M-Link Control; Rs-232C Connection; Hdmi Device; Dvi Device - Mitsubishi WD-52525 Owner's Manual

Connecting M-Link Control RS-232C Connection, or a HDMI
or DVI Device
M-Link Control RS-232C Connection
Figure 14
A 9 pin RS-232C cable is required. This is not included with
the TV. It may be available at your local electronics retailer
As M-Link Control, connect to a Mitsubishi HD
Receiver/Controller, like the HD-5000 or HD-6000. As
RS-232C, connect to other external controllers. See
mitsubish-tv.com for RS-232C command protocol.
Connect a 9 pin RS-232C cable from the TV back
panel to the M-Link or RS-232C on the external control
device.
TV back panel (section detail)
IEEE1394
INPUT/OUTPUT
PC
IR EMITTER
VGA/SVGA/XGA/
NetCommand R
720p
60 Hz
L
DVI
L
Analog Audio
R
R
ANT-2
AUX PC-
AUDIO
DTV/
CABLE/
VHF/
UHF
HDMI ANT-1
PC-
M-LINK MAIN INPUT
M-LINK
CONTROL/
RS-232C
DIGITAL
AUDIO
CARD
TOP
Computer with Monitor Output
Figure 14. Connecting M-Link Control

HDMI Device

Figure 15
An HDMI to HDMI cable is required. This is not included with
the TV. It may be available at your local electronics retailer
Connect an HDMI cable from the TV back panel to the
HDMI device output. HDMI devices provide video and
audio through this cable, so no other connection is
required.
TV back panel (section detail)
HD-6000 Receiver
Figure 15. Connecting HDMI Device
26
IEEE1394
INPUT/OUTPUT
IR EMITTER PC
NetCommand VGA/SVGA/XGA/
R
720p
60 Hz
L
DVI
L
Analog Audio
R R
ANT-2
AUX PC-
AUDIO
DTV/
CABLE/
VHF/
UHF
HDMI ANT-1 PC-
M-LINK MAIN INPUT
M-LINK
CONTROL/
RS-232C
DIGITAL
AUDIO
CARD
TOP

DVI Device

Figure 16
A DVI-to-HDMI cable or DVI/HDMI adaptor and HDMI cable
and audio cables are required. These are not included with the
TV. They may be available at your local electronics retailer.
1. Connect the DVI-to-HDMI cable (recommended)
(or DVI/HDMI adaptor with an HDMI cable) from the
DVI device's back panel to the TV back panel.
NOTE: If you are using a DVI/HDMI adaptor, it is
important to connect the adaptor to the DVI side for
best performance.
2. Connect a set of audio cables from AUDIO OUT on
the the DVI device back panel to the DVI Analog
Audio input on the TV back panel. The red cable
connects to the R (right) channel, and the white
cable connects to the L (left) channel.
NOTE: The HDMI connection supports copy
protection (HDCP). Some devices require
connecting to an analog input first, in order to view
on-screen menus and select DVI as the ouput.
Please review your equipment instructions for DVI
connectivity and compatibility.
IEEE1394
INPUT/OUTPUT
IR EMITTER
NetCommand R
2.
DVI DVI DVI
L L
Analog Audio Analog Audio Analog Audio
R R
ANT-2
AUX
DTV/
CABLE/
VHF/
UHF
1.
HDMI HDMI ANT-1
M-LINK M-LINK MAIN
M-LINK
CONTROL/
RS-232C DIGITAL
AUDIO
CARD
TOP
DVI-TO-HDMI CABLE
1.

DVI DEVICE

��� ���������
��� ���
��� ���
�����
Figure 16. Connecting a DVI Device
CAUTION: To ensure continued FCC
compliance, the user must use a shielded
video interface cable with bonded ferrite
cores at both ends when using the PC
input.
PC
VGA/SVGA/XGA/
720p
AUDIO
MONITOR
60 Hz
VIDEO S-VIDEO
R L(MONO) OUTPUT
L
AUDIO 2
R
AUDIO/VIDEO 1
PC-
AUDIO
INPUT-1
INPUT-2
PC-
INPUT
COMPONENT-1
YPbPr (480i/480p/720p/1080i)
COMPONENT-2
YPbPr (480i/480p/720p/1080i)
INPUT-DTV
YPbPr / RGB HV
(480i/480p/720p/1080i)
Pr/R Pb/B Y/G
V H
2.
�
�����
�
�� ���