb replacement ....236 extension assembly ....46 for adults .......42–44, 46 Temperature control for children ......28, 33 (see Climate control) ....86 safety belt maintenance ...50 seat belt maintenance ....50 Text messaging ......328 warning light and chime ..47 Text messaging...
Page 375 Index Washer fluid ......229 Water, Driving through .....180 Vehicle health report ....338 Wheels ........254 Vehicle Identification Number Windows (VIN) ........277–278 power .........58 Vehicle loading ......171 Windshield washer fluid and Ventilating your vehicle ...102 wipers ..........54 Voice commands in media checking and adding fluid ..229 mode ..........345 replacing wiper blades ...233 Voice commands in phone...

This manual is also suitable for:

F-750 2013

Ford f-650 2013 Owner's Manual

Table of Contents

Table of Contents

Table of Contents

Introduction

Vehicle Inspection Guide

Child Safety

Safety Belts

Keys and Remote Control

Locks

Steering Wheel Controls

Wipers and Washers

Lighting

Windows and Mirrors

Instrument Cluster

Information Displays

Audio System AM/FM Stereo

Climate Control

Seats

Auxiliary Power Points

Starting and Stopping the Engine

Fuel and Refueling

Transmission

Brakes

Traction Control

Cruise Control

Driving Aids

Load Carrying

Towing

Driving Hints

Roadside Emergencies

Customer Assistance

Fuses

Maintenance

Vehicle Care

Wheels and Tires

Capacities and Specifications

Scheduled Maintenance

Sync

Appendices

Quick Links

Related Manuals for Ford f-650 2013

Summary of Contents for Ford f-650 2013